Philips EasyCare GC3220 Käyttöohje
Lue alta 📖 käyttöohje suomeksi merkille Philips EasyCare GC3220 (10 sivua) kategoriassa Rauta. Tämä opas oli hyödyllinen 6 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/10
GC3260, GC3240, GC3232, GC3231, GC3230,
GC3221, GC3220
2345
6789
10 11 12 13
14 15
General Description (fig.1).
ASpray nozzle
BFilling opening with cap
CShot-of-steam button
DSpray button
ESteam control
FTemperature light
GCalc-Clean button
HTemperature dial
ICord
JHeel
KWater tank
Important.
Read these instructions for use carefully before using the appliance and save
them for future reference.
◗Check if the voltage indicated on the appliance corresponds to your
electrical supply before plugging in the appliance.
◗If the appliance is provided with an Earth Plug, it must be plugged into
an earthed socket.
◗Do not use the appliance if it has been dropped, if the plug, the cord
or the appliance itself shows visible damage or if it is leaking.
◗Regularly check if the mains cord is still undamaged and safe.
◗If the main cord is damaged, it must be replaced by Philips or its
service agent or a similarly qualified person in order to avoid a hazard.
◗Never leave the appliance unattended when it is connected to the mains.
◗Never immerse the iron in water.
◗Infirm persons should not be allowed to use the appliance without
supervision. Keep the appliance out of the reach of children.
◗The soleplate of the iron can become extremely hot and may cause
burns if touched.
◗Do not allow the cord to come into contact with the soleplate when it
is hot.
◗When you have finished ironing, when you clean the appliance, when
you fill or empty the water tank and also when you leave the iron even
for a short while: set the steam control to position 0, put the iron on
its heel and remove the mains plug from the wall socket.
◗Always place and use the iron on a stable, level and horizontal surface.
◗If a stand is provided with the appliance, ensure that the stand is placed
on a stable surface.
◗This appliance is intended for household use only.
Before first use.
1Remove any sticker, protective foil or plastic shield from the soleplate
(fig. 2).
BThe iron may give off some smoke when you use it for the first time. This will
cease after a short while.
Preparing for use.
Filling the water tank
1Make sure the appliance is unplugged.
2Set the steam control to position 0 (= no steam) (fig. 3).
3Open the cap of the filling opening.
4Tilt the iron backwards and fill the water tank with tap water up to the
maximum level by means of the filling cup (fig. 4).
Do not fill the tank beyond the MAX indication.
Do not put perfume, vinegar, starch, descaling agents, ironing additives,
chemically descaled water or other chemicals in the water tank.
5Close the cap of the filling opening ('click').
Setting the temperature
1Put the iron on its heel and set the required ironing temperature by
turning the temperature dial to the appropriate position (fig. 5).
Check the laundry care label for the required ironing temperature:
-1Synthetic fabrics (e.g. acrylic, nylon, polyamide, polyester)
-1Silk
-2Wool
-3Cotton, linen
If you do not know what kind or kinds of fabric an article is made of,
determine the right ironing temperature by ironing a part that will not be
visible when you wear or use the article.
ENGLISH
Silk, woollen and synthetic materials: iron the reverse side of the fabric to
prevent shiny patches. Avoid using the spray function to prevent stains. Start
ironing the articles that require the lowest ironing temperature, such as those
made of synthetic fibres.
2Put the mains plug in an earthed wall socket.
3When the temperature light has gone out, wait a while before you
start ironing (fig. 6).
The temperature light will go on from time to time during ironing.
Using the appliance.
Steam ironing
1Make sure that there is enough water in the water tank.
2Select the recommended ironing temperature (see chapter 'Preparing
for use', section 'Setting the temperature').
3Select the appropriate steam setting. Make sure that the steam setting
you select is suitable for the ironing temperature selected: (fig. 7).
- 1 - 2 for moderate steam (temperature settings to 2 3)
- 3 - 4 for maximum steam (temperature settings to MAX)3
BThe iron will start steaming as soon as the set temperature has been
reached.
