Festo EAHT-E9-FB-3D-30 Käyttöohje

Festo Ei luokiteltu EAHT-E9-FB-3D-30

Lue alta 📖 käyttöohje suomeksi merkille Festo EAHT-E9-FB-3D-30 (1 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 5 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/1
Assembly instructions (Original instructions)
8079181
2017-09a
[8079183]
†‡
Mounting kit
EAHT-E9-FB-3D-30
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
+49 711 347-0
www.festo.com
1. Further applicable documents
All available documents for the product www.festo.com/pk
Observe further applicable documents:
Description of the planar surface gantry 4 and actuator 5
Assembly instructions of profile mounting attachment 6 and
connection kit 7
2. Safety
Switch off power supply before mounting work.
Comply with tightening torques ( Table).
3. Intended use
Mounting of a Z-axis 5 to the Y-axis of the planar surface gantry 4.
4. Additional information
Centring sleeve (B) www.festo.de/catalogue
5. Scope of delivery
2227
6d_1 1 Mounting kit
2 Screw
3 Cylindrical
dowel pin
(1x)
(2x)
(2x)
6. Not in scope of delivery
2227
6d_2 4 Planar surface
gantry
EXCM-30
(1x)
2227
6d_3 5 Z-axis1)
DGSL-8/-10/-12
EGSC-25/-32
2)
EGSK-20/-26
EGSL-35
(1x)
2227
6d_4 6 Profile mounting
attachment
EAHF-L2-25-P
7 Connection kit
EAHT-AE-3D
(1x)
(1x)
7. Mounting
7a. Interface to planar surface gantry 4
4
4
44
22276d_5
Place the mounting kit 1
with cylindrical dowel
pins 3 at slide unit (A)
of the Y-axis of the planar
surface gantry 4.
Tighten the screws 2.
7b. Interfaces of Z axis 5
5
5
55
Mounting components and tightening torques ( Table).
For DGSL-8/-10
22276d_6
Position centring sleeves (B).
Position of Z-axis 5 1 on the mounting kit .
Tighten the screws (C).
For DGSL-12
22276d_7
Position centring sleeves (B).
Position of Z-axis 5 1 on the mounting kit .
Tighten the screws (C).
1 2
1) Mounting components are not included in the scope of delivery of Z-axis 5.
2) In case of EGCS-25/-32 with a stroke of 25, mounting is not possible.
For EGSC-25
22276d_13
Place the profile mounting attachments 6 along the Z-axis 5 ( Further
applicable documents).
Position of Z-axis 5 1 on the mounting kit .
Mount the profile mounting attachments 6 to the mounting kit 1 with
the screws (C).
For EGSC-32
22276d_12
Place the profile mounting attachments 6 along the Z-axis 5 ( Further
applicable documents).
Position of Z-axis 5 1 on the mounting kit .
Mount the profile mounting attachments 6 to the mounting kit 1 with
the screws (C).
For EGSK-20
22276d_9
Position of Z-axis 5 1 on the mounting kit .
Tighten the screws (C).
3)
3) Tolerances for tightening torques MA without specification of tolerance
MA = 1.2 Nm: ± 10 %
MA , 1.2 Nm: ± 20 %
For EGSK-26
22276d_10
Position of Z-axis 5 1 on the mounting kit .
Tighten the screws (C).
For EGSL-35
22276d_8
Position centring sleeves (B).
Position of Z-axis 5 1 on the mounting kit .
Tighten the screws (C).
7c. Interface to connection kit 7
7
7
77
2227
6d_1
1
Observe assembly
instructions for connection
kit 7 ( Further applicable
documents).
8. Screw sizes and tightening torques M
A
3)
EAHT-E9- 2
2
2
22 [Nm]
FB-3D-30 M4x10 2.5
Not in scope of delivery:
Z-axis 5
5
5
55 Centring sleeve (B) (C) Screw ISO 4762 [Nm]
DGSL-8/-10 ZBH-7 (2x) M4x10-8.8 (2x) 2.0
DGSL-12 ZBH-7 (2x) M5x12-8.8 (2x) 3.0
EGSC-25/-32 M4x8-8.8 (4x) 2.0
EGSK-20 M3x6-8.8 (4x) 1.2
EGSK-26 M4x6-8.8 (4x) 2.5
EGSL-35 ZBH-7 (2x) M4x12-8.8 (4x) 2.5
9. Prior to commissioning
Note
Collision!
The mounting kit reduces the available Y-stroke of the planar surface
gantry 4 by 16 mm.
Check Z-axis 5 for collision.
Set the end stops of the Y-axis at the planar surface gantry 4 ( Further
applicable documents).
4
1
3
2
4
3
1
A
7
1
7
1
5
B
C
1
5
B
C
1
5
B
C
2
6
5
1
5
C
6
1
5
C
6
1
5
C
1
5
C

Tuotetiedot

Merkki: Festo
Kategoria: Ei luokiteltu
Malli: EAHT-E9-FB-3D-30

Tarvitsetko apua?

Jos tarvitset apua merkille Festo EAHT-E9-FB-3D-30 esitä kysymys alla ja muut käyttäjät vastaavat sinulle




Ei luokiteltu Festo Käyttöohjeet

Ei luokiteltu Käyttöohjeet

Viimeisimmät Ei luokiteltu Käyttöohjeet