IFM SF1004 Käyttöohje

Lue alta 📖 käyttöohje suomeksi merkille IFM SF1004 (6 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 6 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/6
Montageanleitung
Installation Instructions
Notice de Montage
Strömungssensor SF
Flow sensor SF
Sonde de débit SF
R
701150/04 05/2009
Bestimmungsgemäße Verwendung
Der Strömungssensor überwacht in Verbindung mit dem Schaltverstär-
ker VS0200 Strömungen in flüssigen und gasförmigen Medien. Die
Sensor-Verstärker-Kombination erfaßt, ob ein voreingestellter Strö-
mungswert erreicht ist (= Medium strömt) oder nicht (= Medium
strömt nicht) und meldet dies durch ein Schaltsignal.
Montage
Die Sensorspitze sollte vollständig ins Medium hineinragen.
Montieren Sie das Gerät bei waagerecht verlaufenden Rohren mög-
lichst seitlich (Abb 1). Bei Montage von unten sollte die Rohrleitung frei
von Ablagerungen sein. Bei Montage von oben sollte die Rohrleitung
vollständig mit dem zu überwachenden Medium gefüllt sein.
Montieren Sie das Gerät bei senkrecht verlaufenden Rohren in der
Steigleitung (Medium strömt aufwärts, Abb. 2).
A = 15mm für M12 x 1 und G 1/4; A = 33mm für G 1/2.
Um Fehlfunktionen zu vermei-
den, müssen Mindestabsnde
zwischen Sensor und Krümmun-
gen, Ventilen u. ä. eingehalten
werden: Mindestens 5 mal Rohr-
durchmesser an der Anströmseite
(A), mindestens 3 mal Rohrdurch-
messer an der Abströmseite (B).
Elektrischer Anschluss
Anschluss an Schaltverstärker VS0200; Spannungsversorgung nach
EN50178, SELV, PELV. Das Gerät darf nur von einer Elektrofachkraft
installiert werden. Befolgen Sie die nationalen und internationalen Vor-
schriften zur Errichtung elektrotechnischer Anlagen.
2
A
1
A
2
D
A
B
min.
5 x D
min.
3 x D
3
Dichtung Dichtung
Functions and features
In conjunction with the VS 0200 control monitor the flow sensor monitors
flows in liquids and gases. The sensor / control monitor combination
senses whether there is a preset flow rate (= medium flowing) or not
(= medium not flowing) and provides a switched signal.
Installation
The sensor tip must be completely immersed in the medium.
In the case of horizontal pipes mount the unit from the side, if possi-
ble (fig. 1). When the unit is to be mounted at the bottom of the pipe,
it should be free from deposits. When the unit is to be mounted at the
top of the pipe, it should be completely filled with the medium to be
monitored.
In the case of vertical pipes mount the unit in a place where the medi-
um flows upwards (fig. 2).
A = 15mm for M12 x 1 and 1/4"; A = 33mm for 1/2".
To avoid malfunction a minimum
distance between the flow moni-
tor and bends, valves or such like
must be observed. Min. 5 x pipe
diameter upstream (A), min. 3 x
pipe diameter downstream (B).
Electrical connection
Connection to control monitor VS 0200; voltage supply to EN50178,
SELV, PELV. The unit must only be mounted by an electrician.
The national and international regulations for the installation of
electrical equipment must be observed.
3
A
1
A
2
D
A
B
min.
5 x D
min.
3 x D
3
packing washer packing washer

Tuotetiedot

Merkki: IFM
Kategoria: Ei luokiteltu
Malli: SF1004

Tarvitsetko apua?

Jos tarvitset apua merkille IFM SF1004 esitä kysymys alla ja muut käyttäjät vastaavat sinulle




Ei luokiteltu IFM Käyttöohjeet

IFM

IFM E40581 Käyttöohje

8 Huhtikuuta 2025
IFM

IFM O3R252 Käyttöohje

8 Huhtikuuta 2025
IFM

IFM PG1704 Käyttöohje

8 Huhtikuuta 2025
IFM

IFM ME5016 Käyttöohje

11 Maaliskuuta 2025
IFM

IFM E30542 Käyttöohje

11 Maaliskuuta 2025
IFM

IFM PV2102 Käyttöohje

10 Maaliskuuta 2025
IFM

IFM AL2507 Käyttöohje

11 Helmikuuta 2025
IFM

IFM MK5361 Käyttöohje

10 Helmikuuta 2025
IFM

IFM AL2607 Käyttöohje

10 Helmikuuta 2025
IFM

IFM AL1325 Käyttöohje

7 Helmikuuta 2025

Ei luokiteltu Käyttöohjeet

Viimeisimmät Ei luokiteltu Käyttöohjeet