CRUX RVCCH-75WM Käyttöohje

CRUX Ei luokiteltu RVCCH-75WM

Lue alta 📖 käyttöohje suomeksi merkille CRUX RVCCH-75WM (3 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 2 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/3
- Interface includes Audio / Video Input to connect an extra A/V source.
- OEM style Spare Tire mount reverse camera included.
- Camera has moving parking guide lines to show path direcon while backing up.
- Acvates MYGIG Screen for enabling Video features.
- Supports vehicles with manual transmission. See note below.
- Plug and Play connecons for ease of use.
NOTE: Does not supply +12V Reverse Trigger on vehicles with manual transmission.
Camera power must be tapped from the +12V reverse light wire instead.
-75WM MODULE CH
-75WM HARNESS CH
CCH-01M SPARE TIRE MOUNT CAMERA with MOVING LINES
Rev.0926 17
1 / 3
INSTALLING THE CAMERA AND INTERFACE
1. Remove the outside mounted spare re.
2. Mount the metal bracket onto the spare re bolts and secure with the star washers. camera’s
3. Route the cable towards the radio and make the power and video connecons.
4. Remove the factory radio to gain access to the factory connectors.
5. Plug in the T-harness with WHITE and GRAY connectors. (See Wiring Diagram above)
6. Connect the 8-pin Molex connector from the T-harness with GRAY connectors to the CAN Interface.
7. Use the WHITE 12V Reverse Output wire to power the camera (see Wiring Diagram above). DO NOT
connect the red power wire, near the camera, insulate this red wire to avoid to the reverse light and
from shorng. the vehicle has a manual transmission, the camera power must be tapped to the If
+12V reverse light wire instead. In this case the WHITE 12V Reverse Output wire is not used and
should be insulated to avoid from shorng.
8. Plug in the YELLOW MALE RCA from the camera cable to the YELLOW FEMALE RCA of the T-Harness
with WHITE connectors.
9. Connect GREEN wire to +12V for a non permanent Video in Moon feature.
10. Set the proper DIP Switch sengs on the CAN Interface. (See Chart above)
11. Cut the thin white wire on the camera cable to enable the parking guide lines.
12. Test the camera before re-installing the radio.
Rev.0926 17
2 / 3
Please note that the WHITE 12V
Reverse Output wire does not
supply power on vehicles with
manual transmission and should
be insulated to avoid from
shorng. Connect the camera
power to the OE reverse light
+12V wire instead.
DIP SWITCH SETTING
OFF
VIM Disable
ON
Rear-View Camera Enable
OFF
N/A
OFF
Opon for GREEN Wire
OFF
CAN Terminaon Radio Side
ON
CAN Terminaon Car Side
The parking lines are there to assist you while reversing. To acvate the parking lines simply cut/disconnect the
WHITE loop wire located near the 4 pin camera connector.
What the Lines mean:
Green Line: CLEAR
Yellow Line: GETTING CLOSE
Red Line: WARNING - VERY CLOSE
White Line: SHOWS THE PATH DIRECTION
VES will be your source for the AV Input.
To access the VES buon, press the RADIO/MEDIA buon on the le side of the radio. The VES buon is only
acve aer the interface is properly installed.
JEEP
2007 2017 WRANGLER
MyGig Radio
Rev.0926 17
3 / 3

Tuotetiedot

Merkki: CRUX
Kategoria: Ei luokiteltu
Malli: RVCCH-75WM

Tarvitsetko apua?

Jos tarvitset apua merkille CRUX RVCCH-75WM esitä kysymys alla ja muut käyttäjät vastaavat sinulle




Ei luokiteltu CRUX Käyttöohjeet

CRUX

CRUX DKGM-C2S Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX DKVW-21 Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX SOHTL-20 Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX AVIGM-04S Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX SOCVW-21 Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX AUX-MB1 Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX SWR-A Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX AUX-MB2 Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX DKGM-C2D Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX RVCHN-76C Käyttöohje

15 Lokakuuta 2024

Ei luokiteltu Käyttöohjeet

Viimeisimmät Ei luokiteltu Käyttöohjeet