V-Tac VT-66 Käyttöohje
Lue alta 📖 käyttöohje suomeksi merkille V-Tac VT-66 (15 sivua) kategoriassa Lamppu. Tämä opas oli hyödyllinen 2 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/15
WEEE Number: 80133970
INSTALLATION INSTRUCTION
LED SOLAR LIGHT
IN CASE OF ANY QUERY/ISSUE WITH THE PRODUCT, PLEASE REACH OUT TO US AT: SUPPORT@V-TAC.EU
FOR MORE PRODUCTS RANGE, INQUIRY PLEASE CONTACT OUR DISTRIBUTOR OR NEAREST DEALERS.
V-TAC EUROPE LTD. BULGARIA, PLOVDIV 4000, BUL.L.KARAVELOW 9B
WARNING!
1. The light source of this luminaire is not replaceable;
when the light source reaches its end of life the whole
luminaire shall be replaced.
2. Installation should be done by certified electrician.
This marking indicates
that this product should
not be disposed of with
other household wastes
MULTI-LANGUAGE
MANUAL QR CODE
Please scan the QR code
to access the manual in
multiple languages.
INTRODUCTION & WARRANTY
Thank you for selecting and buying V-TAC product. V-TAC will serve you the best. Please
read these instructions carefully before starting the installation and keep this manual
handy for future reference. If you have any another query, please contact our dealer or
local vendor from whom you have purchased the product. They are trained and ready
to serve you at the best.The warranty is valid for 3 years from the date of purchase.
The warranty does not apply to damage caused by incorrect installation or abnormal
wear and tear. The company gives no warranty against damage to any surface due to
incorrect removal and installation of the product.
3
YEARS
WARRANTY
*
TECHNICAL SPECIFICATIONS
MODEL VT-66
WATTS 2W
LUMENS 280LM
BEAM ANGLE 120
CRI >80
IP RATING IP65
SOLAR LIGHT
EN
INSTALLATION DIAGRAM
I. Ground installation instructions:
1. After confirming the installation position, fix the
grounding support with screws. As shown in
Figure 1.
2. Install the lamp onto the bracket and tighten
the
screw with a six-legged wrench. As shown in
Figure 2 & 3.
II. Surface mounted installation instructions:
1. Choose the appropriate installation position and
fix the installation bracket with screws. Picture 1.
2. Install the lamp on the mounting bracket and
tighten the screw by hand with a six-legged
wrench.
Switch Function:
- Press and hold the button for 2-3 seconds to
switch ON the solar light. Once switched ON it will
indicate a blue light.
- When switching on the solar light by default it
will be in Mode 1.
- To enter Mode 2, press the button again.
- Pressing the button for the third time the solar
light will switch OFF and the blue light will
disappear.
Operating Modes:
Mode 1: Sensor Mode.
- At dusk, it automatically turns to 10% brightness.
- Turns on to 100% brightness when motion is detected in the range of <5 meters.
- In 30 seconds if no motion is detected the light switches to 10% brightness.
- Turns off at the dawn.
Mode 2: Constant Brightness Mode.
- The sensor will be disabled.
- Automatically turns on at the dusk with 100% brightness and works constantly till the battery
capacity goes to Zero. (Upto 4 hours).
SOLAR LIGHT
EN
STRUCTURE AND SIZE NOTES
1. This production is a solar energy product.
When installing, the solar panels of the
product must be illuminated in the direction
of the sun. If not placed in the direction of
the sun the lamp will not function properly.
Resulting in the lamp to no switch ON or the
light is functions for a short period of time
only. Solar panel should be placed in the
direction of the sunlight. The performance
of the light is the best if the illumination
time of the sun light is longer than 6 hours
resulting in the light to be turned on for its
maximum time.
2. This product is mainly installed on the
wall and is not allowed to be used in damp
or immersed places. Otherwise, it will have
a breakdown and affect its service life.
3. The product can achieve the expected
brightness and light-up time when the
battery is full of electricity. Such as overcast
and rainy days, which will cause insufficient
charging and shorten the light-uptime. If
the lighting time is not long on sunny days,
please check whether the solar panels
are exposed to the sun for a long time. Or
whether the solar panel is dirty and dusty,
ensure to keep the solar panels clean.
4. LED Solar light is designed with a
replaceable battery. It should be replaced
after 3 years of use. After removing the
wire connection from the original lithium
battery, the battery will be removed and
replaced with the new battery of the same
specifications.
1. Solar Panel
11. Column
12. Fixing Base
13. Screw
14. Fixing Bracket
15. Sprike Bracket
2. Fixing frame
4. Fixing base
5. Litihium battery
7. Control panel
8. Switch button
9. LED
10. PC Cover
6. LED and battery
fixing box
3. Waterproof silicone
rubber ring
Tuotetiedot
| Merkki: | V-Tac |
| Kategoria: | Lamppu |
| Malli: | VT-66 |
Tarvitsetko apua?
Jos tarvitset apua merkille V-Tac VT-66 esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Lamppu V-Tac Käyttöohjeet
19 Lokakuuta 2024
18 Lokakuuta 2024
18 Lokakuuta 2024
18 Lokakuuta 2024
18 Lokakuuta 2024
18 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
Lamppu Käyttöohjeet
- Lamppu Ledlenser
- Lamppu Neewer
- Lamppu Topeak
- Lamppu Godox
- Lamppu IKEA
- Lamppu Sony
- Lamppu ET2
- Lamppu Crystorama
- Lamppu EMOS
- Lamppu BeamZ
- Lamppu Maxim
- Lamppu Ansmann
- Lamppu Elation
- Lamppu Fredrick Ramond
- Lamppu Chauvet
- Lamppu Karma
- Lamppu Ridem
- Lamppu Hansa
- Lamppu Casalux
- Lamppu Profoto
- Lamppu Petzl
- Lamppu Gravity
- Lamppu Olight
- Lamppu Kanlux
- Lamppu Xline
- Lamppu ARRI
Viimeisimmät Lamppu Käyttöohjeet
27 Lokakuuta 2024
27 Lokakuuta 2024
27 Lokakuuta 2024
27 Lokakuuta 2024
27 Lokakuuta 2024
27 Lokakuuta 2024
27 Lokakuuta 2024
27 Lokakuuta 2024
27 Lokakuuta 2024
27 Lokakuuta 2024