Sharp NU-AC310 Käyttöohje

Sharp Ei luokiteltu NU-AC310

Lue alta 📖 käyttöohje suomeksi merkille Sharp NU-AC310 (8 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 14 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Lataa PDF

Sivu 1/8

SIM01E- 2 00

PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING OR USING THE MODULES.

PLEASE PASS ALONG THE ATTACHED USER MANUAL TO YOUR CUSTOMER.

INSTALLATION MANUAL

– – Crystalline Photovoltaic Module

# IMPORTANT SAFETY INSTRUCTIONS p.1

# GENERAL INSTRUCTIONS 1 ~ p.3 p.

# INSTALLATION MANUAL -PHOTOVOLTAIC MODULES- 4 p.

# ELECTRICAL OUTPUT AND THERMAL CHARACTERISTICS 4 p.

IMPORTANT SAFETY INSTRUCTIONS

This manual contains important safety instructions for the PV module

that must be followed during the maintenance of PV modules.

To reduce the risk of electric shock, do not perform any servicing

unless you are qualied to do so.

1. The installation must be performed by a certied installer

/servicer to ensure system integrity and safety.

2. The installation is only allowed after referring and

understanding of GENERAL INSTALLATION MANUAL and

INSTALLATION MANUAL -PHOTOVOLTAIC MODULE-. If you

don’t have your personal copy, please contact your installer or

local Sharp oce listed in Sharp Solar web site : URL :

http://www.sharp-world.com/solar

3. Do not pull the PV cables.

4. Do not touch any surface of module.

5. Do not place/drop objects onto the PV modules.

6. Do not disassemble or attempt to repair the PV module by

yourself.

7. Do not drop the PV module.

8. Do not damage, pull, bend, or place heavy material on cables.

9. Upon completion of any service or repairs, ask the

installer/servicer to perform routine checks to determine that

the PV modules are in safe and proper operating condition.

10. When replacement parts are required, be sure the

installer/servicer uses parts specied by the manufacturer with

same characteristics as the original parts. Unauthorized

substitutions may result in re, electric shock, or other hazard.

11. Consult your local building and safety department for required

permits and applicable regulations.

12. In regions with snow, the module can sustain a snow load of up

to 50cm (when the module is mounted in the portrait orientation

/ short frame side facing down) or 100cm (when the module is

mounted in the landscape orientation / long frame side facing

down).

13. As a result of sliding snow, the mechanical load increases when

the number of module rows in the matrix of a PV installation

increases. When mounting the module in the portrait orientation

for more than 3 rows, the accumulated snow load may cause

the lower edge of the module frame to deform. Take necessary

measures (e.g. snow stopper) to avoid possible damage.

14. Periodically remove any overhanging snow and/or ice from the

module framework as it may cause deformation of the module

frame.

GENERAL INSTRUCTIONS

1. INTRODUCTION

This Installation Manual contains essential information for the electrical and mechanical installation that you must know before

installing SHARP PV modules. This also contains safety information you need to be familiar with. All the information described in

this manual are the intellectual property of SHARP and based on the technologies and experiences that have been acquired and

accumulated in the long history of SHARP. This document does not constitute a guaranty, expressed or implied. SHARP does not

assume responsibility and expressly disclaims liability for loss, damage, or expense arising out of or in any way connected with

installation, operation, use or maintenance of the PV modules. No responsibility is assumed by SHARP for any infringement of

patents or other rights of third parties that may result from use of PV module. SHARP reserves the right to make changes to the

product, specications or installation manual without prior notice.

2. COMPONENTS

3. GENERAL INFORMATION

(INCLUDING WARNING AND SAFETY)

The installation of PV modules requires a great degree of skill

and should only be performed by a qualied licensed

professional, including licensed contractors and licensed

electricians. Please be aware that there is a serious risk of

various types of injury occurring during the installation including

the risk of electric shock. All SHARP PV modules are equipped

with a permanently attached junction box that will accept variety

of wiring applications or with a special cable assembly for ease

of installation, and they do not require special assembly.

GENERAL WARNING

1. PV modules are heavy. Handle with care.

2. Before you attempt to install, wire, operate and maintain

the PV module, please make sure that you completely

understand the information described in this installation

manual.

3. Contact with electrically active parts of a PV module such

as terminals can result in burns, sparks and lethal shock

MODEL

NU NU- ,AC*** -AC***B,ND-AC series ***

CAUTION: HIGH VOLTAGE

To reduce the risk of electric shock, do not touch.

Superstrate Glass

Junction box

Frame

Solar Photovoltaic Cell

Connector

Electriclal Cable

SIM01E- 2 00

whether the PV modules connected or not. are

4. PV modules produce electricity when the sucient sunlight

or other sources illuminate the module surface. When the

modules are connected in series, voltage is cumulative.

