StarTech.com ST1030USBM Käyttöohje
StarTech.com
USB-keskitin
ST1030USBM
Lue alta 📖 käyttöohje suomeksi merkille StarTech.com ST1030USBM (4 sivua) kategoriassa USB-keskitin. Tämä opas oli hyödyllinen 3 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/4
Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: September 10, 2024 6:17 PM
Product ID: HB30A10AME, ST1030USBM
Component Function
12-Wire Terminal Block • Used to connect an external DC Power Source
(7~24V DC Input) to the .Hub
2Screw Locks (x 10)
• Used to securely lock a to the USB Device
USB-A Port Hub on the .
• Center to center 19 Screw Lock Dimensions:
mm, thread size 4 - 40.
3Power LED • : Indicates that the Hub is receiving Green
power.
4USB-B Host Port
• Used to connect a to the .Host Computer Hub
• Center to center 24 Screw Lock Dimensions:
mm, thread size 4 - 40.
5USB-A Ports (x 10)
• Used to connect ( x 10) to the USB Devices
Hub.
• Used to charge connected .USB-A Devices
• USB-A Ports support surge and 15KV ESD
(Electrostatic Discharge) Protection.
10-Port Industrial USB 3.0 (5 Gbps) Hub | USB 3.2 Gen 1 to 10x USB-A | ESD & Surge Protection
3
Requirements
For the latest requirements, please visit or
www.startech.com/HB30A10AME www.
startech.com/ST1030USBM
• Phillips Head Screwdriver
• Writing Utensil
• Level
• Mounting Screws (x 2)
Installation
Notes: It is recommended to use an external (+7 - 24V DC)DC Power Source
connected to the to ensure sucient power/current is 2-Wire Terminal Block
delivered to each on the . USB-A Port Hub
Powering the Hub Using the Universal Power Adapter
1. Connect the to the and to a Universal Power Adapter Terminal Block AC
Electrical Outlet.
Note: HB30A10AME ST1030USBMUniversal power adapter included with ; does not
include power adapter ( ).sold separately
2. Connect a (the end will depend on USB Port you are USB-B to USB Cable
connecting to) to the and to a USB port on the .USB-B Host Port Host Computer
3. The should detect the and Host Computer’s Operating System Hub
automatically install it.
4. Connect your to the (x 10) on the . USB Devices USB-A Ports Hub
Powering the Hub Using the 2-Wire Terminal Block
1. Remove the from the .Terminal Block Connector Housing Hub’s Casing
2. Using a small screwdriver (Phillips or Flat Head), loosen the screws on the Terminal
Block Connectors.
3. Connect the and from your (+7 - 24V DC) Power Ground Wires DC Power Source
to the proper , the terminals are marked on theTerminal Block Connectors Hub’s
Casing.
4 5
2
1
* Actual product may vary from photos
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a dierent circuit than the receiver.
- Consult the dealer or an experienced radio/TV technician for help.
Any changes or modications not expressly approved by the party responsible for compliance could void the user’s authority
to operate the device. If shielded interface cables are included with the product, or if additional components or accessories are
designated for use with the installation, they must be used to ensure compliance with FCC regulations..
ISED Statement / Déclaration d’ISDE
CAN ICES-003(B) / NMB-003(B)
This Class B digital apparatus complies with Canadian ICES-003.
This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Le présent appareil est conforme aux CNR d’ISDE Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer to .
www.startech.com/warranty
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
Safety Measures
• If product has an exposed circuit board, do not touch the product under power.
Mesures de sécurité
• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.
安全対策
• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。
Misure di sicurezza
• Se il prodotto p2-ha un circuito stampato visibile, non toccare il prodotto quando è acceso.
Säkerhetsåtgärder
• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com Ltd.
45 Artisans Cres
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd,
Brackmills
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
StarTech.com Ltd.
Siriusdreef 17-27
2132 WT Hoofddorp
The Netherlands
Din Rail Mounting
Wall Mounting
It is recommended that you use when wall mounting the .Wall Studs Hub
1. Align the on the wall in the position you want to mount the .Hub Hub
2. Using a mark o both of the .Writing Utensil Mounting Holes
3. Using a , draw a line connecting the two , making sure that the Level Mounting Holes
line is level.
4. Align the on the with the .Mounting Holes Hub Mounting Hole Marks
5. Insert the (x 2) through the and into the Mounting Screws Wall Mounting Holes
Wall.
6. Using a tighten the until the is Phillips Head Screwdriver Mounting Screws Hub
securely fasten to the .Wall
Note: Ensure the polarity of the input power is correctly matched with the Terminal
Block Pins to ensure proper function.
Terminal Block Pins
4. Insert the onto the . Terminal Block Housing Hub’s Casing
Mounting
DIN Rail Mounting
1. Align the (x 2) with the (x 4) on the back of the Din Rail Brackets Mounting Holes
Hub.
2. Insert the (x 4) through the and into the .Mounting Screws Din Rail Brackets Hub
3. Using a tighten the . Be careful not to Phillips Head Screwdriver Mounting Screws
over-tighten the . Mounting Screws
4. Clip the onto a securing the to the .Din Rail Brackets Din Rail, Hub Din Rail
Tuotetiedot
| Merkki: | StarTech.com |
| Kategoria: | USB-keskitin |
| Malli: | ST1030USBM |
Tarvitsetko apua?
Jos tarvitset apua merkille StarTech.com ST1030USBM esitä kysymys alla ja muut käyttäjät vastaavat sinulle
USB-keskitin StarTech.com Käyttöohjeet
5 Joulukuuta 2024
5 Joulukuuta 2024
5 Joulukuuta 2024
5 Joulukuuta 2024
5 Joulukuuta 2024
5 Joulukuuta 2024
5 Joulukuuta 2024
5 Joulukuuta 2024
5 Joulukuuta 2024
5 Joulukuuta 2024
USB-keskitin Käyttöohjeet
- USB-keskitin Panduit
- USB-keskitin Gembird
- USB-keskitin Digitus
- USB-keskitin Tripp Lite
- USB-keskitin Sitecom
- USB-keskitin Logilink
- USB-keskitin Speed-Link
- USB-keskitin Crestron
- USB-keskitin Manhattan
- USB-keskitin IOPLEE
- USB-keskitin Icy Box
Viimeisimmät USB-keskitin Käyttöohjeet
11 Joulukuuta 2024
10 Joulukuuta 2024
10 Joulukuuta 2024
10 Joulukuuta 2024
4 Joulukuuta 2024
26 Lokakuuta 2024
25 Lokakuuta 2024
25 Lokakuuta 2024
25 Lokakuuta 2024
25 Lokakuuta 2024