PAC OS-5 Käyttöohje

Lue alta 📖 käyttöohje suomeksi merkille PAC OS-5 (4 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 4 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/4
OS-5
Radio Replacement Interface with
Telematics Retention
For select General Motors Vehicles
With 29 Bit Data Systems
© 2021 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Rev: V1
Date: 12/17/2021 Page 1
Introduction and Features
Important Notes
1. Aftermarket radio must have an auxiliary input in order to retain RSE audio.
2. If the vehicle chimes when the radio is removed, the CMX is not necessary. In order to get the best possible sound out of the
CMX, please mount it in a place free and clear of any obstructions, preferably as close as possible to the bottom of the dash
pointing down toward the oor of the vehicle.
Module Layout
Programming Button
USB Port
Radio Select DIP switches
Interface Connector 4
Adjustment Dial
Module Status LED
USB Status LED
Interface Connector 1
Not Used
Interface Connector 2
Amplied Audio Output Connector 3
Non-Amplied Audio Output
The OS-5 interface allows the replacement of a factory radio in select General Motors vehicles with 29 Bit Data-Bus. Using this
interface will retain factory features such as Warning Chimes, Bose Amplier, Rear Seat Entertainment (RSE), and Rear Seat
Controls (RSC) when the original radio is removed. The OS-5 provides data bus driven outputs such as retained accessory power
(RAP), vehicle speed signal (VSS), illumination, reverse trigger and parking brake.
OS-5
Radio Replacement Interface with
Telematics Retention
For select General Motors Vehicles
With 29 Bit Data Systems
© 2021 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Rev: V1
Date: 12/17/2021 Page 2
Installation Steps
1. Wire your aftermarket radio to the OS-5’s harness according to the wiring connections chart below.
2. The Brown mute loop in Interface Connector 4 (if not cut) will turn the OS-5’s accessory output off when any OnStar
function is active. If the aftermarket radio has a mute input, cut this loop and connect the Brown wire in pin 23 to it. This pin
is located in the top row next to the solid blue wire. (The top of the connector has the locking tab on it).
3. Plug Interface Connectors 1 and 2 into the appropriate ports on the OS-5 interface (using the diagram on Page 1 or the
label on the bottom of the interface).
4. The Connector 3 connection will be dependent upon whether or not the vehicle has a factory amplied system. Plug this
connector into the appropriate port on the OS-5 (using the diagram on Page 1 or the label on the bottom of the interface).
5. If the aftermarket radio is equipped with an auxiliary input and you wish to retain the factory RSE audio, you must use the
part# GMRVD (Sold Separately).
6. Remove the factory radio and plug in the OS-5’s Vehicle and Vehicle Connector 1 Connector 2 into the factory vehicle
harness.
7. Plug the 2-Pin connector into the CMX Chime Module (If the vehicle chimes when the radio is removed, the CMX is not
necessary). PLEASE NOTE: In order to get the best possible sound out of the CMX, please mount it in a place free and clear
of any obstructions, preferably as close as possible to the bottom of the dash pointing down toward the oor of the vehicle.
Interface Connector 1
(3-pin)
Interface Connector 2
(20-pin)
Interface Connector 4
(24-pin)
Interface Connector 3
(12-pin)
Yellow 12v+
Red Accessory Output
(10 amp)
Black Ground
Brown Loop Mute Output
Blue Not Used
Blue / White Remote On Input
Orange Not Used
Orange / White Illumination Output
Purple / White Reverse Output (+)
Light Green Parking Brake Output (-)
Pink Vehicle Speed Signal
(VSS) Output
Blue / Yellow SWC Output / Key 1
Brown SWC Output / Key 2
3.5 mm Jack SWC Output
Purple Rear R + input
Purple / Black Rear R - input
Green Rear L + input
Green / Black Rear L - input
Gray Front R + input
Gray / Black Front R - input
White Front L + input
White / Black Front L - input
Wiring Connections
CMX Chime Module
Vehicle Connector 1
(14-pin)
Vehicle Connector 2
(16-pin)
OS-5
Radio Replacement Interface with
Telematics Retention
For select General Motors Vehicles
With 29 Bit Data Systems
© 2021 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Rev: V1
Date: 12/17/2021 Page 3
Programming Button and Adjustment Dial Functions
You can press and hold the programming button on the side of the interface to access different programming modes. Once the
LED is lit to the mode you desire (see below for modes), immediately release the programming button to access that mode.
PLEASE NOTE:
• This process must be done with the interface in the vehicle and the key in the ignition position.
A. LED 1 ash red: Master reset. This does a master reset of the interface and restores the following settings to factory
defaults:
SWC Mapping
SWC Calibration
SWI-DIRECT Steering Wheel Control Output Connector
If you are using the SWI-RC-1 or SWI-CP2 please follow the steps below.
Refer to the gure to the right to set the bank of eight Dip-Switches.
Refer to the guide below for setting the bank of four Dip-Switches based on your radios manufacturer.
Set DIP-Switches that correspond with your radio to the ON position.
Set all other DIP-Switches to the OFF position.
If your brand is not listed above, please use “ALL OTHER BRANDS.”
Alpine JVC
Kenwood /
Lightning
Audio
Stinger Clarion /
Nakamichi
All Other
Brands Pioneer Sony Fusion
1 2 1 & 2 3 3 1, 2, & 3 1, 2, & 3 4 1 & 4
Testing and Verication
1. Turn the ignition on. LED 1 will illuminate red and the +12v accessory wire will turn on.
2. Turn on the radio and check chimes, volume, balance, and fader.
3. In vehicles equipped with Premium Bose (Y91 / UQA): If the overall volume is too low, use the adjustment dial on the side of
the interface to set it to the desired level. The best way to do this is to turn the volume on the radio to 3/4 volume, then turn the
adjustment dial on the OS-5 clockwise until some distortion is heard, then
counter-clockwise a little.
4. To adjust OnStar volume, press the OnStar button on the mirror then use the
volume buttons on the SWC, or the adjustment dial on the side of the module
to adjust the level. When you hear a chime during this process it means you
have reached the farthest minimum / maximum level.
5. Pressing the OnStar button on the rearview mirror will turn off the rear speakers
and allow the OnStar audio to be heard in the two front speakers. The OnStar
active LED will also turn on. When OnStar disconnects, the radio will un-mute
or turn back on and the OnStar LED will turn off. Pressing the VR / OnStar
button on the steering wheel will also activate OnStar.
6. Turn off vehicle and remove key. RAP will be active and keep the radio on for 10 minutes or until any door is opened.
7. The LED and radio will turn off when RAP turns off or until any door is opened.
8. Use the 4-position selector switch located on the side of the CMX chime module to select the best chime output volume for your
specic installation. Setting 1 being loudest and 4 being softest.
CMX
chime module
1
4
2
3
OnStar Volume Adjustment for Vehicles without SWC
Adjustment Dial
1. When OnStar is active use the adjustment dial on the side
of the module to raise or lower the OnStar volume to the
desired level.

