Lowell ACS-2010-RPC-HW Käyttöohje

Lowell Ei luokiteltu ACS-2010-RPC-HW

Lue alta 📖 käyttöohje suomeksi merkille Lowell ACS-2010-RPC-HW (3 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 3 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Lataa PDF

Sivu 1/3

INTERNAL USE ONLY: PN 24218

Lowell strives to provide accurate information while reserving the right to change specications and/or improve manufacturing methods without prior notication.

Spec 1109

Model ACS-2010-RPC-HW | Rev. 12.20.23 | pg. 1/3

POWER RATING: 120VAC 60Hz 20A

CHASSIS: 30” x 2” x 2” steel chassis with black powder epoxy finish

TERMINATION: Hardwired non-metallic flexible conduit (whip) with pigtail leads. The six ft.

conduit can be trimmed in the field if needed.

RECEPTACLES: Total of ten NEMA 5-20R receptacles (five duplex). One duplex is un-

switched (always on when the unit is supplied with power). Four duplexes are switched

(controlled by a remote switch or sequencer through the RPC terminal).

UNIVERSAL MOUNTING BRACKETS: The universal brackets allow for power strip instal-

lation in a variety of applications with receptacles facing front, center or rear. Brackets are

engineered with multiple mounting points and include two types of hardware to facilitate

easy installation in a rack with adjustable or fixed rails, to a wall, or under a desk/counter.

The brackets can be mounted so they are exposed for easy access or concealed beneath

the power strip for an aesthetically cleaner installation.

CERTIFICATION: ETL Listed in U.S./Canada

ORIGIN: Assembled in the U.S.A. with global components.

INSTALLATION

Use the universal mounting brackets to install the power strip near the equipment. Use

low-voltage cable to connect the RPC terminal to a remote switch or sequencer.

Hardwired power strip with ten 20A receptacles (ve duplex) and remote power control func-

tion (RPC) can be combined with a variety of remote switches or sequencers to provide a

low-voltage method of turning specic equipment on and off from a remote location. The

ability to safely control AC power distribution without directly accessing equipment adds

convenience, while minimizing the potential for unauthorized system modications.

ACS Series Model No.

ACS-2010-RPC-HW

AC Power Strip w/Remote Power Control

FEATURES

Certied

US Steel

Assembled

In USA

with Global

Components

A&E SPECIFICATIONS

The ETL Listed power strip with remote power control shall be Lowell model ACS-2010-

RPC-HW, which shall have a power rating of 120VAC 60Hz 20A. The chassis shall be steel

with black powder epoxy finish, measuring 30” x 2” x 2”. It shall feature one unswitched

and four switched NEMA 5-20R duplex receptacles. The four switched duplexes shall be

controlled by an external power switch or sequencer (ordered separately) that is connected

to the power strip’s remote power control terminal. The power strip shall be made in the

U.S.A. with global components. It shall terminate with a six ft. non-metallic flexible conduit

with pigtail leads, and include universal mounting brackets with hardware to mount to a

rack, wall or desk.

Note: An external

power switch or se-

quencer is required

(order separately,

pg. 2).

Six-ft.

non-metallic

exible conduit ro-

tates in any direction.

RPC terminal

connects to a

remote switch

or sequencer.

Four

duplexes are

controlled by a

remote switch

or sequencer

connected to

the RPC

terminal.

One duplex

is unswitched

(always on).

Mounting brackets

INTERNAL USE ONLY: PN 24218

Lowell strives to provide accurate information while reserving the right to change specications and/or improve manufacturing methods without prior notication.

Spec 1109

Model ACS-2010-RPC-HW | Rev. 12.20.23 | pg. 2/3

On: Green LED indicates AC power is applied to receptacles.

Power: Red LED indicates AC power is available.

Test: Test applies power to receptacles independent of remote switch or sequencer.

SW, Com: Connection between Switch and Common terminals activates internal relay and applies power to receptacles.

V+ Out: +24VDC output. Use only with RPS Series switches

Ex. Lowell RPS Series

REMOTE POWER CONTROL: Use low-voltage cable to connect the RPC terminal to an external switch or sequencer.

Remote

Switch

Sequencer

Connection to Remote Switch

(wall or rackmount):

Connection to Sequencer or Control System

with dry contact closure:

RPC Terminal:

Ex. Lowell SEQ Series

(w/classic connections)

Model No.

Description

RPSW-P

SPST switch w/maintained closure, one-gang white wall plate, rocker switch

RPSW-KP

SPST switch w/maintained closure, one-gang white wall plate, key switch

RPSB-R

SPST switch w/maintained closure, 1U rackmount panel, rocker switch

PRSB-KR

SPST switch w/maintained closure, 1U rackmount panel, key switch

SEQ-4

Four-step sequencer

SEQ-8

Eight-step sequencer

SEQR-4

Four-step rackmount sequencer w/rocker switch, 1U

SEQR-4K

Four-step rackmount sequencer w/key switch, 1U

SEQR-8

Eight-step rackmount sequencer w/rocker switch, 1U

SEQR-8K

Eight-step rackmount sequencer w/key switch, 1U

COMPATIBLE Switches & Sequencers: Order separately. See individual product spec sheets for more information.

