PAC OS-1 BOSE Käyttöohje

PAC Ei luokiteltu OS-1 BOSE

Lue alta 📖 käyttöohje suomeksi merkille PAC OS-1 BOSE (2 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 4 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/2
Pacifi c Accessory Corporation - 1502 S. Santa Fe Street, Santa Ana, CA 92705
techsupport@pac-audio.com • Voice: 714-835-3022 • Fax: 714-835-3233 • www.pac-audio.com
Page
6-25-04
OS-1 BOSE
General Motors OnStar
®
Bose® Interface
Installation Instructions.
interface and the OEM-1 premium sound system interface and cable . The OS-1 has on board switching, and amplifi cation to
new replacement radio. The OS-1 can also be used when a stereo and amplifi er combination system is installed. Separate
speakers can be added if desired.
an “ON” command from the OnStar® system.
Cadillac
1999 - 2000 Escalade*, 2002 Escalade.
Chevrolet
1998 - 2002 Suburban and Tahoe.
GMC
1998 - 2002 Suburban,
Yukon and Denali.
Pontiac*: Please note 1998-2003 Grand Prix w/Bose® - this interface is not designed for this vehi-
cle, however, you can order the AMP-GM21B (1998-1999 Grand Prix) or AMP-GM21C (2000-2003 Grand Prix) harness
to replace the AMP-GM21A harness to make this interface work correctly.
The OS-1 will interface with all GM radios that use the 21 pin / 9 pin connectors. If there is a “RDS logo on the radio face or
the radio uses the 24 pin / 12 pin connectors, this interface will not work.
* See bulletin on page 2
OEM-1
FACTORY SOU ND SYSTE M
INTERFACE
Pacific Accessory Corporation - Santa An a, CA 9270 5
Right Fron t
Left Fr ont
Left Rear
Right Rear
OS-1
General Motors OnStar ®Interface
Factory Radi o Replacemen t and
Retentio n o f OnStar ®
Option
Pacific Accessory Corporation -Sa nta Ana, CA 92705
OnStar
®
Active
Right Fron t
Left Fr ont
Factory 9 pin wire harness
Factory 21 pin wire harness
OEM-1 Premium Sound Interface
OS-1 OnStar® Interface
OS-1618
AMP-GM21A harness -or-
AMP-GM21B (Pontiac Grand Prix only)
(for BOSE only!)
OS-GM9
OS-RAD
102.7 FM
Aftermarket stereo
Connecting the aftermarket stereo and OS-1 to the vehicle’s factory Bose system.
Step 1.
Pre wire the OS-RAD wire harness to the aftermarket stereo wire harness. If the aftermarket stereo has a mute wire, cut the
brown wire as close as possible to the relay socket and connect it to the stereo’s mute wire (Fig. 1).
Step 2.
Use the supplied OS-1618 wire harness and connect to the 16 pin connector side to the OS-1. Connect the AMP-GM21A
wire harness and OEM-1 interface to the OS-1 according to diagram below. Connect the AMP-GM21A and OS-GM9 con-
nectors to the factory harness.
NOTES:
WARNING!
(Vehicles equipped with a 9 pin Y connector) Do not unplug the separate 9 pin female and male connectors that are
located farther back in the dash. Doing so will disconnect OnStar® from the OS-GM9 connector.
• Remember to reset OnStar® by turning the ignition off for at least two minutes prior to testing.
• The AMP-GM21A wire harness will ONLY work on a vehicle with a BOSE premium sound system.
Page
2
Pacifi c Accessory Corporation - 1502 S. Santa Fe Street, Santa Ana, CA 92705
techsupport@pac-audio.com • Voice: 714-835-3022 • Fax: 714-835-3233 • www.pac-audio.com
Important! Reset OnStar® by turning the ignition off for at least two minutes prior to testing.
Step #1: Adjusting the OEM-1 level controls.
After all connections are made and plugged in, turn on the aftermarket stereo. Adjust the volume on the radio and the OEM-1 level
controls to a suitable undistorted listening level. The OEM-1 can be adjusted with a small fl at head screwdriver.
Step #2: Adjusting OS-1 Volume and Testing Operation with OnStar
®
After all connections are made, push the Blue OnStar
®
button on the vehicle to initiate a call to the service center. The OS-1 LED
will turn on and the the stereo should either mute or turn off and a greeting message should be heard. Adjust the OS-1 volume to
a suitable loudness level. Adjust the audio outputs of the OS-1 with a small fl at head screwdriver. Counter clockwise is at minimum
and clockwise is maximum output. If the volume sounds distorted, lower the outputs of the OS-1. Pressing the black OnStar
®
button on the vehicle will end the call and the OS-1 LED will turn off. After a few seconds the stereo should resume playing or will
turn back on.
Testing and Verifying Operation
Fig. 1
WIRE COLOR CIRCUIT CIRCUIT WIRE COLOR
WHITE/BLACK LEFT FRONT(-) 9 18 MUTE BROWN
GRAY/BLACK RIGHT FRONT (-) 8 17 LEFT FRONT (+) WHITE
GREEN/BLACK LEFT REAR (-) 7 16
PURPLE/BLACK RIGHT REAR (-) 6 15 RIGHT FRONT (+) GRAY
BLACK GROUND 5 14
BLUE POWER ANTENNA 4 13 LEFT REAR (+) GREEN
ORANGE ILLUMINATION 3 12
BLUE/WHITE AMP TRIGGER 2 11 RIGHT REAR (+) PURPLE
RED 12V SWITCHED/ACC 1 10 12V CONSTANT YELLOW
PIN NUMBER
18 pin OS-RAD Input harness
Looking from wire side of plugs
WIRE COLOR CIRCUIT CIRCUIT WIRE COLOR
ORANGE ILLUMINATION 8 16 12V SWITCHED/ ACC RED
BLUE/WHT AMP TRIGGER 7 15 12 CONSTANT YELLOW
BLACK GROUND 6 14 POWER ANTENNA BLUE
PURPLE/BLK RIGHT REAR (-) 5 13 RIGHT REAR (+) PURPLE
GREEN/BLK LEFT REAR (-) 4 12 LEFT REAR (+) GREEN
N/C 3 11 N/C
GRAY/BLK RIGHT FRONT (-) 2 10 RIGHT FRONT (+) GRAY
WHITE/BLACK LEFT FRONT (-) 1 9 LEFT FRONT (+) WHITE
PIN NUMBER
16 pin AMP-GM21A output harness
Pop white locking clip out on the OS-
GM9 connector in the location of the
green wire by using a small flat head
screw driver.
Insert paper clip into the slot above
pin of the OS-GM9 connector and
push metal clip down while gently
pulling on green wire. If done
correctly, wire will pull out easily.
Bulletin*
1998-2003 Pontiac Grand Prix, 1998-2000 GMC Yukon Denali, 1999-2000 Cadillac Escalade (not for 2002 Escalade)
Relocate the green wire in the OS-GM9 connector prior to installation of the OS-1. The green wire will need to go into pin#15
of the AMP-GM21A , AMP-GM21B or AMP-GM21C connector as shown in diagrams below.
Insert green wire into pin#15 of the
OS-GM21 (Grand Prix non/BOSE) or
OS-GM21A (Escalade/Yukon Denali)
connector.
1999-2000
Pontiac Grand Prix
w/BOSE requires a AMP-GM21B
and
2001-2003 Grand Prix requ
res the AMP-
GM21C
wire harness, not a AMP-GM21A
harness.
30
85
86
87
87A
Brown
Red
Cut brown wire as close as possible to socket
and connect it to the stereo's mute wire.
Red
OS-RAD
You may remove the relay and socket by cutting
the red wire at the heatshrink and connect
it to the stereo's accessory wire.

