PAC AP4-CH42 Käyttöohje
PAC
Ei luokiteltu
AP4-CH42
Lue alta 📖 käyttöohje suomeksi merkille PAC AP4-CH42 (6 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 4 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/6
© 2024 Stinger. All rights reserved. PAC is a Power Brand of Stinger.
PAC-audio.com Page 1
Rev 1
2/5/2024
Advanced Amplier Interface for
Chrysler / Dodge / Jeep / RAM
AP4-CH42
The AP4-CH42 provides a 6-channel pre-amp output for use with aftermarket audio equipment. Using the full range, xed
level head unit output, in conjunction with CAN messages, the AP4-CH42 delivers a variable 5v RMS pre-amp output with
fading, balance, equalization, and level control capabilities. The module also retains all audio from other vehicle features
such as factory navigation prompts, Bluetooth, uConnect, and parking sensor chimes. A data controlled remote amplier
turn on wire is also provided by the AP4-CH42. When used in conjunction with the APA-TOS1 (sold separately), the module
can provide a variable 2-channel ber optic digital audio output (TOSLINK).
Introduction and Features
Important Notes
1. Compatible with both amplied and non-amplied factory systems.
• Amplied Vehicles
• Compatible with all data-bus controlled amplied systems, no matter the screen size (including the 12" screen). To
identify these systems, look for logos on door speakers, tweeters, dash speakers or the subwoofer to conrm if the
vehicle has an amplied system (Alpine & Harmon Kardon). Some vehicles may not always have branded systems.
Unbranded amplied systems are generally identied by locating a center channel speaker or subwoofer
• Non-Amplied Vehicles
• Jeep Wrangler: Compatible with all screen sizes (5", 7" and 8.4").
• All other models: Only compatible in vehicles equipped with the 7" or 8.4" screen. Vehicles equipped with the 5"
screen are not compatible.
• If you are installing the AmpPRO in a vehicle that is not equipped with a factory amplier, you must add an amplier
to the vehicle's speakers, as the factory radio will no longer have a 4 channel variable output after it has been re-
congured by the AmpPRO. For example, you can not add only a subwoofer to a non-amplied vehicle, as the radio
will no longer power the cabin speakers properly.
• Non-amplied vehicles equipped with an Active Noise Cancellation (ANC) system require the ANC module to be
bypassed. This can be done manually or with the ANC bypass harness ANC-CH01. See page 2 Step 6d to re-congure
the factory radio.
2. If a factory amplier is present, it must remain connected and in the vehicle after the AmpPRO has been installed.
3. The remote output is rated at 2A of current. If more current is needed an external relay must be used.
4. Channels 5 and 6 are non-fading outputs. The output level of channels 5 and 6 can be controlled using the supplied level
control knob.
5. The chime volume and minimum volume levels are set to 0 dB by default. If you are happy with this level in your particular
application, additional adjustment is not required. Please refer to the Setup and Conguration section on page 2 for more details.
6. The level control knob must be connected in order to manually adjust the chime volume and minimum volume settings.
7. The factory radio's speed controlled volume and surround sound mode are not supported by the AP4 outputs.
8. When using the TOSLINK output (APA-TOS1 sold separately), DIP switch 1 must be on in order for all warning chimes to be
heard through the sound system (see page 2 Step 6a for details).
9. No adjustments can be made manually using the programming button, or the factory SWC when the module is connected to
a PC.
Module Layout
Interface Connector 1
Expansion Port
Programming Button
Feature Select
DIP switches
Non-Fading Level Control
Knob Connection
USB Connection
LED 1
TOSLINK Output
(APA-TOS1 sold separately)
Front Output
Ch. 1(L) and 2(R)
Rear Output
Ch. 3(L) and 4(R)
Non-Fading Output
Ch. 5(L) and 6(R)
LED 2
© 2024 Stinger. All rights reserved. PAC is a Power Brand of Stinger.