When the modules are connected in parallel, current is

cumulative. As a result, a large-scale PV system can

produce high voltage and current which could present an

increased hazard and may cause serious injury or death.

5. Do not connect the PV modules directly to the loads such

as motor since the variation of the output power depending

on the solar irradiation causes damage for the connected

motor.

1: In the case of a brushless motor, the lock function

becomes active and the hall IC is most likely to be

damaged.

2: In the case of a brush type motor, the coil is most likely

to be damaged.

6. In case of snow build-up, snow would slide easier on the

smooth surface of the module than other parts of the roof.

Snow may suddenly slide, fall o the roof and hit nearby

objects/areas. Take preventive measures (e.g. snow

stopper) when there is possible risk such case would

cause an injury or a damage.

GENERAL SAFETY

1. Consult local codes and other applicable laws concerning

required permits on regulations installation and for

inspection requirements.

2. Before installing a PV module, contact appropriate

authorities to determine permit, installation and inspection

requirements that should be followed.

3. Install PV modules and ground frames in accordance with

applicable rules and regulations.

4. PV modules should be installed and maintained by

qualied personnel. Only installer/servicer personnel

should have access to the PV module installation site.

5. No matter where the PV modules are installed, either roof

mounted construction or any other type of structures above

the ground, appropriate safety practices should be

followed and required safety equipment should be used in

order to avoid possible safety hazards. Note that the

installation of some PV modules on roofs may require the

addition of reproong, depending on local building/re

codes.

6. In the case that the PV modules are non-integral type, the

module is to be mounted over a re resistant roof.

7. e PV modules with Us the same cell size within series.

8. Follow all safety precautions of other components that are

used in the system.

9. In order to avoid a risk of injury or electrical shock, do not

allow anyone to approach the PV module if the person has

little knowledge on PV module or on the measures that

should be taken when PV modules are damaged.

10. Do not shade portions of the PV module surface from the

sunlight for a long time. The shaded cell may become hot

(hot spot phenomenon) which results in solder joints

peeling o. Shading causes drop in generated power

and/or operation failure of the PV modules.

11. Do not clean the glass surface with chemicals. Do not let

water collect on the glass surface for a long time. This

creates a risk of white eorescence (glass disease) which

may result in the deterioration of energy generation.

12. Do not install the PV module horizontally. It may cause dirt

or white eorescence (glass disease) due to water.

13. gap Do not cover the water drain of the frame. There is a

risk of frost damage when the frame is lled with water

cumulation.

14. If there is a risk of sliding snow, an appropriate measure

has to be taken so that PV module frames on lower edge

of PV modules will not be damaged.

15. Do not expose PV module to sunlight concentrated with

mirrors, lenses or similar means.

16. Turn o inverters and circuit breakers immediately, should

a problem occur.

17. In case the glass surface of a PV module is broken, wear

goggles and tape the glass to keep the broken pieces in

place.

18. A defective PV module may generate power even if it is

removed from the system. It may be dangerous to handle

the PV module while exposed to sunlight. Place a defective

PV module in a carton so PV cells are completely shaded.

19. In case of series connection, the maximum open circuit

voltage must not be greater than the specied maximum

system voltage. The voltage is proportional to the number

of series. In case of parallel connection, please be sure to

take proper measure (e.g. fuse for protection of module

and cable from over current, and/or blocking diode for

prevention of unbalanced strings voltage) to block the

reverse current flow. The current may easily flow in a

reverse direction.

20. p modules away from children. Kee

HANDLING SAFETY

1. Do not cause an excessive load on the surface of PV

module or twist the frame. The glass surface can easily

break.

2. Do not stand or step on the PV module. The surface glass

of PV module is slippery.

3. Do not hit or put excessive load on the glass or back sheet.

The PV cell is very thin and can be easily broken.

4. Do not scratch or hit at the back sheet. The back sheet is

vulnerable.

5. damage Do not the junction box or do not pull the cables.

The junction box can crack and break.

6. Never touch junction box or the end of output cables with

bare hands when the PV module is irradiated. Cover the

surface of PV module with cloth or other suitable

suciently opaque material to isolate the PV module from

incident light and wear rubber gloves when handling the

wires to avoid electric shock.

7. Do not scratch the output cable or bend it with force. The

insulation of output cable can break and may result in

electricity leakage or shock.

8. Do not pull the output cable excessively. The output cable

may unplug and cause electricity leakage or shock.

9. Do not drill holes in the frame. It may compromise the

frame strength and cause corrosion.

10. Do not scratch the insulation coating of the frame (except

for grounding connection). It may cause corrosion of the

frame or compromise the framework strength.

11. Do not touch the PV module with bare hands. The frame

of PV module has sharp edges and may cause injury.

12. Do not drop PV module or allow objects to fall down on the

PV module.