BIf the selected ironing temperature is too low (MIN to ), water may drip2
from the soleplate (see section 'Drip stop').
Ironing without steam
1Set the steam control to position 0 (= no steam) (fig. 3).
2Select the recommended ironing temperature (see chapter 'Preparing
for use', section 'Setting the temperature').
Features.
Spray function
You can use the spray function to remove stubborn creases at any temperature.
1Make sure that there is enough water in the water tank.
2Press the spray button several times to moisten the article to be
ironed (fig. 8).
Shot of steam
A powerful shot of steam helps to remove stubborn creases.
The shot-of-steam function can only be used at temperature settings
between and MAX.2
1Press and release the shot-of-steam button (fig. 9).
Concentrated shot of steam from the special Steam Tip
(types GC3260 and GC3240 only)
The forward-directed concentrated shot of steam enhances the distribution
of steam into every part of your garment. The concentrated shot-of-steam
function can only be used at temperature settings between and MAX.2
1Press and release the shot-of-steam button (fig. 10).
Vertical shot of steam
1The shot-of-steam function can also be used when you hold the iron in
vertical position (fig. 11).
This is useful for removing creases from hanging clothes, curtains etc.
Never direct the steam at people.
Drip stop (types GC3260, 3240, 3232, 3231, 3230 only)
This iron is equipped with a drip-stop function: the iron automatically stops
producing steam when the temperature is too low to prevent water from
dripping out of the soleplate. When this happens you may hear a sound.
Electronic safety shut-off function (type GC3260 only)
◗The electronic safety shut-off function automatically switches the iron
off if it has not been moved for a while (fig. 6).
4239 000 59323
2/10
◗The auto-off light starts blinking to indicate that the iron has been
switched off by the safety shut-off function.
To let the iron heat up again, pick it up or move it slightly. The auto-off light
will go out.
- If the temperature light goes on, wait for it to go out before you start
ironing.
- If the temperature light does not go on, the iron is ready for use.
Cleaning and maintenance.
After ironing
1Remove the mains plug from the wall socket and let the iron cool down.
2Clean the appliance with a damp cloth. Wipe any scale or deposits off
the soleplate with a non-abrasive (liquid) cleaner.
3Empty the water tank after cleaning (fig. 12).
4Leat the iron cool down. Wind the mains cord round the cord storage
facility and fix it with the cord clip.
5Always store the iron standing on its heel in a safe and dry place (fig. 13).
Double-Active Calc System
The Double-Active Calc System guarantees a longer life for the iron.
◗The anti-calc tablets prevent scale from clogging the steam vents. The
tablets are constantly active and do not need to be replaced (fig. 14).
◗The Calc-Clean function helps remove scale particles. Use the Calc-
Clean function once every two weeks. If the water in your area is very
hard (i.e. when flakes come out of the soleplate during ironing), the
Calc-Clean function should be used more frequently.
1Make sure the appliance is unplugged.
2Set the steam control to position 0.
3Fill the water tank to the maximum level.
Do not put vinegar or other descaling agents in the water tank.
4Select the maximum ironing temperature.
5Put the plug in the wall socket.
6Unplug the iron when the temperature light has gone out.
7Hold the iron over the sink, press and hold the Calc-Clean button and
gently shake the iron (fig. 15).
Steam and boiling water will come out of the soleplate. Impurities and flakes
(if any) will be flushed out.
8Release the Calc-Clean button as soon as all the water in the tank has
been used up.
Repeat the Calc-Clean process if the iron still contains a lot of impurities.
After the Calc-Clean process
- Put the plug in the wall socket and let the iron heat up to allow the
soleplate to dry.
- Unplug the iron when the temperature light has gone out.
- Move the hot iron gently over a piece of used cloth to remove any water
stains that may have formed on the soleplate.
- Let the iron cool down before you store it.
