Whirlpool AKM 261/IX Käyttöohje
Lue alta 📖 käyttöohje suomeksi merkille Whirlpool AKM 261/IX (6 sivua) kategoriassa Uuni. Tämä opas oli hyödyllinen 2 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/6
IMPORTANT SAFETY INSTRUCTIONS
These instructions shall also be available on website: www.whirlpool.eu
YOUR SAFETY AND THE SAFETY OF OTHERS ARE VERY IMPORTANT
This manual and the appliance itself provide important safety messages, to be read and observed at all times.
This is the safety alert symbol, pertaining to safety, which alerts users to potential hazards to themselves and others.
All safety messages will follow the safety alert symbol and either the terms:
Indicates a hazardous situation which, if not avoided, will cause serious injury.
Indicates a hazardous situation which, if not avoided, could cause serious injury.
All Safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
- The appliance must be disconnected from the power supply before carrying out any installation work.
- Installationandmaintenancemustbecarriedoutbyaqualiedtechnician,incompliancewiththemanufacturer’sinstructionsandlocalsafetyregulations.Donotrepair
orreplaceanypartoftheapplianceunlessspecicallystatedintheusermanual.
If the information in this manual is not followed exactly, a re or explosion may result causing property damage or injury.
- Donotstoreorusegasolineorotherammablevaporsandliquidsinthevicinityofthisappliance.
What to do if you smell gas:
- Do not try to light any appliance.
- Do not touch any electrical switch.
- Do not use any phone in your building.
- Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
- If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency or the gas supplier.
- Use appliance in well ventilated rooms only.
The electrical and gas connections must comply with local regulations.
• When the hob is installed, provide a multi-pole circuit breaker with a contact separation of at least 3 mm, that
provides full disconnection.
• Regulations require that the appliance is grounded.
• Thepowercablemustbelongenoughforconnectingtheappliance,oncettedinitshousing,tothepower
supply.
• Useonlyexibleorrigidmetalhoseforgasconnection.
• Ifnecessary,theelectricalpowercablemustbereplacedexclusivelywithapowercablehavingidentical
characteristicsto theoriginal suppliedby manufacturer.Thisoperation mustbe performedby aqualied
electrician.
• The manufacturer cannot be held responsible for any injury to persons or animals or damage to property
arising from failure to comply with these requirements.
• Donotusemultipleplugadaptersorextensioncords.
• Donotpullthepowercabletodisconnectitfromtheelectricalsupply.
• The electrical components must not be accessible to the user after installation.
• Donottouchtheappliancewithanywetpartofthebodyanddonotoperateitwhenbarefoot.
• Thishob(class3)isdesignedsolelyforprivatehouseholduseforcookingfood.Donotusethisapplianceas
aspaceheatertoheatorwarmtheroom.Doingsomayresultincarbonmonoxidepoisoningandoverheating
of the hob. The Manufacturer declines all responsibility for inappropriate use or incorrect setting of the controls.
• The appliance and its accessible parts become hot during use. Care should be taken to avoid touching
heating elements. Children less than 8 years of age shall be kept away unless continuously supervised. This
appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory
ormentalcapabilitiesorlackofexperienceandknowledgeiftheyhavebeengivensupervisionorinstruction
concerning use of the appliance in a safe way and understand the hazards involved. They shall not play with
the appliance. Cleaning and user maintenance shall not be made by children without supervision.
DANGER
RNINGWA
RNINGWA
400011181339
AE
UA
GR
IT
PT
ES
GB
KZ
RU
EN
BUILT-IN GAS HOB INSTRUCTIONS
• The use of a gas appliance produces heat and humidity in the room. Make sure the room is well-ventilated,
orinstallanextractorhoodwithexhaustduct.
• Domesticanimalsshouldbekeptawayfromtheappliance.
• In case of prolonged use, additional ventilation may be necessary (by opening a window or increasing the
hoodextractionspeed).
• After use, make sure the knobs are in off position and close the main gas supply cock or the gas cylinder valve.
• Overheatedoilsandfatscatchreeasily.Alwaysremainvigilantwhencookingfoodsrichinfat,oiloralcohol
(e.g. rum, cognac, wine).
• Keep the packaging materials out of the reach of children.
• Before cleaning or maintenance wait for hob to cool down.
• Unattendedcookingonahobwithfatoroilcanbedangerousandmayresultinre.NEVERtrytoextinguish
arewithwater,butswitchofftheapplianceandthencoveramee.g.withalidorareblanket.
