Apc Smart-UPS Battery Systems SRT48BP Käyttöohje
Lue alta 📖 käyttöohje suomeksi merkille Apc Smart-UPS Battery Systems SRT48BP (16 sivua) kategoriassa UPS. Tämä opas oli hyödyllinen 6 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/16
Installation Guide Smart-UPS™ On-Line
External Battery Pack SRT48BP/48RMBP
Important Safety Messages
Read the instructions carefully to become familiar with the equipment before trying to install, operate, service or
maintain it. The following special messages may appear throughout this manual or on the equipment to warn of
potential hazards or to call attention to information that clarifies or simplifies a procedure.
The addition of this symbol to a Danger or Warning safety label indicates that an electrical hazard exists
which will result in personal injury if the instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible injury or death.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious
injury.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious
injury.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate
injury.
NOTICE
NOTICE is used to address practices not related to physical injury.
Smart-UPS On-Line External Battery Pack SRT48BP/48RMBP2
Safety and General Information
• Adhere to all national and local electrical codes.
• Changes and modifications to this unit not expressly approved by APC by Schneider Electric could void the
warranty.
• This unit is intended only for indoor use in a controlled environment.
• Do not operate this unit in direct sunlight, in contact with fluids, or where there is excessive dust or humidity.
• Be sure the air vents on the unit are not blocked. Allow adequate space for proper ventilation.
• The equipment is heavy. Always practice safe lifting techniques adequate for the weight of the equipment.
• The batteries are heavy. Remove the batteries before installing the UPS and external battery packs (XLBPs) in a
rack.
• Always install XLBPs at the bottom in rack-mount configurations. The UPS must be installed above the XLBPs.
• The UPS will recognize as many as 10 XLBPs connected to the UPS.
Note: For each XLBP added, increased recharge time will be required.
• Do not dispose of batteries by burning them. The batteries may explode.
• Do not open or mutilate batteries. Released electrolyte is harmful to the skin and eyes, and may be toxic.
• Always recycle used batteries.
• Recycle the package materials or save them for reuse.
• Additional safety information can be found in the Safety Guide supplied with this unit.
Battery safety
• When replacing batteries, replace with the same number and type of batteries as originally installed in
the equipment.
• Batteries typically last for two to five years. Environmental factors impact battery life. Elevated
ambient temperatures, poor quality utility power, and frequent short duration discharges will shorten
battery life. Batteries should be replaced before end of life.
• Replace batteries immediately when the unit indicates battery replacement is necessary.
• Schneider Electric uses Maintenance-Free sealed Lead Acid batteries. Under normal use and handling,
there is no contact with the internal components of the battery. Over charging, over heating or other
misuse of batteries can result in a discharge of battery electrolyte. Released electrolyte is toxic and
may be harmful to the skin and eyes.
• CAUTION: Before installing or replacing the batteries, remove jewelry such as wristwatches and
rings.
High short circuit current through conductive materials could cause severe burns.
• CAUTION: Do not dispose of batteries in a fire. The batteries may explode.
• CAUTION: Do not open or mutilate batteries. Released material is harmful to the skin and eyes and
may be toxic.
Smart-UPS On-Line External Battery Pack SRT48BP/48RMBP 3
Overview
• To verify that installation of an external battery pack (XLBP) has been successful, go to the UPS display
interface.
Perform a Visible Alarm Test to determine if the XLBP is recognized by the UPS.
The LED on the XLBP will flash if successful communication has been established.
• When viewing the status of an XLBP on the UPS display interface screen, the LED on the corresponding XLBP
will flash.
• When an RBC needs to be replaced, perform a Runtime Calibration Test to verify that battery replacement is
required.
Package Contents
Inspect the contents upon receipt. Notify the carrier and dealer if there is damage.
Included with all models
Front bezel Ground cable
2 pan head screws to secure the
ground cable
2 tie brackets
4 flat head screws to secure tie
brackets
User Documentation CD
1 pan head screw to secure the
XLBP battery cable connector to
an XLBP or to the UPS.
Included with Tower models only
Stabilizer brackets are supplied with the UPS models
The XLBP includes 1 pair of stabilizer bracket connectors
4 flat head screws to secure tower stabilizer
brackets to the UPS
Included with Rack-Mount models only
Rail Kit with instructions and hardware for
installing rails in a rack
• 1 pair rack-mount brackets
• 6 flat head screws to secure rack-mount brackets to the UPS
• 4 ornamental screws to secure rack-mount brackets to the rails
su04
34a
x6
x4
Tuotetiedot
| Merkki: | Apc |
| Kategoria: | UPS |
| Malli: | Smart-UPS Battery Systems SRT48BP |
Tarvitsetko apua?
Jos tarvitset apua merkille Apc Smart-UPS Battery Systems SRT48BP esitä kysymys alla ja muut käyttäjät vastaavat sinulle
UPS Apc Käyttöohjeet
4 Joulukuuta 2024
4 Joulukuuta 2024
4 Joulukuuta 2024
4 Joulukuuta 2024
UPS Käyttöohjeet
Viimeisimmät UPS Käyttöohjeet
25 Joulukuuta 2024
10 Joulukuuta 2024
10 Joulukuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
22 Lokakuuta 2024
22 Lokakuuta 2024
22 Lokakuuta 2024