CRUX VRFBM-77C Käyttöohje

CRUX Ei luokiteltu VRFBM-77C

Lue alta 📖 käyttöohje suomeksi merkille CRUX VRFBM-77C (12 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 3 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/12
With OE type Dynamic Parking Guide Lines
On-screen display and setup
2 trigger outputs (+12V max. 1A), separately adjustable switching events (CAN, ACC,
rear-view camera, reverse gear)
Rear-view camera input
Front camera input
Front camera input can also be used as an Auxiliary Video Input
Automac switching to rear-view camera input on engagement of reverse gear from all
operaon modes
Forced rear-view camera opon (only on vehicles with PDC buon)
Manual return from rear-view and front camera (cancellaon of automac switching)
Picture-in-picture mode combining aer-market rear-view and front camera picture(s)
with factory parking sensor graphics
Compable wi all factory video accessories (e.g. rear-view camera, DVD-changer, etc.) th
Plug & Play installaon
For the F-series BMW with navigaon system or radio and 6.5”, 7”, 8.8” or 10.25”
monitor with 4+2pin HSD2 LVDS connector
On i3 installaons, part# HAR-i3 is required to install the interface. The interface module
is installed/mounted under the rear seat and you will need to run the HAR-i3 towards
the rear seat.
BM-77C Module
BM-77C Harness
4+2 PIN HSD2 LVDS Cable
Power/CAN Harness
1 / 12
rev.122617
2 / 12
rev.122617
Seng the DIP switches of the Interface B . ox
DIPs 1 and 2 on the back of the interface-b used to set the monitor size. DIP 3 must be set to OFF.ox is
Vehicle/ Navigaon
Dip 1
Dip 2
6.5“ monitor.
OFF
OFF
7“ monitor
OFF
OFF
8.8“ monitor
ON
OFF
10.25“ monitor (ver.1)
ON
OFF
10.25“ monitor (ver.2)
ON
ON
Aer each change of the DIP switch sengs you have to execute a power reset of the interface box!
Note: The interface is installed on the backside of the head unit and needs a constant +12V power source.
Connecng Interface box a harnesses nd
Remove the female Quadlock connector of the vehicle harness from the rear of the navigaon
computer.
Remove opcal leads from the female Quadlock connector of the vehicle harness and insert them into
the female Quadlock connector of -77C harness at the same posion. BM
Connect the female Quadlock connector of vehicle harness to the male Quadlock connector of
the -77C harness. BM
1
2
3
BM-77C
HARNESS
3 / 12
rev.122617

Tuotetiedot

Merkki: CRUX
Kategoria: Ei luokiteltu
Malli: VRFBM-77C

Tarvitsetko apua?

Jos tarvitset apua merkille CRUX VRFBM-77C esitä kysymys alla ja muut käyttäjät vastaavat sinulle




Ei luokiteltu CRUX Käyttöohjeet

CRUX

CRUX DKGM-C2S Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX DKVW-21 Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX SOHTL-20 Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX AVIGM-04S Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX SOCVW-21 Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX AUX-MB1 Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX SWR-A Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX AUX-MB2 Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX DKGM-C2D Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX RVCHN-76C Käyttöohje

15 Lokakuuta 2024

Ei luokiteltu Käyttöohjeet

Viimeisimmät Ei luokiteltu Käyttöohjeet