Extron DA HD 8K L Käyttöohje

Extron Vastaanotin DA HD 8K L

Lue alta 📖 käyttöohje suomeksi merkille Extron DA HD 8K L (2 sivua) kategoriassa Vastaanotin. Tämä opas oli hyödyllinen 4 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Lataa PDF
Sivu 1/2
1
DA4 HD 8K L and DA6 HD 4K L • Setup Guide
IMPORTANT NOTE:
Go to www.extron.com for the complete user guide, installation instructions, and specications before connecting
the product to the power source.
This guide provides basic instructions for an experienced technician to install the DA HD 8K L distribution ampliers.
Overview
The Extron DA4 HD 8K L and DA6 HD 8K L distribution ampliers distribute one HDMI input signal to four or six outputs
simultaneously at resolutions up to 8K @ 30 Hz 4:4:4 or 8K @ 60 Hz 4:2:0, and comply with HDMI 2.1 and HDCP 2.2. The DAs also
feature EDID Minder® Plus, remote control and monitoring via Ethernet, USB, or RS-232, and discrete display control via CEC.
For complete instructions, see the DA HD 8K L Series User Guide at www.extron.com.
Front Panel
DA4 HD 8K L
CONFIG
INPUT 1
SIGNAL
HDCP
e
2 3 4
OUTPUTS
DA6 HD 8K L
CONFIG
INPUT 1
SIGNAL
HDCP
e
2 3 4 5 6
OUTPUTS
A
A
A
A
A
A C
C
C
C
C
CB
B
B
B
B
B D
D
D
D
D
D
A — Lights when power is applied to the unit.Power status LED
B USB-C Config port — Connect a PC to this port to configure and monitor the DA via Simple Instruction Set (SIS™ ™) or
Product Configuration Software (PCS).
C — Input LEDs
• Signal LED — Lights when a TMDS signal is detected on the HDMI input. If the source requires HDCP encryption, this LED
may light only when HDCP is authenticated.
• HDCP LED — Lights when the source requires HDCP encryption and it has been authenticated with the HDMI input.
D — Outputs LEDs
• HDCP LEDs — Light when HDCP is authenticated between a DA output and the corresponding sink device.
• Signal LEDs — Light when HPD is detected from the corresponding sink device and a TMDS signal is detected at the
input.
Rear Panel
POWER
12V
--A MAX 21 43
INPUT
REM O T E
OUTPU T S
LAN
RS-232
T x R x G
R
POWER
12V
--A MAX 21 63 4 5
INPUT
REM O T E
OUTPU T S
LAN
RS-232
T x R x G
R
D
D
D
D
D
D
A
A
A
A
A
A B
B
B
B
B
BE
E
E
E
E
E F
F
F
F
F
F
C
C
C
C
C
C
A Power input — Connect the provided 12 VDC, 3.0 A power supply to this 2-pole 3.5 mm captive screw port (see the power
Attention and diagram to wire the connector on ).page 2
2
68-3435-50 Rev. A
08 24
SECTION A–A
Ridges
Smooth
A
A
3/16"
(5 mm) Max.
POWER
12V
--A MAX ATTENTION:
• Do not connect the power supply before reading the
Attention in the Power Supply section of the DA HD 8K L
Series User Guide.
• Ne branchez pas la source d’alimentation externes
avant d’avoir lu les mises en garde dans la section
« Power Supply » du DA HD 8K L Series User Guide.
B (see on page 1HDMI input Rear Panel ) — Connect a source device to this female HDMI type A input.
C HDMI outputs — Connect up to four or six display devices to these female HDMI type A outputs.
D Remote RS-232 port — Connect the provided 3-pole captive screw connector for SIS configuration, monitoring, and firmware
updates (Pin 1 = Tx, Pin 2 = Rx, Pin 3 = Ground). Protocol: 9600 baud, 8 data bits, 1 stop bit, no parity.
E LAN port — Connect to an Ethernet LAN or WAN via this RJ-45 port to control the DA from a remote location. When connected
to an Ethernet LAN or WAN, the DA can be accessed and operated from a computer with a standard internet browser.
Ethernet connection indicators — The Link and Activity LEDs indicate the status of the Ethernet connection.
• Green Link LED — Indicates the distribution amplier is properly connected to an Ethernet LAN. This LED lights steadily.
• Amber Activity LED — Indicates transmission of data packets on the RJ-45 port. This LED ickers as the distribution
amplier communicates.
F Reset button — Use an Extron Tweeker or small screwdriver to press and hold the button while the DA is running or while
powering up, for different reset levels.
• Press and hold the reset button while applying power to revert to factory default rmware for a single power cycle, but
maintain IP settings.
• Press and hold the reset button for 3 seconds and again for <1 second within 1 second to reset the unit to factory settings.
• Press and hold the reset button for 6 seconds and again for <1 second after the LED blinks twice to reset all IP settings
back to factory defaults.
• Press and hold reset button for 9 seconds and again for <1 second after the LED blinks 3 times to reset all settings to
default except the rmware.
Installation
1. Mount the DA in a suitable location with one of the recommended mounting kits (see www.extron.com for mounting options).
Follow the instructions provided with the mounting kit.
2. If required, connect a control PC to the USB-C Cong port (see Front Panel,
B on page 1), Remote RS-232 port (see Rear
Panel, D, see the diagram below for wiring), or LAN port (E, see the diagram below, right for wiring).
RS-232
Tx Rx G
REMOTE
TransmitReceive
ReceiveTransmit
GroundGround
DB9 Pin Locations
Female
5 1
9 6
Pin 2 = Rx
Pin 3 = Tx
Pin 5 = G
Computer DA HD 8K
NOTE: Use PCS to congure EDID Minder, mute the video signal, mute the
audio signal, adjust the video color bit depth, or monitor the signal and
HDCP status (see the DA HD 8K L Series Help File).
3. Connect the display devices to the rear panel HDMI outputs (see Rear Panel,
C)
and power them on.
123 45678
RJ-45 Connector
Insert Twisted
Pair Wires
Pins:
Pin
1
2
3
4
5
6
7
8
Wire color
White-green
Green
White-orange
Blue
White-blue
Orange
White-brown
Brown
Wire color
T568A T568B
White-orange
Orange
White-green
Blue
White-blue
Green
White-brown
Brown
4. Connect the source device to the rear panel HDMI input (
B).
NOTE: Use the LockIt® HDMI cable lacing brackets provided to secure the HDMI connectors.
5. Connect the provided 12 VDC, 3.0 A power supply to the 2-pole captive screw inlet (
A, see the diagram at the top of the page
to wire the connector).
6. Power on the source device.
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the Extron
Safety and Regulatory Compliance Guide on the Extron website.
© 2024 Extron — All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