PAC-audio.com Page 2
Rev 1
2/5/2024
Advanced Amplier Interface for
Chrysler / Dodge / Jeep / RAM
AP4-CH42
Installation
1. Remove factory radio.
2. Disconnect the main 32 & 12-Pin factory harness from radio.
3. Connect AmpPRO harness to vehicle harness.
4. Connect AmpPRO harness to factory radio.
5. If you are using the AmpPRO in a vehicle with a factory amplier, leave the "Factory Speaker Connection Point" connectors
plugged into each other. If the vehicle has no factory amplier, connect the aftermarket amplier's speaker outputs to the
provided "Factory Speaker Connection Harness" and connect to the "Factory Speaker Connection Point."
6. Set any feature DIP switches that apply to your install.
a. Set DIP switch 1 on (down) to activate two channel mode. In this mode, both the TOSLINK and front RCA outputs (1
and 2) become non-fading outputs. All rear chimes will also be routed through these outputs in two channel mode
b. Set DIP switch 2 on (down) to lower the RCA output voltage to 4v. Leave DIP switch 2 o (up) to keep the RCA output
voltage at 5v. See troubleshooting section on page 6 for more details.
c. DIP switch 3 is not used.
d. DIP switch 4 is for vehicles without a factory amplier. Set DIP switch 4 on (down) to recongure the radio for proper
communication with the AmpPRO.
7. If you are using the APA-TOS1 (sold separately) refer to the instructions included with that product for its installation
8. Connect the AmpPRO harness to the module.
9. Connect the level control knob to the module and install in an accessible location.
10. Connect the signal cables and remote input from the aftermarket amplier.
11. Complete the "Radio Reset Procedure." (see page 5 for more information)
a. Make sure the radio is fully booted and LED 1 is on. Press and hold the "Programming Button" until the LEDs alternate
ashing amber, then release.
b. The LEDs will alternate ashing green and the radio will re-boot
12. Turn the vehicle o, close the doors and let the vehicle sit for 5 minutes.
Two Channel Mode 5v / 4v Preout Non-Amplied VehiclesNo Function
1 32 4
Set DIP switches to the ON position to activate the corresponding features.
Set DIP switches to the OFF position for any features that are not desired.
Wiring Connection Chart
© 2024 Stinger. All rights reserved. PAC is a Power Brand of Stinger.
PAC-audio.com Page 3
Rev 1
2/5/2024
Advanced Amplier Interface for
Chrysler / Dodge / Jeep / RAM
AP4-CH42
PLEASE NOTE: Knob must be connected to module for Minimum Volume or Chime adjustments.
Manually Setting the Chime Volume
You can manually set the level of the factory chime using either the programming button on the side of the interface or the
factory SWC. If you would like to set the chime volume using the AmpPRO PC app please proceed to the AmpPRO PC app
section.
Setting the chime volume using the programming button
1. Start with the level control knob turned all the way down (counter-clockwise).
2. Press the programming button on the side of the interface.
3. LED 1 will turn green and the chimes will begin continuously sounding.
4. Turn the level control knob clockwise until the desired chime level is reached.
5. You can now either press the programming button twice or wait ten seconds to exit the settings.
Setting the chime volume using the factory SWC
1. Start with the level control knob turned all the way down.
2. Press and hold the track down button on the factory SWC (Back left of steering wheel) for approximately ten seconds.
PLEASE NOTE: The radio will respond to the SWC commands during this process, this is normal and has no eect on
the AP4 operation.
3. LED 1 will turn green and the chimes will begin continuously sounding.
4. Turn the level control knob clockwise until the desired chime level is reached.
5. You can now either press the programming button twice or wait ten seconds to exit the settings.
Manually Setting the Minimum Volume
If the minimum volume of the radio (factory radio volume level 1) is too loud, you can manually set the level of the minimum
volume using either the programming button on the side of the interface or the factory SWC. If you would like to set the
minimum volume using the AmpPRO PC app, please proceed to the AmpPRO PC app section.
