CRUX SOOGM-19L Käyttöohje

CRUX Ei luokiteltu SOOGM-19L

Lue alta 📖 käyttöohje suomeksi merkille CRUX SOOGM-19L (4 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 6 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/4
Crux Interfacing Solutions • Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.071720
1 of 4
RAD IO REP LA CEMENT
SWC RET ENTIO N
+
R
INTERFACING SOLUTIONS
- Retains factory features in select GM LAN V2 (LIN) Bus vehicles while functioning with an aftermarket radio.
- Retains OnStar functionality.
- Retains all chime functions.
- Retains OEM Auxiliary Input.
- Retains Factory Bluetooth in Vehicles 2008-upwards if equipped with the new OnStar device.
- Retains factory Steering Wheel Controls via built-in, preprogrammed interface.
- Retains RAP (Retained Accessory Power).
- Includes factory backup camera connection for the IO3 system. (vehicles with IO4, IO5 & IO6 systems can be hard
wired to retain the OEM camera. See page 3)
PRODUCT FEATURES:
PARTS INCLUDED:
INSTALLATION DIAGRAM:
SOOGM-19L MODULE SOOGM-19L HARNESS SWC CABLE ANTENNA ADAPTER
SOOGM-19L
OnStar Radio Replacement Interface with Steering Wheel
Control Retention for GM LAN v2 (LIN) Bus Vehicles 2014 - 2018
AFTERMARKET
RADIO
Reverse Red/White