Guarantee & service.
If you need information or if you have a problem, please visit the Philips
website at www.philips.com or contact the Philips Customer Care Centre in
your country (you will find its phone number in the worldwide guarantee
leaflet). If there is no Customer Care Centre in your country, turn to your
local Philips dealer or contact the Service Department of Philips Domestic
Appliances and Personal Care BV.
Troubleshooting.
This chapter summarises the most common problems you could encounter
with your iron. Please read the different sections for more details. If you are
unable to solve the problem, contact the Customer Care Centre in your
country.
Solution
Check the mains cord, the
plug and the wall socket.
Set the temperature dial
to the required position.
Fill the water tank (see
chapter 'Preparing for use').
Set the steam control to a
position between 1 and 4
(see chapter 'Using the
appliance').
Select an ironing
temperature that is
suitable for steam ironing
(2 to MAX). Put the
iron on its heel and wait
until the temperature light
has gone out before you
start ironing.
Continue ironing in
horizontal position and
wait a while before using
the (vertical) shot-of-
steam function again.
Select an ironing
temperature that is suitable
for steam ironing (2 to
MAX). Put the iron on its
heel and wait until the
temperature light has gone
out before you start
ironing.
Press the cap until you
hear a click.
Rinse the water tank and
do not put any additive in
the water tank.
Set the temperature dial to
a temperature suitable for
steam ironing (between
3 and MAX). Put the
iron on its heel and wait
until the temperature light
has gone out.
Use the Calc-Clean
function one or more
times (see chapter
'Cleaning and
maintenance').
Move the iron slightly to
deactivate the safety shut-
off function. The light goes
out.
Empty the water tank and
set the steam control to
position 0 after use. Store
the iron on its heel.
Possible cause
There is a connection
problem.
The temperature dial has
been set to MIN.
There is not enough water
in the water tank.
The steam control has
been set to position 0.
The iron is not hot enough
and/or the drip-stop
function has been
activated.
The (vertical) shot-of-
steam function has been
used too often within a
very short period.
The iron is not hot
enough.
The cap of the filling
opening has not been
closed properly.
An additive has been
poured into the water
tank.
The iron is not hot
enough.
Hard water forms flakes
inside the soleplate.
The safety shut-off function
has switched the iron off
(see chapter 'Features').
The iron has been put in
horizontal position with
water still left in the water
tank.
Problem
The iron is plugged in but
the soleplate is cold.
No steam.
No shot of steam or no
vertical shot of steam.
Water droplets drip onto
the fabric.
Flakes and impurities come
out of the soleplate during
ironing.
The light blinks (type
GC3260 only).
Water drips from the
soleplate after the iron has
cooled down or has been
stored.
4239 000 59323
3/10
Tuotetiedot
| Merkki: | Philips |
| Kategoria: | Rauta |
| Malli: | EasyCare GC3220 |
Tarvitsetko apua?
Jos tarvitset apua merkille Philips EasyCare GC3220 esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Rauta Philips Käyttöohjeet
19 Lokakuuta 2024
15 Lokakuuta 2024
15 Lokakuuta 2024
15 Lokakuuta 2024
Rauta Käyttöohjeet
- Rauta Imarflex
- Rauta Sunbeam
- Rauta Orbegozo
- Rauta Khind
- Rauta Hyundai
- Rauta Ufesa
- Rauta Eldom
- Rauta Black And Decker
- Rauta Hamilton Beach
- Rauta Di4
- Rauta Mellerware
- Rauta Girmi
- Rauta Camry
- Rauta Yamazen
Viimeisimmät Rauta Käyttöohjeet
23 Lokakuuta 2024
22 Lokakuuta 2024
20 Lokakuuta 2024
20 Lokakuuta 2024
20 Lokakuuta 2024
20 Lokakuuta 2024
20 Lokakuuta 2024
20 Lokakuuta 2024
20 Lokakuuta 2024
20 Lokakuuta 2024