Setting the minimum volume using the programming button
1. Start with the level control knob turned all the way down (counter-clockwise).
2. Set the amp gains to the desired level.
3. Set the volume on the factory radio to 1.
4. Press the programming button on the side of the interface twice.
5. LED 1 will turn amber and the chimes will begin sounding every ve seconds.
6. Turn the level control knob clockwise until the desired minimum volume level is reached.
7. You can now either press the programming button once or wait ten seconds to exit the settings.
Setting the minimum volume using the factory SWC
1. Start with the level control knob turned all the way down (counter-clockwise).
2. Set the amp gains to the desired level.
3. Set the volume on the factory radio to 1.
4. Press and hold the track up button on the factory SWC (Back left of steering wheel) for approximately ten seconds.
PLEASE NOTE: The radio will respond to the SWC commands during this process, this is normal and has no eect on
the AP4 operation.
5. LED 1 will turn amber and the chimes will begin sounding every ve seconds.
6. Turn the level control knob clockwise until the desired minimum volume level is reached.
7. You can now either press the programming button once or wait ten seconds to exit the settings.
Setup and Conguration
1. Turn the ignition on. LED 1 on the interface will turn on and the +12v remote output will turn on.
2. Set the amp gain(s) to the desired level. We recommend using an oscilliscope and test tones to set the amp gain(s). Please
refer to the MECP Advanced study guide (p. 360) if you are unfamiliar with this process.
3. Check volume, balance, fade and EQ settings.
4. If you would like to adjust the chime volume or minimum volume, do so using one of the methods outlined below. If you are
happy with the default levels, no adjustments are necessary.
Tuotetiedot
Merkki: | PAC |
Kategoria: | Ei luokiteltu |
Malli: | AP4-CH42 |
Tarvitsetko apua?
Jos tarvitset apua merkille PAC AP4-CH42 esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Ei luokiteltu PAC Käyttöohjeet
15 Lokakuuta 2024
15 Lokakuuta 2024
15 Lokakuuta 2024
15 Lokakuuta 2024
15 Lokakuuta 2024
15 Lokakuuta 2024
15 Lokakuuta 2024
15 Lokakuuta 2024
15 Lokakuuta 2024
15 Lokakuuta 2024
Ei luokiteltu Käyttöohjeet
- Ei luokiteltu Whirlpool
- Ei luokiteltu Jocel
- Ei luokiteltu BEKO
- Ei luokiteltu Apc
- Ei luokiteltu DeWalt
- Ei luokiteltu Siemens
- Ei luokiteltu Hama
- Ei luokiteltu Neewer
- Ei luokiteltu Gigabyte
- Ei luokiteltu Gree
- Ei luokiteltu Hazet
- Ei luokiteltu Philips
- Ei luokiteltu Topeak
- Ei luokiteltu IFM
- Ei luokiteltu Avantree
- Ei luokiteltu Schwaiger
