Maruyama MBS329 Käyttöohje
Maruyama
Grastrimmer
MBS329
Lue alta 📖 käyttöohje suomeksi merkille Maruyama MBS329 (16 sivua) kategoriassa Grastrimmer. Tämä opas oli hyödyllinen 2 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/16
Brushcutter
Cortadora
MBS329
English: Page US-1～7
Espanol: Página ES-1～7
― US-1 ―
1.Read and understand this Instruction Manual before
using the this product. Be thoroughly familiar with the
proper use of the Brushcutter.
2.Never allow children to operate the Brushcutter. it is not a
toy. Never allow adults to operate the unit without first
reading the Instruction Manual.
3.Become familiar with the controls and know how to
stop the engine quickly.
4.ALWAYS WEAR SAFETY GLASSES or other
suitable eye protection, and hearing protection.
5.Keep the area of operation clear of all persons,
particularly small children and pets.
6.Never operate the Brushcutter when you are fatigued.
Never operate without proper guards or other
protective safety devices in place.
7.Dress properly; do not wear loose clothing or jewelry.
They can be caught in moving parts. Always wear
substantial footwear, long pants, and long sleeved
shirt.
8.Gasoline is highly flammable; handle it carefully. Fill
the fuel tank with the correct mixture of gasoline and
oil before trying to start the engine.
A. Use an approved fuel container for storing the
gasoline/oil mixture.
B. Do not fill the tank when the engine is hot or running.
C. Do not smoke while handling gasoline.
D. Fill the fuel tank outdoors and up to about 10mm
from the top of the tank, not the top of the filler neck.
E. Wipe any spilled gasoline before starting the
engine.
9.Always be sure of your footing; keep a firm hold of
the handles with both hands, and walk, never run.
10.Use the right tool for the job. Do not use the
Brushcutter for any job that is not recommended
by the manufacturer.
11.Keep all fasteners tight to be sure the Brushcutter
is in safe working condition. Follow the mainte-
nance instructions provided on page US-6 to US-7
of this manual.
12.Do not put hands or feet near or under the
rotating/ moving parts. Keep clear at all times.
13.If the Brushcutter should start to vibrate
abnormally, stop the engine and check
immediately for the cause. Vibration is generally
a warning of trouble.
14.Do not trim too close to the ground in order to
avoid hitting small stones or other debris. Avoid
using the Brushcutter near rocks, gravel, stones
and similar matter.
15.Use the Brushcutter only in daylight or good
artificial light.
16.Shut off the engine and be certain the attached
tool has completely stopped rotating/moving
before inverting the machine.
Model MBS329
Overall length (mm) 2710
Overall width (mm) 345
Dimensions
Overall height (mm) 465
Dry weight (kg / lbs) 9,6/ 21,2
Gear Spiral bevel gear
Deduction ratio 1:1,46
Model AE320
Type Air cooled. 2-cycle, 1-cylinder
Engine Displacement (cc) 31,8
Fuel Tank Capacity (liter / qts.) 1,0
Carburetor Diaphragm Type
Ignition Soild State
Spark plug NGK BPM6Y
Spark plug gap (mm / in.) 0,6 – 0,7 / 0,024 – 0,028
Engine
Fuel Mixture
USE ONLY NON
-
LEADED REGULAR GASOLINE.
2
-
CYCLE OIL MIX 25:1 RATIO MUST BE APPROVED
FOR AIR
-
COOLED ENGINES.
SPECIFICATIONS
SAFETY INSTRUCTIONS
― US-2 ―
PRODUCT DISCRIPTION
ASSEMBLY INSTRUCTIONS
(1) Flexible shaft
1) Flexible shaft and straight shaft
Remove bolt with hex. wrench, insert outer fitting
(with O-ring ) into joint pipe and fasten bolt.
2) Flexible shaft and engine
Insert outer fitting into clutch case with pulling up pin.
Be sure pin returns to original position by spring and
outer fitting never comes off from clutch case.
(2) Throttle lever, throttle wire, lead wire
1) Throttle lever side
- take a drive shaft tube through a loop of lead wire.
The lead wire is connected to upper side of throttle
lever.
- take two terminals of lead wire through the hole of
grip. Take a wire end that shaped drum through the
hole of grip.
- connect the wire end to the hole of lower side of
throttle lever. Hold the drive shaft tube between upper
and lower side of throttle lever.
- tighten two screws and two square nuts.
2) Engine side
- Let throttle wire and lead wire through plastic tube.
- Insert the throttle wire through the wire adjuster
sleeve on the carburetor bracket. Make sure the end
of the throttle wire housing is seated positively in the
sleeve.
- Position the slotted fitting on the carburetor so the
recessed hole for the lug is away from the wire
adjuster sleeve.
- Rotate the carburetor throttle cam and slip the throttle
wire through the slot in the slotted fitting, making sure
the wire lug drops into the recessed hole.
- Operate the throttle trigger a few times to make sure
that it works correctly.
- Connect the lead wire to the engine-side terminal.
Pin
Inner shaft
Oute
r
fitting
Clutch axis
Clutch case
O-ring
Joint pipe
Bolt
Oute
r
1. Gearcase
2. Drive Shaft Assembly
3. Model Name
4. Loop Handle
5. Throttle Trigger and Stop Switch
6. Shaft Grip
7. Flexible Shaft
8. Throttle Cable and Stop Switch Wires
9. Clutch Drum Housing
10. Engine
11. Frame
12. Pad
13. Air Filter
14. Fuel Tank
15. Brushcutter Blade
1
2
3
4
5
6
7
9
8
10
11 12
13
14
15
Lead wires Lock nut
Carbureto
r
bracket
Throttle wire housing
Throttle wire
Slotted fitting
Wire lug
Recessed hole
Wire adjuster sleeve
Screw
Grip
Upper side of
throttle lever
Lower side of
throttle lever
Driveshaft tube
Throttle wire end
Square nut
Lead wire
Tuotetiedot
| Merkki: | Maruyama |
| Kategoria: | Grastrimmer |
| Malli: | MBS329 |
Tarvitsetko apua?
Jos tarvitset apua merkille Maruyama MBS329 esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Grastrimmer Maruyama Käyttöohjeet
26 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
Grastrimmer Käyttöohjeet
Viimeisimmät Grastrimmer Käyttöohjeet
22 Lokakuuta 2024
20 Lokakuuta 2024
20 Lokakuuta 2024
20 Lokakuuta 2024
19 Lokakuuta 2024
19 Lokakuuta 2024
19 Lokakuuta 2024
19 Lokakuuta 2024
19 Lokakuuta 2024
19 Lokakuuta 2024