13. the PV module. Do not concentrate sunlight artificially on

14. Do not hold the PV module one side. The frame may on

bend or twist Hold the PV module at opposite sides. .

INSTALLATION SAFETY

1. Always wear protective head gear, insulating gloves and

safety shoes (with rubber soles). Do not wear metallic

jewellery to prevent electric shock during installation.

2. Keep the PV module packed in the carton until installation.

3. Do not touch the PV module unnecessarily during

installation. The glass surface and the frames get hot.

There is a risk of burn, or electric shock.

4. Do not work under rain, snow or windy conditions.

5. Use dry insulated tools.

6. Do not drop tools or hard objects on PV modules

7. When working at heights, wear a safety belt and take care

not to drop any items (e.g., PV module or tools).

8. Make sure ammable gases are not generated near the

installation site.

9. Completely cover the PV module surface with an opaque

material during PV module installation and wiring.

10. Plug in the connector tight and ensure the wiring work.

Make sure that the connectors have been locked by a

snap-in latch. Any treatments over the connectors which

may allow to unlock the snap-in latch shall not be done.

11. Due to the risk of electrical shock, do not perform any work

if the terminals of PV module are wet.

12. Do not touch the junction box and the end of output cables,

the cable ends (connectors) with bare hands during ,

installation or under sunlight, regardless of whether the PV

module is connected to or disconnected from the system.

13. Do not unplug the connector if the system circuit is

connected to a load.

14. Do not stomp on the glass at work. There is a risk of injury

or electric shock if glass is broken.

15. Do not work alone (always work as a team of 2 or more

people).

16. Do not damage the back sheet of PV modules when setting

the equipotential bonding by bolts.

17. Do not damage the surrounding PV modules or mounting

structure when replacing a PV module.

18. Bind cables by the insulation locks. Drooping down of

cables from the junction box could possibly cause various

problems such as animal biting, electricity leakage in

puddle.

19. Take proper measures for preventing the laminate

(consisted of resin, cells, glass, back sheet, etc.) from

dropping out of the frame in case the glass is broken.

20. e Plastic components such as cables or connectors shall b

located so that they will not be exposed to direct sunlight

after installation to prevent degradation of them.

SIM01E- 2 00

21. If batteries are used with modules, follow safety

precautions of the battery manufacturer.

22. In case of extreme snow build-up, the weight of the snow

may cause the module’s frame to deform. Take appropriate

preventive measures to minimize any possible resulting

damage.

4. SITE SELECTION

In most applications, the PV modules should be installed in a

location where there is no shading throughout the year. In the

Northern Hemisphere, the PV modules should typically face

south, and in the Southern Hemisphere, the PV modules should

typically face north.

Please make sure that there are no obstructions in the

surroundings of the site of installation. TAKE PROPER STEPS

in order to maintain reliability and safety, in case the PV

modules are used in areas such as: Heavy snow areas /

Extremely cold areas / Strong wind areas / Installations over, or

near, water / Areas where installations are prone to salt water

damage/corrosive gas environment/ Small islands or desert

areas.

The results of the ammonia test and the salt-mist-corrosion test

on the modules, carried out under such strict test conditions,

should be disclosed for reference purposes only. The decision

on whether the modules are suitable and compatible for each

installation field will depend on the user’s judgement and

responsibility.

5. TILT ANGLE

The tilt angle is the measurement between the PV module and

a horizontal ground surface. The PV module generates the

maximum output power when it faces the sun directly.

5 degrees or more is recommended for the tilt angle of the PV

module for the maintenance ( 9. Maintenance). See

For the standalone systems with a battery where the PV

modules are attached to a permanent structure, the tilt angle of

the PV modules should be determined to optimize the

performance when the sunlight is the scarcest. In general, if the

electric power generation is adequate when the sunlight is the

scarcest, then the angle chosen should be adequate during the

rest of the year. For grid-connected installations where the PV

modules are attached to a permanent structure, it is

recommended to tilt the PV module at the angle equal to the

latitude of the installation site so that the power generation from

the PV module will be optimum throughout the year.

6. WIRING

To ensure proper system operation and to maintain your

guaranty, observe the correct cable connection polarity (Figures

1 & 2) when connecting the modules to a battery or to other

modules. If not connected correctly, the bypass diode could be

destroyed.

PV modules can be wired in series to increase voltage.

Connect wires from the positive terminal of one module to the

negative terminal of the next module. Figure 1 shows modules

connected in series.

Connect PV modules in parallel to increase current. Connect

wires from the positive terminal of one module to the positive

terminal on the next module. Figure 2 shows modules

7. GROUNDING

The frame grounding must consider the local requirement and

regulation at the installation site. When grounding is required,

please refer to below example connection (Figure 3). Please

be careful in arranging the system ground so that the removal

of one module from the circuit will not interrupt the grounding of

any other modules.