Tuotetiedot

Merkki: PAC
Kategoria: Ei luokiteltu
Malli: OS-5

Tarvitsetko apua?

Jos tarvitset apua merkille PAC OS-5 esitä kysymys alla ja muut käyttäjät vastaavat sinulle




Ei luokiteltu PAC Käyttöohjeet

PAC

PAC AOEM-GM1416A Käyttöohje

15 Lokakuuta 2024
PAC

PAC SR-TUN14H Käyttöohje

15 Lokakuuta 2024
PAC

PAC AOEM-HON20 Käyttöohje

15 Lokakuuta 2024
PAC

PAC TVC104 Käyttöohje

15 Lokakuuta 2024
PAC

PAC CDK651 Käyttöohje

15 Lokakuuta 2024
PAC

PAC MAZATO Käyttöohje

15 Lokakuuta 2024
PAC

PAC AOEM-GM21C Käyttöohje

15 Lokakuuta 2024
PAC

PAC APSUB-TY12 Käyttöohje

15 Lokakuuta 2024
PAC

PAC LPGL-2 Käyttöohje

15 Lokakuuta 2024
PAC

PAC GMK403 Käyttöohje

15 Lokakuuta 2024

Ei luokiteltu Käyttöohjeet

Viimeisimmät Ei luokiteltu Käyttöohjeet