Metra 95-7822 Käyttöohje

Lue alta 📖 käyttöohje suomeksi merkille Metra 95-7822 (8 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 5 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/8
Metra. The World’s Best Kits.® MetraOnline.com © COPYRIGHT 2024 METRA ELECTRONICS CORPORATION REV. 4/10/24 INST95-7822
Attention! With the key out of the ignition,
disconnect the negative battery terminal
before installing this product. Ensure that all
installation connections are secure before
cycling the ignition to test this product.
I N S TA L L AT I O N I N S T R U C T I O N S
95-7822
KIT FEATURES
DDIN radio provision
KIT COMPONENTS
• A) Radio trim panel • B) Radio bracket • C) #14 x 1/2” Phillips screw (1)
TOOLS REQUIRED
• Panel removal toolPhillips screwdriver
TABLE OF CONTENTS
Dash Disassembly 2 ..................................................
Kit Assembly .......................................................... 3
WIRING & ANTENNA CONNECTIONS
(sold separately)
Visit metraonline.com for audio/video and
steering wheel control interface options.
Wire harness: 70-1729
Antenna adapter: 40HD-11
A B C
Honda CR-Z (with factory navigation) 2011-2016
Visit for more detailed information about the product and up-to-date vehicle MetraOnline.com
specific applications
386.257.1187
|
MetraOnline.com
2
DASH DISASSEMBLY
1. Unclip and remove the lower dash panel
cover above the pocket and remove the
8mm/Phillips screw. (Figures A and B)
2. Unclip and remove the radio from the
dash. (Figure C)
Tip: Start at the top of the radio.
(Figure B) (Figure D)
(Figure C) (Figure A)
3. Unplug and remove the radio.
4. Disassemble the factory NAV unit by
removing the (4) Phillips screws holding
it to the factory dash panel. (Figure D)
Continue to Kit Assembly
REV. 4/10/2024 INST95-7822 3
KIT ASSEMBLY
(Figure B)
1. radio bracketSecure the to the factory
dash panel using the factory hardware.
(Figure A)
2. radio trim panelSnap the into the
factory dash panel. (Figure B)
3. Slide the DDIN radio into the radio
bracket assembly and secure using
hardware supplied with the radio.
(Figure C)
(Figure A) (Figure C)
4. Locate the factory wiring harness in
the dash. Metra recommends using
the proper mating adapter from Metra
or AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
5. Reassemble dash in reverse order of
disassembly. A #14 x 1/2” screw has
been provided if the factory 8mm
mounting screw has been lost or
discarded.

Tuotetiedot

Merkki: Metra
Kategoria: Ei luokiteltu
Malli: 95-7822

Tarvitsetko apua?

Jos tarvitset apua merkille Metra 95-7822 esitä kysymys alla ja muut käyttäjät vastaavat sinulle




Ei luokiteltu Metra Käyttöohjeet

Metra

Metra AXDSPX-ETH1 Käyttöohje

3 Huhtikuuta 2025
Metra

Metra 70-5526 Käyttöohje

12 Maaliskuuta 2025
Metra

Metra 99-8725B Käyttöohje

15 Tammikuuta 2025
Metra

Metra 99-7382HG Käyttöohje

15 Tammikuuta 2025
Metra

Metra 99-7397B Käyttöohje

15 Tammikuuta 2025
Metra

Metra 99-7421 Käyttöohje

15 Tammikuuta 2025

Ei luokiteltu Käyttöohjeet

Viimeisimmät Ei luokiteltu Käyttöohjeet