CRUX WVITY-01 Käyttöohje

CRUX Ei luokiteltu WVITY-01

Lue alta 📖 käyttöohje suomeksi merkille CRUX WVITY-01 (6 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 4 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/6
R
INTERFACING SOLUTIONS
A/V
SERIES
Crux Interfacing Solutions • Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.031221
WVITY-01
Wi Connectivity Integration
for Select Lexus, Scion and Toyota Vehicles
1 of 6
- Enables wireless (Wi-Fi) Audio/Video mirroring from mobile devices to the OEM screen.
- Provides an audio/video input which can also be used to add a camera.
- Includes a USB input to play audio and video les.
- Provides a virtual remote control via a smartphone wi connection.
- Dual band (5GHz and 2.4GHz) Wi capability for clear connection.
- Includes HMDI output for high quality video.
- Works with Facetime, Maps, Skype, YouTube, and other apps.
PRODUCT FEATURES:
PARTS INCLUDED:
WORKS WITH:
WVITY-01 Vehicle Harness WVI-H Module Power Harness
Dual Antennas WiFi AV Out Harness AV In / Video Out Harness
IR Extension
iOS 7 and Newer OS 4.2 and Newer
Crux Interfacing Solutions • Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.0312212 of 6
WVITY-01
Wi Connectivity Integration
for Select Lexus, Scion and Toyota Vehicles
Wi-Fi
INTERFACE
SEEK
AUDIO
TRACK
PWR VOL
2-PIN
SWC PLUGS
ORANGE/WHITE
WIRE
GROUND
OPTIONAL SWITCH
(Not Included) This toggle switch option
is for vehicles that do not
have Steering Wheel Controls.
28-PIN
16-PIN
10-PIN
1 2 3
ON
1 2 3
ON
DIP SWITCHES
SHOULD
BE ALL OFF”
HDMI OUTPUT
A/V INPUT
BLUE = A/V TRIGGER*
RED = +12V ACC
BLACK = GROUND
*Connect BLUE A/V Trigger
to +12V to toggle A/V INPUT
A/V Extension
Cable
Video Out
(to extension monitors)
Video Input (or Camera)
Right Audio Input
Left Audio Input
USB Input
INSTALLATION DIAGRAM:
NOTE: The 16-Pin connector is not available on some newer vehicles. You can leave it disconnected if your
vehicle does not have a 16-Pin connector.
INSTALLATION INSTRUCTIONS:
THE AV INTERFACE:
1. Remove the factory radio from the dashboard.
Note: DO NOT disconnect the airbag connector.
2. Remove the factory connectors from behind the factory radio.
3. Mate the T-Harness connecons to the factory connectors. (Make sure all connectors are properly seated
into the interface and into the radio.) (JBL Radios see page 3)
4. Connect the Orange/White wire to your corresponding SWC type. (9-Buon or 5-Buon)
R
INTERFACING SOLUTIONS
A/V
SERIES
1. Connect the 18-Pin power/video cable to the Wi-Fi Interface module.
2. Connect the antenna leads to the module.
3. Connect the RED power lead to +12V ACC and the BLACK wire to Ground.
4. Connect the BLUE A/V Input wire to +12V to trigger the oponal A/V input feature. The video input can also be
connected to a camera source instead. A toggle switch (not included), wired between the BLUE wire and +12V
can be used to switch ON or OFF the A/V input feature.
5. If the USB input feature will be used, you can use the virtual remote control on your smartphone to control the
USB funcons. See VIRTUAL REMOTE secon for details. Extended a USB cable to an easily accessible locaon.
6. Plug in the Composite RCA output of the WVI-H harness to the WVITY-01 AV input.
7. Test for funconality.
Crux Interfacing Solutions • Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.0312213 of 6
WVITY-01
Wi Connectivity Integration
for Select Lexus, Scion and Toyota Vehicles
SETTING YOUR DEVICE:
With the WVI-H module ON and READY:
For iOS devices:
Open sengs > Select > UnderWi-Fi
‘Choose Network’ “Crux WiFi ***” Select
Aer connecng to Crux Wi, select
“SCREEN MIRRORING” from the Control
Center and tap Crux Wi ***. To access
Control Center, on iPhone X, pull down
from the upper right corner of the screen,
on other iPhone models, pull up from the
boom of the screen.
THE WIFI INTERFACE:
10-PIN JBL RADIOS
Vehicles equipped with a JBL system will not have a 10-Pin connector, you will need to cut three wires from the
10-pin male connector (with female pins) of the WVITY-01 T-harness and connect as follows:
R
INTERFACING SOLUTIONS
A/V
SERIES
NOTES:
1. Does not support Nelix and any DRM protected
les on iOS devices due to Restricons by Apple.
RED = to 12V ACC
YELLOW = to 12V Constant
BLACK = to Ground

Tuotetiedot

Merkki: CRUX
Kategoria: Ei luokiteltu
Malli: WVITY-01

Tarvitsetko apua?

Jos tarvitset apua merkille CRUX WVITY-01 esitä kysymys alla ja muut käyttäjät vastaavat sinulle




Ei luokiteltu CRUX Käyttöohjeet

CRUX

CRUX SWRFD-60B Käyttöohje

16 Lokakuuta 2024
CRUX

CRUX SOOGM-16K Käyttöohje

16 Lokakuuta 2024
CRUX

CRUX SOCGM-17B Käyttöohje

16 Lokakuuta 2024
CRUX

CRUX DKGM-49 Käyttöohje

16 Lokakuuta 2024
CRUX

CRUX DKGM-C2S Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX DKVW-21 Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX SOHTL-20 Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX AVIGM-04S Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX SOCVW-21 Käyttöohje

15 Lokakuuta 2024
CRUX

CRUX AUX-MB1 Käyttöohje

15 Lokakuuta 2024

Ei luokiteltu Käyttöohjeet

Viimeisimmät Ei luokiteltu Käyttöohjeet