Chief RPMA361 Käyttöohje

Lue alta 📖 käyttöohje suomeksi merkille Chief RPMA361 (1 sivua) kategoriassa Projektorin lisävaruste. Tämä opas oli hyödyllinen 3 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/1
8800-002992 Rev00
©2017 Milestone AV Technologies
www.milestone.com
06/17
Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes
no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief, a products division of Milestone AV Technologies
6436 City West Parkway, Eden Prairie, MN 55344
• P: 800.582.6480 / 952.225.6000 F:877.894.6918 / 952.894.6918
I N S T A L L A T I O N I N S T R U C T I O N S
SLB-361 and SLM-361 Interface Brackets
SLB-361 and SLM-361 Interface Brackets are designed for use with Chie Series Projector Mounts. See the specific installation instructions
provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB interface bracket. If an SLM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place spacers over the threaded inserts in the bottom of the projector.
4. Place the interface bracket onto the bottom of the projector, aligning the mounting holes in the bracket with the spacers and threaded
inserts in the bottom of the projector and ensuring that triangle in bracket points towards front of projector.
5. Position M6 x 25mm mounting screws with M6 flat washers into the spacers, threaded inserts and bracket side tabs. Tighten all fasteners
at this time, securing the bracket to the projector.
NOTE: Security screws can be substituted when mounting Interface bracket to projector by using the parts and installation instructions in the
All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (4) Screw, Phillips Pan Head, Machine, M6 x 25mm
(6) 10-24 Thumb Nuts ** (4) Spacer, Nylon, .500 x .257 x .625"
(1) All-Points Security Kit (4) Washer, M6
(1) 5/32" Security Hex Key
**Only used when installing SLB interface brackets.
SLB-361 SLM-361
Towards front
of projector
Towards front
of projector

Tuotetiedot

Merkki: Chief
Kategoria: Projektorin lisävaruste
Malli: RPMA361

Tarvitsetko apua?

Jos tarvitset apua merkille Chief RPMA361 esitä kysymys alla ja muut käyttäjät vastaavat sinulle