Watson C-AM-4E Käyttöohje

Lue alta 📖 käyttöohje suomeksi merkille Watson C-AM-4E (4 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 4 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/4
Thank you for choosing Watson Pro
Please read this user manual carefully and keep
it for reference before using the charger.
C-AM-4E
C-VM-4E
Quad Position
Li-ion Battery Charger
TM
SAFETY INSTRUCTIONS
Do not store, place, or use the charger where it may come into contact with
excess heat, water or moisture.
High-voltage internal components present the risk of electrical shock.
Make sure the XLR cable is securely locked into the port before use. You should
hear an audible click.
Charge only on a vibration-free, dry surface at room temperature.
Should you ever notice smoke or a strange odor coming out of the charger,
immediately unplug the AC adapter from the power outlet. Using the charger
under these conditions can cause fire and electric shock.
Do not short-circuit the terminals of your battery or charger.
Do not attempt to disassemble any part of the charger.
Use this charger with Watson Pro batteries only.
The charger, adapters, and batteries may feel warm during the charging process.
This is normal.
Please remove any battery after fully charged.
Unplug the AC cable or 4-pin XLR cable from the power outlet and clean the area
around the prongs of the plug when necessary. The presence of dust around the
prongs can cause fire.
CONNECTING POWER
1. Use the included AC power cable and plug the three pronged end into a properly
grounded AC outlet.
2. Plug the other end of the AC power cable into the WatsonPro battery charger's
AC Input port.
3. Toggle the power switch to the Charger position. The charging status indicators
should turn green when you power on the device.
ATTACHING A BATTERY TO THE CHARGER
To attach a battery to either the 3-Stud or V-Mount interface, follow these steps:
1. Place the charger on a flat surface.
2. Align the 3-Stud Mount (C-AM-4E) or V-Mount (C-VM-4E) on the battery with
the appropriate slots in the charging plate.
3. Slide the battery into place to lock. You should hear a click.
CONNECTING DEVICES
1. Use the included 4-pin XLR cable and plug the male end into the charger s DC out
port until it clicks.
2. Plug the other end of the 4-pin XLR cable into your device. This can be a video
camera or monitor as well as lighting fixture.
3. Toggle the Charger/DC out switch to the DC out position. The DC out indicator
should glow red.
RELEASING THE BATTERY FROM THE CHARGER
1. Press and hold the battery release latch.
2. Slide the battery out from the charger slots, and separate it from the
charging plate.
1. Charging status indicator
1. DC output indicator
1. Battery release latch
1. Charging plates
1. Charge / DC out switch
1. DC output
1. AC input
Included: AC power cable
4-pin XLR cable
CH1 CH3
CH2
DC Out
CH4
LED STATUS
OVERVIEW
Green
Charger is turned on without any batteries connected.
Battery is fully charged.
Red
Battery connected with low or no power.
Battery is charging.
DC output indicator (DC-out is selected).
Flashing red
and green
The charger has detected a defective battery with the
battery. For more information, or to arrange service, visit
www.poweredbywatson.com or call Watson Customer
Service at 212-594-2120.
1 5
1
1
1
1
7
6
5
4
4 4 4 4
3 7
3 3
2 6
2

Tuotetiedot

Merkki: Watson
Kategoria: Ei luokiteltu
Malli: C-AM-4E

Tarvitsetko apua?

Jos tarvitset apua merkille Watson C-AM-4E esitä kysymys alla ja muut käyttäjät vastaavat sinulle




Ei luokiteltu Watson Käyttöohjeet

Watson

Watson VM-98-MI Käyttöohje

21 Joulukuuta 2024
Watson

Watson C-NPF-4B Käyttöohje

21 Joulukuuta 2024
Watson

Watson C-AM-4E Käyttöohje

21 Joulukuuta 2024
Watson

Watson VM-230-SP Käyttöohje

21 Joulukuuta 2024

Ei luokiteltu Käyttöohjeet

Viimeisimmät Ei luokiteltu Käyttöohjeet