Tuotetiedot

Merkki: Extron
Kategoria: Vastaanotin
Malli: DA HD 8K L

Tarvitsetko apua?

Jos tarvitset apua merkille Extron DA HD 8K L esitä kysymys alla ja muut käyttäjät vastaavat sinulle


Vastaanotin Extron Käyttöohjeet

Extron

Extron DA2 HD 8K AI Käyttöohje

10 Maaliskuuta 2025
Extron

Extron MDA 3A Käyttöohje

16 Lokakuuta 2024
Extron

Extron DTP HDMI 4K 230 RX Käyttöohje

16 Lokakuuta 2024
Extron

Extron MPA 401-70V Käyttöohje

16 Lokakuuta 2024
Extron

Extron MPA 401-100V Käyttöohje

16 Lokakuuta 2024
Extron

Extron SW2 VGA DA2 A Käyttöohje

16 Lokakuuta 2024
Extron

Extron P/2 DA2xi MT Käyttöohje

16 Lokakuuta 2024
Extron

Extron MTP DA8 Käyttöohje

16 Lokakuuta 2024
Extron

Extron P/2 DA8 Käyttöohje

16 Lokakuuta 2024
Extron

Extron MDA 3SVA Käyttöohje

16 Lokakuuta 2024

Vastaanotin Käyttöohjeet

Viimeisimmät Vastaanotin Käyttöohjeet

Yamaha

Yamaha Aventage RX-A4A Käyttöohje

9 Huhtikuuta 2025
Yamaha

Yamaha Aventage RX-A8A Käyttöohje

9 Huhtikuuta 2025
Phonocar

Phonocar PH544 Käyttöohje

5 Huhtikuuta 2025
DJI

DJI D-RTK 3 Käyttöohje

4 Huhtikuuta 2025
Harper

Harper HDT2-5010 Käyttöohje

2 Huhtikuuta 2025
Harper

Harper HDT2-2010 Käyttöohje

2 Huhtikuuta 2025
QSC

QSC SPA-Qf 60x2 Käyttöohje

1 Huhtikuuta 2025
Streacom

Streacom TL1 Käyttöohje

30 Maaliskuuta 2025
Graupner

Graupner GR-8 Käyttöohje

30 Maaliskuuta 2025
MB Quart

MB Quart FA2-2000.1 Käyttöohje

29 Maaliskuuta 2025