Tuotetiedot

Merkki: PAC
Kategoria: Ei luokiteltu
Malli: OS-1 BOSE

Tarvitsetko apua?

Jos tarvitset apua merkille PAC OS-1 BOSE esitä kysymys alla ja muut käyttäjät vastaavat sinulle




Ei luokiteltu PAC Käyttöohjeet

PAC

PAC AOEM-GM1416A Käyttöohje

15 Lokakuuta 2024
PAC

PAC SR-TUN14H Käyttöohje

15 Lokakuuta 2024
PAC

PAC AOEM-HON20 Käyttöohje

15 Lokakuuta 2024
PAC

PAC TVC104 Käyttöohje

15 Lokakuuta 2024
PAC

PAC CDK651 Käyttöohje

15 Lokakuuta 2024
PAC

PAC MAZATO Käyttöohje

15 Lokakuuta 2024
PAC

PAC AOEM-GM21C Käyttöohje

15 Lokakuuta 2024
PAC

PAC APSUB-TY12 Käyttöohje

15 Lokakuuta 2024
PAC

PAC LPGL-2 Käyttöohje

15 Lokakuuta 2024
PAC

PAC GMK403 Käyttöohje

15 Lokakuuta 2024

Ei luokiteltu Käyttöohjeet

Viimeisimmät Ei luokiteltu Käyttöohjeet