StarTech.com HB31C3A1CME Käyttöohje
StarTech.com
USB-keskitin
HB31C3A1CME
Lue alta 📖 käyttöohje suomeksi merkille StarTech.com HB31C3A1CME (2 sivua) kategoriassa USB-keskitin. Tämä opas oli hyödyllinen 3 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/2
Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: December 2, 2020
Product Diagram (HB31C3A1CME)
Front View
Rear View
Port Function
1USB-C Port
• SuperSpeed USB 10Gbps (USB 3.2 Gen 2)
• Supports USB BC 1.2 charging
• Supports surge and 15KV ESD (Electrostatic
Discharge) protection
• Connect to the USB-C Peripheral Devices Hub
2USB-A Ports (x 3)
• SuperSpeed USB 10Gbps (USB 3.2 Gen 2)
• Used to connect ( x 3) to USB-A Peripheral Devices
the .Hub
• Supports USB BC 1.2 charging
• Supports surge and 15KV ESD (Electrostatic
Discharge) protection
3Mounting Holes • Wall mount the Hub
• Mount the to the side/underside of a Hub Desk
4USB-C Host Port • SuperSpeed USB 10Gbps (USB 3.2 Gen 2)
• Connect the to a Hub Host Computer
52-Wire Terminal Block • Connect an external (+7 - 24V DC DC Power Source
Input) to the Hub
6Power Input Port • Connect a to power the DC 12V Power Source Hub
4-Port Industrial USB-C™ 10Gbps Hub - 3x USB-A + 1 USB-C - ESD + Surge Protection
Package Contents
• USB Hub x 1
• Universal Power Adapter (NA, JP, UK, EU, ANZ) x 1
• Terminal Block Connector x 1
• USB Type-C to Type-C Cable x 1
• USB Type-C to Type-A Cable x 1
• Quick-Start Guide x 1
Requirements
For the latest requirements, please visit:
www.startech.com/HB31C3A1CME.
• Mounting Screws (x 2)
Tools
• Phillips or Flat Head Screwdriver
• Writing Utensil
• Level
Installation
Warning: Connect the after all the other installation steps Universal Power Adapter
have been completed.
Notes: There are two ways to power the . Hub
It is recommended to use an external or a DC Power Source Terminal Block Power
Source (+7 - 24V DC) 2-Wire Terminal Block connected to the to ensure full and
stable function.
Connect the USB Ports
1. Connect a (included) to the on theUSB Type-C to Type-C Cable USB-C Host Port
rear of the and to a on the . Hub USB-C Port Host Computer
2. The should detect the and automatically Host Computer’s Operating System Hub
install it.
3. Connect the to the and the (x3) USB Peripheral Devices USB-C Port USB-A Ports
on the front of the .Hub
Power the Hub
Power the Hub Using the 2-Wire Terminal Block
1. Remove the from the rear of the .Terminal Block Connector Housing Hub’s Casing
12
4 5 63 3
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void
the user’s authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer to .
www.startech.com/warranty
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
Safety Measures
• If product has an exposed circuit board, do not touch the product under power.
Mesures de sécurité
• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.
安全対策
• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。
Misure di sicurezza
• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.
Säkerhetsåtgärder
• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.
FR: fr.startech.com
DE: de.startech.com
ES: es.startech.com
NL: nl.startech.com
IT: it.startech.com
JP: jp.startech.com
StarTech.com Ltd.
45 Artisans Cres
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd,
Brackmills
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
Wall Mounting
Note: It is recommended that are used when wall mounting this . Wall Studs Hub
1. Hold the in the desired mounting location. Hub
2. Mark the location of the , using a . Mounting Holes Writing Utensil
3. Draw a line connecting the two , using a .Mounting Holes Level
4. Hold the in the desired mounting location, aligning the on Hub Mounting Holes
the sides of the with the created in step 2. Hub Mounting Hole Marks
5. Insert the (x 2) through the and into the Mounting Screws Wall Mounting Holes
Wall.
6. Tighten the until the is securely fasten to the , using a Mounting Screws Hub Wall
Phillips Head Screwdriver.
2. Loosen the screws for the on the , using a Terminals Terminal Block Connector
Phillips or Flat Head Screwdriver.
3. Connect the and from the (+7 - 24V DC) to Power Ground Wires DC Power Source
the on the , the are marked on theTerminals Terminal Block Connector Terminals
Hub’s Casing.
Note: Ensure the polarity of the input power is correctly matched with the Terminal
Block Pins to ensure proper function.
Terminal Block Pins
4. Insert the back into the rear of the .Terminal Block Connector Housing Hub
Power the Hub Using the Universal Power Adapter
• Connect the to the on the rear of theUniversal Power Adapter Power Input Port
Hub AC Electrical Outletand to an .
Tuotetiedot
| Merkki: | StarTech.com |
| Kategoria: | USB-keskitin |
| Malli: | HB31C3A1CME |
Tarvitsetko apua?
Jos tarvitset apua merkille StarTech.com HB31C3A1CME esitä kysymys alla ja muut käyttäjät vastaavat sinulle
USB-keskitin StarTech.com Käyttöohjeet
5 Joulukuuta 2024
5 Joulukuuta 2024
5 Joulukuuta 2024
5 Joulukuuta 2024
5 Joulukuuta 2024
5 Joulukuuta 2024
5 Joulukuuta 2024
5 Joulukuuta 2024
5 Joulukuuta 2024
5 Joulukuuta 2024
USB-keskitin Käyttöohjeet
- USB-keskitin Panduit
- USB-keskitin Gembird
- USB-keskitin Digitus
- USB-keskitin Tripp Lite
- USB-keskitin Sitecom
- USB-keskitin Logilink
- USB-keskitin Speed-Link
- USB-keskitin Crestron
- USB-keskitin Manhattan
- USB-keskitin IOPLEE
- USB-keskitin Icy Box
Viimeisimmät USB-keskitin Käyttöohjeet
11 Joulukuuta 2024
10 Joulukuuta 2024
10 Joulukuuta 2024
10 Joulukuuta 2024
4 Joulukuuta 2024
26 Lokakuuta 2024
25 Lokakuuta 2024
25 Lokakuuta 2024
25 Lokakuuta 2024
25 Lokakuuta 2024