Arecont Vision AV2256PM Käyttöohje

Lue alta 📖 käyttöohje suomeksi merkille Arecont Vision AV2256PM (20 sivua) kategoriassa Turvakamera. Tämä opas oli hyödyllinen 4 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/20
Arecont Vision MegaDome® 2 Installation Manual
0 | P a g e
Arecont Vision MegaDome® 2 Installation Manual
1 | P a g e
MegaDome® 2 Installation Manual
Inside the box:
A. Arecont Vision MegaDome® 2 camera
B. Mounting template
C. Rubber gasket (preinstall on bottom of
camera)
D. AC & DC p ower cable
E. I/O cable
F. m Installation anual
G. CD with AV100 oftware and s user
manuals (License Key Required for
Recording)
H. Pack of four (4) wood screws and four (4)
dry wall anchors
I. -K Security L ey
J. -One double sided hex key
K. -One single sided hex key
Not included but needed:
#1 Phillips head screwdriver
#2 Phillips head screwdriver
Image 1
Mounting the Camera:
1. Remove the camera and hardware from the
box.
2. Using the mounting template, prepare the
mounting surface for camera installation.
NOTE: the 19.5mm diameter hole on the
Mounting template is where the Ethernet
cable will be exiting the MegaDome®, align
accordingly. If using the side conduit hole,
please see step 4 . following
3. Using Security L key, loosen the four (4) -
screws securing the dome cover (Image 2).
Remove the vandal resistant dome cover.
NOTE: Do not remove the screws from the
dome cover.
2 Image
G
F
E
C
A
D
B
H
I
J
K
Arecont Vision MegaDome® 2 Installation Manual
2 | P a g e
4. If you are using the side conduit opening,
remove the conduit plug by first removing the
socket set screw using the provided double-
sided hex . key (Image 3)
Image 3
Note: Make sure that you install the rubber
gasket on the bottom of the camera to form a
weather tight seal with the mount surface.
5. Run the Ethernet cable through the gasket
and hole the on the bottom of the camera
( 4)Image or run cable through the side the
conduit and plug it into the RJ45 port. NOTE:
If the camera will be powered via PoE, please
skip to step 6.
6. If the camera will be powered by an AC or DC
power supply, run the supplied power cable
through the gasket and on the bottom the hole
of the camera or run the cable through the
side conduit and connect it to its respective
connector inside the camera (Image 3).
NOTE: Make sure that your installation of
wires complies with Electrical Code of the
local government where the camera is
installed and no bare wirethat s are exposed.
Image 4
7. Align the holes in the camera with the
prepared holes on the mounting surface.
Attach the camera to the mounting surface
with the wood screws or any optional
hardware suitable for the mounting surface.
8 . Apply silicon on the bottom of the camera to
form a weather tight seal with the mount
surface (if necessary).
HOLE
POWER
RJ- 45

Tuotetiedot

Merkki: Arecont Vision
Kategoria: Turvakamera
Malli: AV2256PM

Tarvitsetko apua?

Jos tarvitset apua merkille Arecont Vision AV2256PM esitä kysymys alla ja muut käyttäjät vastaavat sinulle




Turvakamera Arecont Vision Käyttöohjeet

Turvakamera Käyttöohjeet

Viimeisimmät Turvakamera Käyttöohjeet

Lorex

Lorex E893AB-E Käyttöohje

2 Huhtikuuta 2025
Yale

Yale YRD430 Käyttöohje

30 Maaliskuuta 2025
BirdDog

BirdDog X1 Käyttöohje

30 Maaliskuuta 2025
BirdDog

BirdDog X1 Ultra Käyttöohje

30 Maaliskuuta 2025
Hanwha

Hanwha QNE-C9013RL Käyttöohje

30 Maaliskuuta 2025
HiLook

HiLook THC-T150-M Käyttöohje

27 Maaliskuuta 2025
Reolink

Reolink W320 Käyttöohje

27 Maaliskuuta 2025