Festo PAML-CP-90-HP3-G12 Käyttöohje

Festo Ei luokiteltu PAML-CP-90-HP3-G12

Lue alta 📖 käyttöohje suomeksi merkille Festo PAML-CP-90-HP3-G12 (2 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 2 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/2
PAML-CP/-MB/-MK-90
Sub-base/Mounting bracket/Module connector
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Deutschland
+49 711 347-0
www.festo.com
Assembly instructions
8161942
2021-10b
[8161944]
Translation of the original instructions
© 2021 all rights reserved to Festo SE & Co. KG
1 Applicable documents
All available documents for the product
è www.festo.com/sp.
2 Safety
2.1 Safety instructions
Only use the product in its original condition without unauthorised modifica-
tions.
Only use the product if it is in perfect technical condition.
Take the weight of an individual device or a service unit into account.
Dependent on the design, a mounted service unit can weigh more than 50 kg.
Under intended use the surface temperature may reach 60 °C. Allow the device
to cool down before working on it.
Make sure the mounting surface is sufficiently strong for the maximum forces.
Only use suitable mounting components.
Mount the individual device or the service unit only on flat surfaces.
2.2 Intended use
The sub-base PAML-CP serves as an adapter for the pneumatic connection and
for pipe mounting for in-line installation of service units.
The mounting bracket PAML-MB is used for connection and wall mounting of
individual devices or service units.
The module connector PAML-MK is used to connect two service units of the
same size.
2.3 Training of qualified personnel
Work on the product may only be carried out by qualified personnel who can eval-
uate the work and detect dangers. Personnel must have the relevant mechanical
training.
3 Additional Information
Accessories è www.festo.com/catalogue.
4 Product Range Overview
4.1 Scope of delivery
2
1
3
4
5
Fig. 1: Sub-base PAML-CP-90-HP3-G12
1
Front plate (1x)
2
Rear plate (1x)
3
Screw (8x)
4
Washer (8x)
5
O-ring (2x)
6
7
8
Fig. 2: Sub-base PAML-CP-90-HP3-G114
6
Front plate (1x)
7
Rear plate (1x)
8
O-ring (2x)
9
10
11
12
13
141516
Fig. 3: Mounting bracket PAML-MB-90-HP3
9
Wall bracket (1x)
10
O-ring (1x)
11
Front plate (1x)
12
Screw (2x)
13
Rear plate (1x)
14
Sleeve (2x)
15
Screw (2x)
16
Retaining screw (1x)
17
18
19
20
Fig. 4: Module connector PAML-MK-90-HP3
17
Screw (2x)
18
Front plate (1x)
19
O-ring (1x)
20
Rear plate (1x)
4.2 Not in scope of delivery
21
22
Fig.5
21
Electrical pressure regulator (1x)
PREL-90
22
Branching module (1x)
PMBL-90
5 Assembly
Some O-rings will be left over with some mounting variants.
5.1 Mounting the connecting plates PAML-CP
Size G1/4 … G1
2
1
4
5
3
Fig.6
1. Orient the front plate and the rear plate so that the stamp number of1 2
the sub-base corresponds to the stamp number on the housing (1 to 1 and
2 to 2).
2. Insert the O-rings in the slots provided.5
3. Position the front plate and the rear plate .1 2
4. Fasten the front plate and the rear plate to the service unit using four1 2
screws and four washers . Tightening torque: 12 Nm ± 10% 3 4
5. Comply with the maximum screw-in depth for the pipe connection.
ISO 228 Max. screw-in depth [mm]
G1/2 12
G1/3 14
G1/2 16
G1 18
Size G1 1/4
7
6
17
18
19
20
Fig.7
1. Orient the front plate and the rear plate so that the stamp number of6 7
the sub-base corresponds to the stamp number on the housing (1 to 1 and
2 to 2).
2. Insert the O-rings or in the slots provided.8 aI
3. Position the front plate and the rear plate .6 7
4. Fasten the front plate and the rear plate to the service unit using theaH bJ
screws . Tightening torque: 12 Nm ± 10% aG
5. Observe the maximum screw-in depth for the pipe connection in accordance
with ISO 228: 20 mm
5.2 Mounting the mounting brackets PAML-MB
Always mount an individual device with two mounting brackets. Mount a service
unit with a mounting bracket at both the beginning and the end of the service unit
string and between the individual service units.
The grid width for he filter PFML-90 is 135 mm.
Fasten all required wall brackets with two M8 screws each at the specified9 bD
locations. The standard grid width between the wall brackets is 90 mm, and9
the distance in height between holes is 145 mm. All retaining screws mustaF
point upwards.
9
10
11
12
13
14
15
16
24
7
6 8
Fig.8
1. Orient the front plate 6 7 and the rear plate so that the stamp number of
the sub-base corresponds to the stamp number on the housing (1 to 1 and
2 to 2).
2. Insert the O-rings in the slots provided.8
3. Position the front plate and the rear plate .6 7
4. Push the screws into the front plate .aB aA
5. Place the seals between the service units.aJ
6. Place the front plate and rear plate in the slots of the service units.aA aC
7. Screw the screws into the rear plates . Tightening torque: 10 Nm ± 10% aB aC
8. Unscrew the retaining screws .aF
9. Position the service unit combination with the lugs in the slots of the wallaE
brackets .9
10. Tighten the retaining screws . Tightening torque: 2 Nm ± 10% aF
5.3 Assembly of the module connector PAML-MK
23 17
18
19
20
Fig.9
1. Note the flow direction from 1 to 2. The numbers on the product housing bC
serve as orientation.
2. Insert the retaining screws through the holes in the front plate .aG aH
3. Place the seal between the service units.aI
4. Place the front plate and rear plate in the slots of the service units.aH bJ
5. Tighten the screws . Tightening torque: 10 Nm ± 10% aG
6 Disassembly
1. Depressurise the system.
2. Check the surface temperature of the device. If necessary, let the device cool
down.
3. Remove the existing service unit string.
7 Technical data
PAML -CP -MB -MK
Operating pressure [MPa] 0 … 5
[bar] 0 … 50
[psi] 0 … 725
Temperature of medium [°C] +5 … +60
Ambient temperature [°C] +5 … +60
Tab. 1: Technical data

Tuotetiedot

Merkki: Festo
Kategoria: Ei luokiteltu
Malli: PAML-CP-90-HP3-G12

Tarvitsetko apua?

Jos tarvitset apua merkille Festo PAML-CP-90-HP3-G12 esitä kysymys alla ja muut käyttäjät vastaavat sinulle




Ei luokiteltu Festo Käyttöohjeet

Ei luokiteltu Käyttöohjeet

Viimeisimmät Ei luokiteltu Käyttöohjeet