• Dangerofre:donotstoreitemsonthecookingsurfaces.
SAVE THESE INSTRUCTIONS
INSTALLATION
After unpacking the hob, make sure that it has not been damaged during transport. In the event of problems, contact the dealer or your nearest After-sales Service.
These instructions are only valid for the countries whose symbols is given on the data plate (under the hob).
TECHNICAL INFORMATION FOR THE INSTALLER
• This product can be embedded in a worktop 20 to 50 mm thick.
• If there is no oven beneath the hob, insert a separator panel that has a surface at least equal to the opening in the work surface. This panel, that has
to close completely the cutout in order to avoid any contact with the bottom part of the hob, must be positioned at a maximum distance of 150 mm
below the upper surface of the work surface but, in no case less than 20 mm from the bottom of the hob. In the case that you intend to install an oven
beneath the hob, make sure that it is manufactured by Whirlpool and equipped with a cooling system. The manufacturer declines all liability if another
brand oven is installed beneath the hob.
• Before installation, make sure that:
- the local gas delivery conditions (nature and pressure) are compatible with the settings of the hob (see the rating plate and injector table);
- the outer surfaces of the furniture or appliances adjacent to the hob are heat resistant according to local regulations;
- thisapplianceisnotconnectedtoafumeexhaustdevice.Itshallbeinstalledinaccordancewithcurrentinstallationregulations.Particularattentionshallbegiven
to the relevant requirements regarding ventilation.
- combustionproductsaredischargedoutdoorsthroughspecichoodsorwalland/orwindowmountedelectricalfans.
GAS CONNECTION
This operation must be performed by a qualied technician.
• The gas supply system must comply with local regulations.
• Youcanndspeciclocalregulationsforsomecountriesintheparagraph“ReferencetoLocalRegulations”.Ifno
information concerning your Country is given, please ask details to your Installer.
• The connection of the hob to the gas pipe network or gas cylinder must be made by means of a rigid copper or
steelpipewithttingscomplyingwithlocalregulations,orbymeansofacontinuous-surfacestainlesssteelhose
complying with local regulations. Interpose gasket (B)intheelbowconnection.Themaximumlengthofthehoseis2m.
• FOR BELGIUM ONLY: It is necessary to replace the elbow connection (A) on the appliance, with the one supplied
(if present).
IMPORTANT: if a stainless steel hose is used, it must be installed so as not to touch any mobile part of the furniture. It must pass through an area where
there are no obstructions and where it is possible to inspect it on all its length.
• Afterconnectiontothegassupply,checkforleakswithsoapywater.Lightuptheburnersandturntheknobsfrommaxposition to minimum position to check
amestability.
ELECTRICAL CONNECTION.
This operation must be performed by a qualied technician.
• The electrical connections must comply with local regulations.
• The earthing of this appliance is compulsory by law.
• Do not use an extension cord.
IMPORTANT: the data relevant to the voltage and power absorption are indicated on the rating plate.
RNINGWA
L
Earth
(yellow/green)
N
EAVERTIZAR
EAVERTIZAR
ASSEMBLY
After having cleaned the perimeter surface, apply the supplied gasket to the hob as shown in the gure.
PositionthehobintheworktopopeningmaderespectingthedimensionsindicatedintheInstruction.
NOTE: the power supply cable must be long enough to permit its upward extraction.
To secure the hob, use the brackets (A) provided with it. Fit the brackets into the relevant bores shown by the arrow and fasten them by means of their screws in accordance
withthethicknessoftheworktop(seethefollowinggures).
Top 20 mm
Top 30-50 mm
ADJUSTMENT TO DIFFERENT TYPES OF GAS
This operation must be performed by a qualied technician.
If the appliance is intended to operate with a different gas from the gas type stated on the rating plate and information label on the top of the hob, change the injectors.
Remove the information label and keep it with the instructions booklet.
Use pressure regulators suitable for the gas pressure indicated in the Instruction.
• ThegasnozzlesmustbechangedbyAfterSalesServiceoraqualiedtechnician.
• NozzlesnotsuppliedwiththeappliancemustbeorderedfromAfterSalesService.
• Adjust the minimum setting of the taps.
NOTE: when liquid petroleum gas is used (G30/G31), the minimum gas setting screw must be tightened as far as it will go.
IMPORTANT: should you experience difculty in turning the burners knobs, please contact the After Sales Service for the replacement of the burner tap
if found to be faulty.
