PAC TOYK969 Käyttöohje

PAC Ei luokiteltu TOYK969

Lue alta 📖 käyttöohje suomeksi merkille PAC TOYK969 (6 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 4 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/6
CUSTOMER HELP LINE
USA 800-323-4329 • Canada 800-245-8777
TOYK969 Mounting Kit
Toyota
2007-14 FJ CRUISER
2007-14 YARIS (Excluding radio w/2”x4” LCD display)
Scion
2004-06 xA
2004-14 xB
2008-14 xD
2005-10 TC
VEHICLE APPLICATIONS
iTOYK969 ©2015 AMERICAN INTERNATIONAL INDUSTRIES, INC. TECH Ver. 10/14 PRINT Ver. 04/15
WWW.AIUS.NET
2500 East Francis Street Ontario, CA 91761, U.S.A.
USA Sales (800) 336-6500
Canada Sales (888) 922-3006
For information about other American International automotive
accessories visit our website at:
http://www.aius.net
1
DIN MOUNT INSTRUCTIONS
1. Follow instructions from steps 1&2 of ISO mount instructions below.
2. Insert DIN sleeve from your new radio into the upper section of the installation kit.
(This DIN sleeve comes with all new radios and slides off the back of the radio)
3. Depress the tabs from inside the sleeves opening upward, outward, and downward
to secure sleeve to the installation kit.
4. Install radio into sleeve and lock into place.
Optional use Trim Ring (ITR-969) may be used on some radios if desired.
Due to the movement of some faces on some radios our ISO Trim Ring may not be able
to be used. You may also ISO mount your radio. Your new radio must have a trim ring
around the face of the radio that is designed to be easily removed. Consult your radio
ownerʼs manual.
ITR-969
Trim Ring
(Optional Use)
ISO MOUNT INSTALLATION INSTRUCTIONS
Not e: Some radio faces are larger in size than the ITR-969 Trim Ring allows.
You may need to file the Trim Ring opening larger for some radios.
1. Attach the left and right side brackets to the main bracket. See illustration below.
2. Attach left and right side brackets to the rear of the pocket using screws supplied w/kit.
3. Attach ISO Mount Spacers to the inside of upper section on
both Left & Right mounting brackets as shown in Figure A.
4. Slide radio into kit from rear & attach to ISO mounting
brackets using screws supplied with radio (do not tighten
screws at this time). (Be sure the length of the screws
DO NOT touch any electrical parts inside radio, some
screws may need to be shortened.)
5. Slide radio forward or backward for your desired look and
then tighten the mounting screws. Use ISO trim ring
when possible.
NOTE: Optional ISO trim ring (ITR-969 included)
may be used in place of after-market radioʼs
trim ring. For ISO mount applications,
mount after-market radio
to side brackets using
hardware included. ITR-969
Trim Ring
(Optional Use)
Fig. A
DINSleeve
10
1. Carefully unclip and remove the soft trim piece from around the radio, airbag
light/hazard button and passenger side air vent.
2. Carefully unclip and pry forward the radio trim bezel.
3. Remove the (4) Phillips screws securing the radio to the sub-dash.
4. Pull radio forward, disconnect the attached wire harness and antenna lead
and remove radio.
DASH DISASSEMBLY
2012-14 TOYOTA YARIS
KIT ASSEMBLY
FOR ISO or DIN MOUNT APPLICATIONS SEE PAGE 1
REMOVE SHADED MOUNTING
TABS ON BOTH LEFT AND
RIGHT SIDES OF KIT
1. Prepare mounting brackets as shown below.
ATTACH BRACKETS TO REAR OF
POCKET USING SCREWS SUPPLIED
FOR ISO or DIN MOUNT APPLICATIONS SEE PAGE 1
KIT ASSEMBLY
KEEP SHADED MOUNTING TABS
ON BOTH LEFT AND RIGHT
BRACKETS.
REMOVE ALL OTHERS.
Optional use
ITR 969
IMB 969L
IMB 969R
1. Prepare mounting brackets as shown below.
ATTACH BRACKETS TO REAR OF
POCKET USING SCREWS SUPPLIED
FOR ISO or DIN MOUNT APPLICATIONS SEE PAGE 1
KIT ASSEMBLY
REMOVE SHADED MOUNTING
TABS ON BOTH LEFT AND
RIGHT BRACKETS
Optional use
ITR 969
IMB 969L
IMB 969R
2
1. Carefully pull outward on the left and right (rotary) climate control knobs
and remove the phillips screw from behind each knob.
2. Carefully unclip and remove the side trims from beside the climate
controls, ashtray, and pocket.
3. Remove the (2) phillips screws securing the lower edges of the climate control/radio
trim bezel to the sub-dash.
4. Carefully pry outward on the Climate control/radio trim bezel, disconnect all
harnesses and remove trim bezel.
5. Remove the (4) Phillips screws securing the factory radio to the sub-dash.
Carefully pull radio forward, disconnect the wire harness and antenna
lead from the radio and remove radio.
DASH DISASSEMBLY
2004-06 TOYOTA SCION xA
9
1. Carefully unsnap the rectangle bezel surrounding the factory radio
2. Remove (4) 10mm bolts securing the factory radio in
3. Disconnect all harnesses and remove radio from dash
DASH DISASSEMBLY
2008-14 TOYOTA SCION xB

Tuotetiedot

Merkki: PAC
Kategoria: Ei luokiteltu
Malli: TOYK969

Tarvitsetko apua?

Jos tarvitset apua merkille PAC TOYK969 esitä kysymys alla ja muut käyttäjät vastaavat sinulle




Ei luokiteltu PAC Käyttöohjeet

PAC

PAC AOEM-GM1416A Käyttöohje

15 Lokakuuta 2024
PAC

PAC SR-TUN14H Käyttöohje

15 Lokakuuta 2024
PAC

PAC AOEM-HON20 Käyttöohje

15 Lokakuuta 2024
PAC

PAC TVC104 Käyttöohje

15 Lokakuuta 2024
PAC

PAC CDK651 Käyttöohje

15 Lokakuuta 2024
PAC

PAC MAZATO Käyttöohje

15 Lokakuuta 2024
PAC

PAC AOEM-GM21C Käyttöohje

15 Lokakuuta 2024
PAC

PAC APSUB-TY12 Käyttöohje

15 Lokakuuta 2024
PAC

PAC LPGL-2 Käyttöohje

15 Lokakuuta 2024
PAC

PAC GMK403 Käyttöohje

15 Lokakuuta 2024

Ei luokiteltu Käyttöohjeet

Viimeisimmät Ei luokiteltu Käyttöohjeet