The modules should be grounded to the same electrical point

You can use hole with the appropriate symbol for a

equipotential bonding on the side frame for either a bolt, nut and

washer grounding the module to the frame, a ground lug

fastened by bolt or screw, or appropriate screw (hardware not

provided). An example of acceptable ground connection using

a bolt, nut and washer retaining a ground lug is shown in gure

3. In a connection of this type, the hardware (such as a toothed

locked washer / star washer) must score the frame surface to

make positive electrical contact with the frame. The ground wire

must be considered within the local requirement of local and

regulation at the site of installation.

8. MOUNTING

Please make sure that all the information described in the

installation manual is still valid and proper for your installation.

The mounting method has been veried by SHARP and NOT

CERTIFIED by a third party organization.

Although Sharp does not specify or warrant frame clips or

clamps, using frame clips (not provided) or clamps (not

provided) is possible when they are designed for PV modules

and with minimum dimensions on the sides of the module in

accordance with the instructions and drawings provided. If using

frame clips or clamps, the modules should be xed rigidly and

there shall be no damage to the modules rming by defo

mounting structure against design l oad.

T Sharp module guaranty may be void if customer-selectedhe

frame clips are improper or inadequate for module properties

(including strength or material) or installation. Note that if metal

clips are used, there must be a path to ground from the clips,

(for instance, using star washers in the clip hardware set).

Please review the descriptions and drawings carefully; not

mounting the modules according to one of these methods may

void your guaranty. Support structures that PV modules are

mounted on should be rigid. Sharp PV modules are designed to

ensure optimal electrical performance under the condition that

they are mounted on rigid support structures. Deformation of

support structure may damage PV module with its electric

performance.

When mounting the module on structure, ensure that no corner

has a displacement of more than 2mm per every 1000mm of the

diagonal.

9. MAINTENANCE

The modules are designed for long life and require very little

maintenance. If the angle of the PV module is 5 degrees or more,

normal rainfall is sucient to keep the module glass surface

clean under most weather conditions. If dirt build-up becomes

excessive, use only a soft, damp cloth and water to clean the

glass. If cleaning the back of the module is required, take utmost

care not to damage the back side materials. In order to ensure

the operation of the system, check the connection of wiring and

the state of the jacket of wires occasionally.

For PV modules with anti-reective coating glass, do not touch

the glass since nger prints or stains will easily mark. If dirt build-

up becomes excessive, clean the glass surface with water only.

Bypass Diode

(Built- Junction Box) in

Bypass Diode

(Built- Junction Box) in

Tuotetiedot

Merkki:	Sharp
Kategoria:	Ei luokiteltu
Malli:	NU-AC310

Tarvitsetko apua?

Jos tarvitset apua merkille Sharp NU-AC310 esitä kysymys alla ja muut käyttäjät vastaavat sinulle

Nimesi*

Sähköpostisi*

Kirjoita kysymyksesi tähän

Ei luokiteltu Sharp Käyttöohjeet

Sharp NQ-R256A Käyttöohje

1 Huhtikuuta 2025

Sharp QW-NA1CF47DW-DE Käyttöohje

10 Tammikuuta 2025

Sharp PN-60TW3 Käyttöohje

4 Tammikuuta 2025

Sharp NU-RJ285 Käyttöohje

4 Tammikuuta 2025

Sharp NU-RJ280 Käyttöohje

4 Tammikuuta 2025

Sharp NU-AK310 Käyttöohje

4 Tammikuuta 2025

Sharp NU-AF370 Käyttöohje

4 Tammikuuta 2025

Sharp NQ-R258H Käyttöohje

4 Tammikuuta 2025

Sharp NU-RD300 Käyttöohje

4 Tammikuuta 2025

Sharp NU-AH370 Käyttöohje

4 Tammikuuta 2025

Ei luokiteltu Käyttöohjeet

Viimeisimmät Ei luokiteltu Käyttöohjeet

Daikin EKWCTRDI1V3 Käyttöohje

9 Huhtikuuta 2025

Simplified MFG SP18CAT120 Käyttöohje

9 Huhtikuuta 2025

AudioQuest Pegasus Käyttöohje

9 Huhtikuuta 2025

Reolink P330 Käyttöohje

9 Huhtikuuta 2025

Reolink NVS16-8MB8 Käyttöohje

9 Huhtikuuta 2025

Drive Medical RTL12045 Käyttöohje

9 Huhtikuuta 2025

Kern MBC-A05 Käyttöohje

9 Huhtikuuta 2025

Daikin EKEXVA250 Käyttöohje

9 Huhtikuuta 2025

Apc SurgeArrest Essential PE3WU3 Käyttöohje

9 Huhtikuuta 2025

AudioQuest Yosemite Käyttöohje

9 Huhtikuuta 2025