- Ei luokiteltu IKEA
- Ei luokiteltu AeroCool
- Ei luokiteltu Samsung
- Ei luokiteltu Garmin
- Ei luokiteltu StarTech.com
- Ei luokiteltu Imarflex
- Ei luokiteltu Edgestar
- Ei luokiteltu Audient
- Ei luokiteltu McIntosh
- Ei luokiteltu Venom
- Ei luokiteltu Legrand
- Ei luokiteltu Cudy
- Ei luokiteltu Candy
- Ei luokiteltu Axis
- Ei luokiteltu Liebherr
- Ei luokiteltu Carson
- Ei luokiteltu Gourmetmaxx
- Ei luokiteltu Truelife
- Ei luokiteltu ETA
- Ei luokiteltu Lindy
- Ei luokiteltu HP
- Ei luokiteltu Pioneer
- Ei luokiteltu Summit
- Ei luokiteltu EarFun
- Ei luokiteltu Ecler
- Ei luokiteltu Digitus
- Ei luokiteltu Panasonic
- Ei luokiteltu Unicol
- Ei luokiteltu Audio-Technica
- Ei luokiteltu Toa
- Ei luokiteltu Vox
- Ei luokiteltu Pyle
- Ei luokiteltu Lenovo
- Ei luokiteltu Noctua
- Ei luokiteltu Schneider
- Ei luokiteltu Kindermann
- Ei luokiteltu Anker
- Ei luokiteltu Privileg
- Ei luokiteltu Fluval
- Ei luokiteltu Heatit
- Ei luokiteltu Ryobi
- Ei luokiteltu Kodak
- Ei luokiteltu Sharkoon
- Ei luokiteltu DataVideo
- Ei luokiteltu RGV
- Ei luokiteltu Guzzanti
- Ei luokiteltu Bluesound
- Ei luokiteltu Aplic
- Ei luokiteltu Speco Technologies
- Ei luokiteltu Tripp Lite
- Ei luokiteltu Infiniton
- Ei luokiteltu Smart-AVI
- Ei luokiteltu AXESS
- Ei luokiteltu DAB
- Ei luokiteltu Blaupunkt
- Ei luokiteltu NEP
- Ei luokiteltu Ansmann
- Ei luokiteltu Einhell
- Ei luokiteltu Planet
- Ei luokiteltu Fezz
- Ei luokiteltu JBL
- Ei luokiteltu DeepCool
- Ei luokiteltu Kali Audio
- Ei luokiteltu Chief
- Ei luokiteltu Majority
- Ei luokiteltu Helix
- Ei luokiteltu Elation
- Ei luokiteltu Magmatic
- Ei luokiteltu Zendure
- Ei luokiteltu Logilink
- Ei luokiteltu Majestic
- Ei luokiteltu Leviton
- Ei luokiteltu Soundstream
- Ei luokiteltu Xaoc
- Ei luokiteltu Hohner
- Ei luokiteltu Britax
- Ei luokiteltu Steiner
- Ei luokiteltu Vonroc
- Ei luokiteltu Bellari
- Ei luokiteltu Rolls
- Ei luokiteltu Ordo
- Ei luokiteltu Ground Zero
- Ei luokiteltu OnePlus
- Ei luokiteltu CRUX
- Ei luokiteltu Karma
- Ei luokiteltu Ridem
- Ei luokiteltu Glemm
- Ei luokiteltu StarIink
- Ei luokiteltu HomeCraft
- Ei luokiteltu Nostalgia
- Ei luokiteltu GameDay
- Ei luokiteltu X-Lite
- Ei luokiteltu Söll
- Ei luokiteltu Sparkle
- Ei luokiteltu Edouard Rousseau
- Ei luokiteltu Caberg
- Ei luokiteltu Exped
- Ei luokiteltu Igloo
- Ei luokiteltu Heusinkveld
- Ei luokiteltu KED
- Ei luokiteltu EPEVER
- Ei luokiteltu Grothe
- Ei luokiteltu Cane Creek
- Ei luokiteltu Swiss Eye
- Ei luokiteltu SilverStone
- Ei luokiteltu Dreame
- Ei luokiteltu Foreo
- Ei luokiteltu Tesla
- Ei luokiteltu Aquael
- Ei luokiteltu Klarstein
- Ei luokiteltu Lauten Audio
- Ei luokiteltu Toddy
