CRUX VRFBM-77i Käyttöohje

CRUX Ei luokiteltu VRFBM-77i

Lue alta 📖 käyttöohje suomeksi merkille CRUX VRFBM-77i (11 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 4 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/11
BMW
2015 2016 i3*
With OE type Dynamic Parking Guide Lines
On-screen display and setup
2 trigger outputs (+12V max. 1A), separately adjustable switching events (CAN, ACC rear-view camera, ,
reverse gear)
Rear-view camera input
Front camera input
Front camera input can also be used as an Auxiliary Video Input
Automac switching to rear-view camera input on engagement of reverse gear from all operaon modes
Forced rear-view camera opon (only on vehicles with PDC buon)
Manual return from -view and front camera (cancellaon of automac switching) rear
Picture- -picture mode combining aer-market rear-view and front camera picture(s) with factory parking in
sensor graphics
Compable with all factory video accessories (e.g. rear-view camera, -changer, etc.) DVD
Plug & Play installaon
For the BMW i3 with navigaon system or radio and 6.5”, 7”, 8.8” or 10.25” monitor with 4+2pin HSD2
LVDS connector
The interface is installed under the glove compartment and the radio headunit is located under the rear
seat.
BM-77i Module
BM-77i Harness
4+2 PIN HSD2 LVDS Cable
Power/CAN Harness
i3-HAR
1 / 11
Rev.1128 16
Rev.1128 16
Seng the DIP switches of the Interface B . ox
DIPs 1 and 2 on the back of the interface-b used to set the monitor size. DIP 3 must be set to OFF.ox is
Vehicle/ Navigaon
Dip 1
Dip 2
Dip 3
6.5“ monitor.
OFF
OFF
No funcon
7“ monitor
OFF
OFF
No funcon
8.8“ monitor
ON
OFF
No funcon
10.25“ monitor (ver.1)
ON
OFF
No funcon
10.25“ monitor (ver.2)
ON
ON
No funcon
Aer each change of the DIP switch sengs you have to execute a power reset of the interface box!
Connecng Interface box a harnesses nd
Remove the rear seat and locate the Radio Headunit. Unplug the Quadlock connector from the Radio
Headunit.
Plug factory Quadlock connector into the BM-77i T-harness female Quadlock connector
Connect the male Quadlock connector of the BM-77i T-harness to the female Quadlock connector o f
the Radio Headunit.
Run the i3-HAR along the passenger side door sill from the Radio Headunit towards the glove
compartment and plug it into the Power/CAN harness .
Connect the female 12pin AMP connector of the Power/CAN harness to the front side of the - VRFBM 77i
interface box.
3 / 12
Rev.1128 16
1
2
3
4
5

Tuotetiedot

Merkki: CRUX
Kategoria: Ei luokiteltu
Malli: VRFBM-77i

Tarvitsetko apua?

Jos tarvitset apua merkille CRUX VRFBM-77i esitä kysymys alla ja muut käyttäjät vastaavat sinulle




Ei luokiteltu CRUX Käyttöohjeet

CRUX

CRUX DKGM-C2S Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX DKVW-21 Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX SOHTL-20 Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX AVIGM-04S Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX SOCVW-21 Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX AUX-MB1 Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX SWR-A Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX AUX-MB2 Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX DKGM-C2D Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX RVCHN-76C Käyttöohje

15 Lokakuuta 2024

Ei luokiteltu Käyttöohjeet

Viimeisimmät Ei luokiteltu Käyttöohjeet