Sharper Image Fine Facial Hair Remover Käyttöohje

Sharper Image Ei luokiteltu Fine Facial Hair Remover

Lue alta 📖 käyttöohje suomeksi merkille Sharper Image Fine Facial Hair Remover (5 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 2 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/5
Item No. 100871
FINE FACIAL HAIR REMOVER
User Guide
- 1 -
Thank you for choosing the Fine Facial Hair Remover from Sharper Image. Please
read this Quick Start Guide to get a general idea of how this product works. For
additional instructions and important safety information, be sure to read the
entire users manual in the package.
- 2 -
FEATURES
Painless hair removal at home
Safe for all skin tones and all hair types
Cordless and portable
Includes control unit, cotton buds for facial hair and eyebrows
Includes pad set (3 rectangular pad, 2 round pads and 1 upper lip pad) for treating
larger areas
Includes 1 lead with 3 pad connectors
Includes treatment tweezers and curly lead for removing single hairs
Includes conductive gel and carry case
Operates on 2 included AA batteries
IDENTIFICATION OF PARTS
BATTERY INSTALLATION
Install the 2 AA batteries (included) by pressing the battery cap down.
Insert the batteries according to the correct polarity (“+” or “-”).
Replace the cap.
- 3 -
HOW TO USE COTTON BUD TO REMOVE HAIR WITH THE FINE FACIAL
HAIR REMOVER
1. Thoroughly clean treatment area by removing all makeup. The area must
be completely clean, dry and non-greasy.
2. Cut the cotton bud in half and insert into the tip of the device.
3. Dip cotton bud into the conductive gel making sure the gel also covers
the cotton bud holder at the tip of the control unit.
4. Hold the Fine Facial Hair Remover like a pen and slide the switch to the
PROBE position. (Red power light should illuminate to confirm battery is
working). See illustrations on Page 5 for proper holding technique.
5. Put the device on the hair removal area and press the silver activator
button. The green LED light will come on when you’ve made good contact
with the conductive gel, and a buzzer will go off after 20 seconds to
notify you that the treatment is finished.
Note: If you do not touch the gel continuously, the green conductivity
light will go out. Do not exceed one 20-second treatment per day in the
same treatment area (2-cm diameter). Do not exceed a maximum of 3
treatments per week in one treatment area.
Note: To avoid shock do not hold the silver activator button down after the
green conductivity LED light illuminates.
HOW TO USE TREATMENT TWEEZERS WITH THE FINE FACIAL HAIR
REMOVER
1. Thoroughly clean treatment area and remove any makeup. The area
must be completely clean, dry and non-greasy. Cut long hairs as short as
possible with scissors or a razor before use.
2. Plug the Treatment Tweezers into the jack on the end of the Fine Facial
Hair Remover.
3. Apply conductive gel to the target area and to the tweezer tips.
4. Slide the switch to mode.PROBE
5. Select and hold hair to be treated between tweezer tips. When tweezers
are squeezed together the green conductivity LED light will illuminate
and beep.
6. Gently remove hair in the direction of growth on the upper lip and face,
eyebrows or chin using the tweezers.

Tuotetiedot

Merkki: Sharper Image
Kategoria: Ei luokiteltu
Malli: Fine Facial Hair Remover

Tarvitsetko apua?

Jos tarvitset apua merkille Sharper Image Fine Facial Hair Remover esitä kysymys alla ja muut käyttäjät vastaavat sinulle




Ei luokiteltu Sharper Image Käyttöohjeet

Ei luokiteltu Käyttöohjeet

Viimeisimmät Ei luokiteltu Käyttöohjeet