- Ei luokiteltu Lexivon
- Ei luokiteltu Icy Dock
- Ei luokiteltu Elta
- Ei luokiteltu ASI
- Ei luokiteltu Gurari
- Ei luokiteltu Varia
- Ei luokiteltu SPL
- Ei luokiteltu I-Tec
- Ei luokiteltu Xigmatek
- Ei luokiteltu Storcube
- Ei luokiteltu Tracer
- Ei luokiteltu Shark
- Ei luokiteltu REMKO
- Ei luokiteltu Phanteks
- Ei luokiteltu EnOcean
- Ei luokiteltu EK Water Blocks
- Ei luokiteltu Hoymiles
- Ei luokiteltu Envertech
- Ei luokiteltu Cougar
- Ei luokiteltu Asrock
- Ei luokiteltu Audiotec Fischer
- Ei luokiteltu Furman
- Ei luokiteltu Cata
- Ei luokiteltu Radial Engineering
- Ei luokiteltu Hamilton Beach
- Ei luokiteltu Craftsman
- Ei luokiteltu Edesa
- Ei luokiteltu Lowell
- Ei luokiteltu IPGARD
- Ei luokiteltu Libec
- Ei luokiteltu Silver Cross
- Ei luokiteltu American DJ
- Ei luokiteltu Profoto
- Ei luokiteltu Black Lion Audio
- Ei luokiteltu Puls Dimension
- Ei luokiteltu Wasp
- Ei luokiteltu Gamewright
- Ei luokiteltu Claypaky
- Ei luokiteltu Premier Mounts
- Ei luokiteltu MuxLab
- Ei luokiteltu Impact
- Ei luokiteltu Heritage Audio
- Ei luokiteltu Safco
- Ei luokiteltu Monoprice
- Ei luokiteltu Stabila
- Ei luokiteltu CTA Digital
- Ei luokiteltu HammerSmith
- Ei luokiteltu Cyrus
- Ei luokiteltu ATen
- Ei luokiteltu Bialetti
- Ei luokiteltu Xlyne
- Ei luokiteltu Plant Craft
- Ei luokiteltu Sungrow
- Ei luokiteltu Grundfos
- Ei luokiteltu Bazooka
- Ei luokiteltu Carlsbro
- Ei luokiteltu MoFi
- Ei luokiteltu Blackburn
- Ei luokiteltu Bang And Olufsen
- Ei luokiteltu Cowon
- Ei luokiteltu Horizon Fitness
- Ei luokiteltu Jilong
- Ei luokiteltu Gamesir
- Ei luokiteltu Yaesu
- Ei luokiteltu Concept2
- Ei luokiteltu CTOUCH
- Ei luokiteltu RCF
- Ei luokiteltu Microchip
- Ei luokiteltu WilTec
- Ei luokiteltu Wimberley
- Ei luokiteltu Playtive
- Ei luokiteltu Vimar
- Ei luokiteltu Osprey
- Ei luokiteltu Hosa
- Ei luokiteltu Havis
- Ei luokiteltu Emerson
- Ei luokiteltu Biltema
- Ei luokiteltu Bogen
- Ei luokiteltu Electro Harmonix
- Ei luokiteltu Chrome-Q
- Ei luokiteltu Galaxy Audio
- Ei luokiteltu Altman
- Ei luokiteltu Aiphone
- Ei luokiteltu Atlas
- Ei luokiteltu Graco
- Ei luokiteltu MARTOR
- Ei luokiteltu Mean Well
- Ei luokiteltu Exelpet
- Ei luokiteltu Trendnet
- Ei luokiteltu G-Technology
- Ei luokiteltu CubuSynth
- Ei luokiteltu Infasecure
- Ei luokiteltu SecureSafe
- Ei luokiteltu Intellinet
- Ei luokiteltu Hikoki
- Ei luokiteltu Butler
- Ei luokiteltu ProfiCook
- Ei luokiteltu Arovec
Viimeisimmät Ei luokiteltu Käyttöohjeet
22 Lokakuuta 2024
22 Lokakuuta 2024
22 Lokakuuta 2024
22 Lokakuuta 2024
22 Lokakuuta 2024
22 Lokakuuta 2024
22 Lokakuuta 2024
22 Lokakuuta 2024
22 Lokakuuta 2024
22 Lokakuuta 2024