3) REATTACH CONNECTOR:

Twist/push the connector to attach it to

the shortened conduit.

1) REMOVE EXCESS LENGTH:

Snip reinforcing rib at desired length.

Bend the conduit to expose the cut and

carefully cut around the conduit without

cutting the wires inside. Remove excess

length.

2) REMOVE CONNECTOR:

Carefully snip the last rib(s) to loosen the

connector from the excess length, then

twist/pull to remove it.

HOW TO TRIM THE CONDUIT: The 6 ft. non-metallic flexible conduit can be trimmed in the field.

INTERNAL USE ONLY: PN 24218

Lowell strives to provide accurate information while reserving the right to change specications and/or improve manufacturing methods without prior notication.

Spec 1109

Model ACS-2010-RPC-HW | Rev. 12.20.23 | pg. 3/3

UNIVERSAL MOUNTING BRACKETS: The brackets can be mounted exposed for easy access or concealed for a cleaner install. Includes

variety of hardware for versatile installation. (2) 1/4"-20 x 1/2" screws

(2) at nuts

(2) 10-32 x 1/2" screws

(2) cage nuts

(2) Brackets

RACK w/ ADJUSTABLE RAILS

(side mount : Mount to horizontal side )

supports with universal brackets, 1/4"-20

screws, flat nuts.

RACK w/ ADJUSTABLE RAILS

(rear mount): Mount to rear rail with univer-

sal brackets, 10-32 screws.

RACK w/ FIXED POSITION RAILS

(and rear Z-angle bracket): Mount to Z-an-

gle with universal brackets, 10-32 screws,

cage nuts.

T H I S

SPEC

SERIES SUMMARY

Power NEMA Chassis Chassis On/Off Surge Remote Mounting Country

Model No. Rating Receptacles Circuits Length Pro le Termination Switch Suppression Power Control Aids of Origin

ACS-1505-SW 15A 5 (15A) 1 12" Standard 6' Det. cord Yes --- --- Brackets U.S.

ACS-1505-SW-SD 15A 5 (15A) 1 12" Standard 6' Det. cord Yes 2-stage --- Brackets U.S.

ACS-1506 15A 6 (15A) 1 20" Low 6' Fixed cord --- 1-stage --- Clips China

ACS-1506-WW 15A 6 (15A) 1 12" Low 6' Fixed cord --- --- --- Screws U.S.

ACS-1507 15A 7 (15A) 1 12" Low 6' Det. cord --- --- --- Screws U.S.

ACS-1512 15A 12 (15A) 1 32" Low 12' Fixed cord --- 1-stage --- Clips China

ACS-1524 15A 24 (15A) 1 60" Low 12' Fixed cord --- 1-stage --- Clips China

ACS-1524-2C 15A 24 (15A) 2 70" Low Pigtail leads --- --- --- Clips China

ACS-2012 20A 8 (15A) + 4 (20A) 1 32" Low 12' Fixed cord --- 1-stage --- Clips China

ACS-2024 20A 16 (15A) + 8 (20A) 1 70" Low 12' Fixed cord --- 1-stage --- Clips China

ACS-2014-HW 20A 14 (20A) 1 30" Standard 6' Conduit --- --- --- Brackets U.S.

ACS-2014-2C-HW 20A 8 (15A) + 6 (20A) 2 30" Standard 6' Conduit --- --- --- Brackets U.S.

ACS-2020-6C-HW 20A 20 (20A) 6 60" Standard 6' Conduit --- --- --- Brackets U.S.

ACS-2020-IG-6C-HW 20A 20 (I.G. 20A) 6 60" Standard 6' Conduit --- --- --- Brackets U.S.

ACS-2020-IG-10C-HW 20A 20 (I.G. 20A) 10 60" Standard 6' Conduit --- --- --- Brackets U.S.

ACS-2024-2C 20A 24 (20A) 2 70" Low Pigtail leads --- --- --- Clips China

ACS-1510-RPC 15A 10 (15A) 1 30" Standard 6' Det. cord --- --- Yes Brackets U.S.

ACS-2010-RPC-HW 20A 10 (20A) 1 30" Standard 6' Conduit --- --- Yes Brackets U.S.

ACS-2018-5C-RPC-HW 20A 18 (20A) 5 60" Standard 6' Conduit --- --- Yes Brackets U.S.

ACS-2018-5C-RPCP-HW 20A 18 (20A) 5 60" Standard 6' Conduit --- 1-stage Yes (P) Brackets U.S.

Chassis Pro le = Standard pro le (2" x 2"), Low pro le (1.625" x 1.375")

Termination = Det. cord (detachable cord), Fixed cord (cord is attached–cannot be removed), Conduit (non-metallic  exible whip w/pigtail leads), Pigtail leads (leads at ends of chassis—no whip)

Switch = Yes (On/off rocker switch)

Surge Suppression = 1-stage (basic surge protection), 2-stage (surge protection with backup)

Remote Power Control = Some receptacles are controlled by a remote switch or sequencer (ordered separately); (P) indicates compatibility with Lowell P-Series pass-through sequencers.

Mounting Aids = Brackets (multi-hole brackets with hardware), Clips (clips and screws with wire tires), or Screws (power strips can mount to rear of US or USV Series shelves).