Boss Chorus CE-2W Käyttöohje
Boss
Kitaran vahvistin
Chorus CE-2W
Lue alta 📖 käyttöohje suomeksi merkille Boss Chorus CE-2W (1 sivua) kategoriassa Kitaran vahvistin. Tämä opas oli hyödyllinen 2 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/1
Owner’s Manual
Standard/CE-1 mode switch
Switches the mode.
Standard
The sound of the CE-2.
This is a chorus sound notable for its clarity; it will not
impair the crispness of your guitar sound.
CE-1 Chorus
The chorus sound of the CE-1.
While providing an easily recognizable chorus eect
with deeper modulation, this chorus is distinctively
mild.
CE-1 Vibrato
The vibrato sound of the CE-1.
This is a unique chorus with strongly varying
modulation.
DEPTH knob
Adjusts the depth of the chorus.
RATE knob
Adjusts the rate of the chorus.
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).
After reading, keep the document(s) where it will be available for immediate reference.
Precautions When Connecting
5 To prevent malfunction and equipment failure, always turn
down the volume, and turn o all the units before making any
connections.
5 Once everything is properly connected, be sure to follow the
procedure below to turn on their power. If you turn on equipment
in the wrong order, you risk causing malfunction or equipment
failure.
When powering up: Turn on the power to your guitar amp last.
When powering down: Turn o the power to your guitar amp rst.
Use of Battery
5 A battery was installed in the unit before it left the factory. The life
of this battery may be limited, however, since its primary purpose
was to enable testing.
5 If you handle batteries improperly, you risk explosion and uid
leakage. Make sure that you carefully observe all of the items
related to batteries that are listed in “USING THE UNIT SAFELY” and
“IMPORTANT NOTES” (supplied on a separate sheet).
5 When operating on battery power only, the unit’s indicator will
become dim when battery power gets too low. Replace the
battery as soon as possible.
5 Batteries should always be installed or replaced before connecting
any other devices. This way, you can prevent malfunction and
damage.
Specications
Nominal Input Level -20 dBu
Input Impedance 1 MΩ
Nominal Output
Level -20 dBu
Output Impedance 1 kΩ
Recommended Load
Impedance 10 kΩ or greater
Power Supply Alkaline battery (9 V, 6LR61) or
Carbon-zinc battery (9 V, 6F22)
AC adaptor (PSA series: sold separately)
Current Draw 25 mA
* Expected battery life under continuous use:
Alkaline: 32 hours
Carbon: 18 hours
These gures will vary depending on the
actual conditions of use.
Dimensions 73 (W) x 129 (D) x 59 (H) mm
2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches
Weight 450 g / 1lb (including battery)
Accessories Leaet (“USING THE UNIT SAFELY,” “IMPORTANT
NOTES,” and “Information”)
Alkaline battery (9 V, 6LR61)
Options
(sold separately) AC adaptor (PSA-series)
* 0 dBu = 0.775 Vrms
* This document explains the specications of the product at the
time that the document was issued. For the latest information,
refer to the Roland website.
Thumbscrew
When this screw is loosened, the
pedal will open, allowing you to
change the battery.
* For instructions on changing
the battery, refer to “Changing
the Battery.”
AC Adaptor
(PSA series; sold separately)
Electric Guitar
English
7This is a “WAZA CRAFT series” eect unit featuring analog circuitry designed with attention to every detail in pursuit of the nest sound.
7Standard mode completely replicates the sound of the CE-2 chorus, known for its mild modulation.
7In addition, this unit provides a CE-1 mode (chorus, vibrato) which reproduces the sound of the world’s rst chorus unit, the CE-1.
Main Features
INPUT jack
This jack accepts signals coming from
a guitar or other musical instrument, or
another eects unit.
* The INPUT jack doubles as the power switch. Power
to the unit is turned on when you plug into the
INPUT jack; the power is turned o when the cable
is unplugged. To prevent unnecessary battery
consumption, be sure to disconnect the plug from the
INPUT jack when not using the eects unit.