TO FACTORY
HARNESS
16-Pin Green
Connector
20-Pin Gray
Connector
4-Pin
Connector
Cap or insulate if
not being used
3.5MM SWC CABLE
Plug in the 3.5MM SWC cable to the 4-pin port
on the module. See “DIP SWITCH SETTINGS” section.
Audio Input
Rear Camera (IO3)
LIN BUS (Green/Black)
Antenna Adapter
(Included)
24-Pin
Connector
8-Pin
Connector
NON
BOSE
10-Pin
Connector SWC DIP SWC
1 2 3 4
ON
Chime Volume
Adjustment
1 2 3
ON VR Activation
for OnStar (set DIP#1 to ON)
JVC/Kenwood (Blue / Yellow)
Crux Interfacing Solutions • Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.071720
SOOGM-19L
OnStar Radio Replacement Interface with Steering Wheel
Control Retention for GM LAN v2 (LIN) Bus Vehicles 2014 - 2018
2 of 4
RAD IO REP LA CEMENT
SWC RET ENTIO N
+
R
INTERFACING SOLUTIONS
Plug in the 8-pin Molex connector of the SOOGM-19L harness
to the Black, NON BOSE, port of the module.
Non-Bose
Port
The SOOGM-19L has a potenometer to adjust the chime
volume. It is set at half way by default. To adjust the volume,
simply use a suitable screw driver and turn the potenometer
clockwise to increase the volume and counter-clockwise to
decrease the volume.
Chime
Volume
Adjustment
CHIME VOLUME ADJUSTMENT:
ONSTAR VOLUME ADJUSTMENT:
To adjust the OnStar volume, turn on OnStar and adjust the volume using the SWC volume adjustment. There
are 4 steps of volume control. Once it is set, the SOOGM-19L will memorize this level.
AUDIO CONNECTION:
BOSE AMPLIFIER BYPASS:
For vehicles equipped with a factory Bose amplier, extend the speaker wires of the SOOGM-19L harness and
connect to the Bose amplier output wires. Locate the Bose amplier to nd out how much speaker wires is
neccessary. The Bose amplier is located as follows: (NOTE: Bose ampliers are commonly found in the locaons listed
below but the manufacturer can mount it elsewhere. Installer should verify the locaon before installaon.)
Trucks = Center of the rear wall / SUVs = Center console or in the cargo space / Sedans = Rear deck or Trunk area
Pinout for the 8 and 16 pin OEM Bose amplier connectors:
14
8 5
1
8
9
16
Pin # Wire Color Descrip�on
1 Dark Blue / Grey Subwoofer +
2 Yellow Right Front Speaker +
3 Dark Blue Le� Front Speaker +
4 Red / Yellow Constant +12V
5 Grey / Black Subwoofer -
6 Yellow / Black Right Front Speaker -
7 Brown / Dark Blue Le� Front Speaker -
8 Black Ground
Pin # Wire Color Descrip�on
4 Brown / Light Green Right Front Tweeter +
5 Yellow / Dark Blue Tweeter +Le� Front
6 White Right Rear Speaker +
7 Light Green Le� Rear Speaker +
12 Purple / Brown Right Front Tweeter -
13 Yellow / Grey Tweeter - Le� Front
14 Dark Blue / Black Right Rear Speaker -
15 Light Green / Black Le� Rear Speaker -
Crux Interfacing Solutions • Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.071720
SOOGM-19L
OnStar Radio Replacement Interface with Steering Wheel
Control Retention for GM LAN v2 (LIN) Bus Vehicles 2014 - 2018
3 of 4
RAD IO REP LA CEMENT
SWC RET ENTIO N
+
R
INTERFACING SOLUTIONS
4. Unplug the GREEN and GRAY
connectors from the headunit.
5. Plug the GREEN and GRAY connectors to the
SOOGM-19L T-Harness.
6. Use the supplied antenna adapter to plug
between the OE antenna connector and
aermarket radio antenna port.
7. Remove plasc trim under the
steering wheel column and locate a
GREEN/BLACK wire in the bundle. Tap
the GREEN/BLACK from the SWC Cable.
We recommend soldering the wires
together for a reliable connecon.
8. Use a dash kit (not included) for a clean
install. Test the radio for funconality. Test
the chime and Retained Accessory Power
(RAP) funcons. Reverse the process to
install the new aermarket radio.
The SOOGM-19L is prewired with an RCA connector to retain the OEM camera on vehicles
with a IO3 system. To retain the OEM camera on IO4, IO5 and IO6 systems, you will need
connect an RCA cable to the 12-pin connector on the HMI module found either by the
passenger kick panel or behind the glove box. Connect the RCA as follows:
HMI Connector
PIN 5 = Gray/Yellow to RCA posive
PIN 6 = White/Blue to RCA shield
We recommend soldering and heat shrinking these wires for a secure connecon.
Pin 6 Pin 5
White/Blue Gray/Yellow
OEM CAMERA RETENTION:
INSTALLATION INSTRUCTIONS:
1. Connect the aermarket radio’s
power/speaker harness to the SOOGM-
19L T-Harness using the Installaon
Diagram on page 1. Use good quality
crimp caps or bu splice for a secure
connecon. Solder and heat shrinking
the connecons is highly recommended.
2. Carefully remove the radio trim with a plasc
pry tool and pull outward.
3. Remove the radio bezel by removing the
4 screws on the corners.

Tuotetiedot

Merkki: CRUX
Kategoria: Ei luokiteltu
Malli: SOOGM-19L

Tarvitsetko apua?

Jos tarvitset apua merkille CRUX SOOGM-19L esitä kysymys alla ja muut käyttäjät vastaavat sinulle




Ei luokiteltu CRUX Käyttöohjeet

CRUX

CRUX SWRFD-60B Käyttöohje

16 Lokakuuta 2024
CRUX

CRUX SOOGM-16K Käyttöohje

16 Lokakuuta 2024
CRUX

CRUX SOCGM-17B Käyttöohje

16 Lokakuuta 2024
CRUX

CRUX DKGM-49 Käyttöohje

16 Lokakuuta 2024
CRUX

CRUX DKGM-C2S Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX DKVW-21 Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX SOHTL-20 Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX AVIGM-04S Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX SOCVW-21 Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX AUX-MB1 Käyttöohje

15 Lokakuuta 2024

Ei luokiteltu Käyttöohjeet

Viimeisimmät Ei luokiteltu Käyttöohjeet