REPLACING THE INJECTORS (see the injector table in the Instruction)
• ).Remove grids (A
• ).Extractburners(B
• Using a socket spanner of the appropriate size unscrew the injector ( ), unscrew the injector to C
be replaced.
• Replace it with the injector suitable for the new type of gas.
• ).Re-assemble the injector in (D
• ). If you have a multiple crown burner use side spanner to replace the injector (E
Beforeinstallingthehob,remembertoafxthegascalibrationplatesuppliedwiththeinjectorsin
suchawaythatitcoverstheexistinginformationrelatingtogascalibration.
ADJUSTING MINIMUM GAS SETTING OF TAPS
To ensure that the minimum setting is correctly adjusted, remove the knob and proceed as follows:
• tightenscrewtoreducetheameheight(-);
• loosenscrewtoincreasetheameheight(+)
Theadjustmentmustbeperformedwiththetapinminimumgassettingposition(smallame) .
• The primary air of the burners does not need to be adjusted.
• Atthisstage,lightuptheburnersandturntheknobsfrommaxposition to minimum position tocheckamestability.
Uponcompletionofadjustment,resealusingsealingwaxoranequivalentmaterial.
REFERENCE TO LOCAL REGULATIONS
GB
Provision for ventilation
The room in which the appliance is installed must have an air supply to current standards. B.S. 5440 - Part 2
All rooms require a permanent vent in addition to the openable window.
If there are other fuel burning appliances in the same room should be consulted to determine the air vent requirements.B.S. 5440 - Part 2
If the appliance is installed in a cellar or basement, it is advisable to provide an air vent of 65 cm, irrespective of the room volume.
RNINGWA
Tuotetiedot
Merkki: | Whirlpool |
Kategoria: | Uuni |
Malli: | AKM 261/IX |
Tarvitsetko apua?
Jos tarvitset apua merkille Whirlpool AKM 261/IX esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Uuni Whirlpool Käyttöohjeet
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
Uuni Käyttöohjeet
- Uuni Teka
- Uuni Miele
- Uuni Etna
- Uuni Haier
- Uuni KitchenAid
- Uuni Insignia
- Uuni LG
- Uuni Bosch
- Uuni BEKO
- Uuni Grundig
- Uuni Hisense
- Uuni Electrolux
- Uuni Café
- Uuni Balay
- Uuni Siemens
- Uuni Arcelik
- Uuni Bartscher
- Uuni Smeg
- Uuni Hoover
- Uuni Thermex
- Uuni Amica
- Uuni IKEA
- Uuni AEG
- Uuni Rosieres
- Uuni Artusi
- Uuni Samsung
- Uuni Neff
- Uuni Delonghi
- Uuni Imarflex
- Uuni Kogan
- Uuni PKM
- Uuni Franke
- Uuni Sauber
- Uuni Candy
- Uuni CDA
- Uuni Gorenje
- Uuni Summit
- Uuni Gemini
- Uuni Monogram
- Uuni Vox
- Uuni Sencor
- Uuni Kluge
- Uuni Bertazzoni
- Uuni DCG
- Uuni Khind
- Uuni Turbotronic
- Uuni Euromaid
- Uuni Hendi
- Uuni Concept
- Uuni Omega
- Uuni Fulgor Milano
- Uuni Hyundai
- Uuni Blaupunkt
- Uuni MSR
- Uuni Salton
- Uuni Cylinda
- Uuni La Cornue
- Uuni Eldom
- Uuni Fisher And Paykel
- Uuni Elba
- Uuni Jenn-Air
- Uuni HomeCraft
- Uuni Jata
- Uuni Signature
- Uuni Freggia
- Uuni Becken
- Uuni Element
- Uuni Glem Gas
- Uuni Hansa
- Uuni Rommelsbacher
- Uuni Mx Onda
- Uuni Meireles
- Uuni Edesa
- Uuni Ronco
- Uuni Gaggenau
- Uuni Mellerware
- Uuni Tisira
- Uuni Wolf
- Uuni Porter & Charles
- Uuni LERAN
- Uuni Zerowatt
- Uuni Baumatic
- Uuni Iberna
- Uuni Ilve
- Uuni Wolkenstein
- Uuni Traeger
- Uuni Atosa
- Uuni Izzy
- Uuni Mora
- Uuni Zenith
- Uuni Rangemaster
- Uuni Lofra
- Uuni Mayer
- Uuni Pitsos
- Uuni Chef
- Uuni Emerio
- Uuni Yamazen
- Uuni ZLine
Viimeisimmät Uuni Käyttöohjeet
27 Lokakuuta 2024
27 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024