Panel Descriptions
DC IN jack
Accepts connection of an AC Adaptor (PSA series; sold separately). By using an AC Adaptor, you can play
without being concerned about how much battery power you have left.
* Use only the specied AC adaptor (PSA series; sold separately), and connect it to an AC outlet of the
correct voltage. Do not use any other AC adaptor, since this may cause malfunction.
* If the AC adaptor is connected while a battery is installed, the power
supply is drawn from the AC adaptor.
* We recommend that you keep batteries installed in the unit even
though you’ll be powering it with the AC adaptor. That way, you’ll be
able to continue a performance even if the cord of the AC adaptor gets
accidentally disconnected from the unit.
CHECK indicator
This indicator shows whether the eect is on or o, and also doubles as the battery check
indicator. The indicator lights when the eect is on.
* If you’re powering the unit with a battery and the CHECK indicator goes dim— or doesn’t
light at all—when you try to turn the eect on, the battery is near depletion and should be
replaced. For instructions on changing the battery, refer to “Changing the Battery.”
Pedal switch
This switch turns the eect on/o.
OUTPUT B jack
Use this jack for stereo output.
The stereo output produced by this output in
conjunction with the chorus sound from the
OUTPUT A (MONO) jack provides a spacious
chorus eect.
Only the direct sound is output from the
OUTPUT B jack.
OUTPUT A (MONO) jack
The direct sound and chorus sound are
mixed and output from this jack.
If you use the OUTPUT B jack for stereo
output, this jack outputs only the chorus
sound.
© 2016 Roland Corporation 02
Guitar Amplier
Guitar Amplier
OUTPUT jacks
Mono output
Chorus sound + Direct sound
Stereo output
Direct soundChorus sound
Changing the Battery
1. Hold down the pedal and loosen the thumbscrew, then
open the pedal upward.
* The pedal can be opened without detaching the thumbscrew
completely.
Thumbscrew
Battery Housing
Pedal
Spring Base
Coil Spring
Guide Bush
Hole
Battery Snap
Cord
Battery
Snap
9 V Battery
2. Remove the old battery from the battery housing, and
remove the snap cord connected to it.
3. Connect the snap cord to the new battery, and place
the battery inside the battery housing.
* Be sure to carefully observe the battery’s polarity (+ versus -).
4. Slip the coil spring onto the spring base on the back of
the pedal, and then close the pedal.
* Carefully avoid getting the snap cord caught in the pedal, coil
spring, and battery housing.
5. Finally, insert the thumbscrew into the guide bush
hole and fasten it securely.
Tuotetiedot
| Merkki: | Boss |
| Kategoria: | Kitaran vahvistin |
| Malli: | Chorus CE-2W |
Tarvitsetko apua?
Jos tarvitset apua merkille Boss Chorus CE-2W esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Kitaran vahvistin Boss Käyttöohjeet
13 Joulukuuta 2024
13 Joulukuuta 2024
13 Joulukuuta 2024
13 Joulukuuta 2024
13 Joulukuuta 2024
13 Joulukuuta 2024
13 Joulukuuta 2024
13 Joulukuuta 2024
13 Joulukuuta 2024
13 Joulukuuta 2024
Kitaran vahvistin Käyttöohjeet
- Kitaran vahvistin Yamaha
- Kitaran vahvistin Vox
- Kitaran vahvistin Roland
- Kitaran vahvistin Blackstar
- Kitaran vahvistin SPL
- Kitaran vahvistin Radial Engineering
- Kitaran vahvistin Peavey
- Kitaran vahvistin Mooer
Viimeisimmät Kitaran vahvistin Käyttöohjeet
12 Joulukuuta 2024
4 Joulukuuta 2024
21 Lokakuuta 2024
21 Lokakuuta 2024
21 Lokakuuta 2024
21 Lokakuuta 2024
21 Lokakuuta 2024
21 Lokakuuta 2024
19 Lokakuuta 2024
19 Lokakuuta 2024