D-Link DSN-2100 Käyttöohje

Lue alta 📖 käyttöohje suomeksi merkille D-Link DSN-2100 (24 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 3 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/24
iSCSI SAN ARRAY
WITH 8 SATA BAYS
Quick Installation Guide+
Installations-Anleitung+
Guide d’installation+
Guía de instalación+
Guida di Installazione+
2
Quick Installation Guide
DSN-2100
DSN-2100 CD ROM
If any of the items are missing, please contact your reseller.
iSCSI SAN ARRAY WITH 8 SATA BAYS
Package Contents
Power
cables
Console
cable
Keys Screws
Connect to DSN Series SAN Array
Example of Connecting to DSN Series SAN Array Rear Panel
C. The management port can be connected to the server either by directly attaching a crossover
cable, or via a switched infrastructure using a standard Ethernet cable. Facing the rear of
the SAN array, the management port is on the right side of the I/O panel. By default, this port
is set to the IP address of . This can be changed using the web based wizard. 192.168.1.1
D. The diagnostic port can optionally be used for diagnostics. It connects to an RS-232C port
on your host computer congured for a baud rate of 9600bps at eight data bits, no parity bit,
one stop bit and no hardware handshake, using a standard DB9 cable.
A. To install the hard drives:
Place the hard drives into the drive trays and secure with mounting screws on the drive
trays. Then gently insert the assembled drive trays into the enclosure until the latch clicks.
B. Attach an Ethernet cable to 1GbE data port 0 on the rear panel and to your server or SAN
switch. Facing the rear of the SAN array, the data ports are on the left side. To connect
additional data ports to your SAN array, repeat this step using another Ethernet cable and
the next data port.
Rack mount
slide rails
3
Prepare Your Server
A. This guide assumes that Microsoft Windows 2003 Server or later will be used for product set
up. The server must have a 10/100/1000 Gbps NIC. All updates, Service Packs, and drivers
for the operating system and NIC must be installed. Your server will need to install the latest
supported version of Microsoft iSCSI initiator software. The software can be downloaded
from http://www.microsoft.com/downloads
B. Your server will need to install the latest supported version of Java Runtime Environment 6
(JRE 6) or later version. The Java software is available at: http://java.com
C. The DSN series SAN array management port has an IP address of 192.168.1.1. Therefore,
the NIC of your server must have a xed IP address of 192.168.1.x (e.g., 192.168.1.2). After
you set up the SAN array via the web-based wizard, you can change the management port
to the desired IP address.
Note: Attempting to install the Java Runtime Environment 6 on a non supported version of
Windows or a computer whose Service Packs are out of date will display an error
message.
First-Time Startup
A. Power up the SAN array. The system will start to boot:
The left (Power) LED turns green when power is applied.
The SAN array goes through its power-on procedure, which takes up to ve minutes, after which
the right (Ready/Fault) LED turns green.
B. Point your Web browser on the management computer to the following default IP address:
192.168.1.1
C. When the Start-up Wizard’s Welcome screen appears, click the
I Accept the End User License Agreement” button.
D. At the Administrator Account screen, enter a case-sensitive password for the administrator
account, if you wish to change the default value. The default username is and the default admin
password is . Click .admin Next
E. At the Management Port screen, enter the IP address, subnet mask, and default gateway that
computers will use to access the management port. Change the host name if desired. Click
Next.
F. At the Data Port screen, enter the IP address, subnet mask, and default gateway for each iSCSI
data port. You can skip any or all of these items, and assign them later. Click or “Next Skip To
Email Notication”.
G. At the Email Notication screen, enable email notications. Enter an SMTP server IP address
and port number, return email address, and email address where alerts are to be sent. Click
Next.
H. Review your settings. Use the button to change any settings that need to be edited. Then Back
click and wait for the system to restart. You are now ready to use your SAN array.Finish
Note: For more information about the system setting, please refer to the Software User’s Guide.

Tuotetiedot

Merkki: D-Link
Kategoria: Ei luokiteltu
Malli: DSN-2100

Tarvitsetko apua?

Jos tarvitset apua merkille D-Link DSN-2100 esitä kysymys alla ja muut käyttäjät vastaavat sinulle




Ei luokiteltu D-Link Käyttöohjeet

D-Link

D-Link DWL-R60AT Käyttöohje

11 Tammikuuta 2025
D-Link

D-Link ANT24-0800 Käyttöohje

4 Tammikuuta 2025
D-Link

D-Link DWL-P200 Käyttöohje

4 Tammikuuta 2025
D-Link

D-Link ANT24-1400 Käyttöohje

4 Tammikuuta 2025
D-Link

D-Link DCS-71 Käyttöohje

4 Tammikuuta 2025
D-Link

D-Link KVM-121 Käyttöohje

4 Tammikuuta 2025
D-Link

D-Link KVM-403 Käyttöohje

4 Tammikuuta 2025
D-Link

D-Link KVM-401 Käyttöohje

4 Tammikuuta 2025

Ei luokiteltu Käyttöohjeet

Viimeisimmät Ei luokiteltu Käyttöohjeet