Whirlpool FFT CM11 8B Käyttöohje
Whirlpool
Kuivausrumpu
FFT CM11 8B
Lue alta 📖 käyttöohje suomeksi merkille Whirlpool FFT CM11 8B (4 sivua) kategoriassa Kuivausrumpu. Tämä opas oli hyödyllinen 3 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/4
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.
In order to receive a more complete assistance, please
register your product on www.whirlpool.eu/register
EN
Quick guide
Before using the appliance carefully read the Safety
Instructions.
OPENING OF THE DOOR DURING THE CYCLE
Laundry can be checked while the drying cycle runs and any
garments already dry can be removed, while drying continues for
the remaining items. After closing the door, press the "Start/Pause"
button to resume machine operation.
Keep the door closed until the cycle end to save time and energy.
DAILY USE
Doing this will keep your machine working at its BEST:
- remember to empty your water tank after each drying cycle.
- remember to clean your lters after each drying cycle.
Refer to the Care & Maintenance section.
1. Plug the dryer into the power supply socket.
2. Open the door and load garments; always refer to instructions on
clothing labels and the max loads indicated in the programme
section. Empty pockets. Make sure garments do not get caught
between the door and/or the door lter. Do not load items that
are dripping wet. Do not tumble dry large, very bulky items.
3. Close the door.
4. Press the "On/O" button.
5. Select the most suitable programme
for the type of fabric in that
load.
6. Select the options, if necessary.
7. Press the "
Start/Pause"
button to begin drying.
8. At the end of the drying cycle, a buzzer will beep. An indicator on
the control panel signals the end of the cycle. Pull the load out
immediately to prevent the formation of creases on laundry.
9. Turn the machine o by pressing the "On/O" button, open the
door and pull the clothing out. If the machine is not switched o
manually, after about a quarter of an hour from the end of the
cycle , the appliance turns o automatically to save energy.
Note that some programme/option accords with "Crease Care"
system. This means that for some hours, after the end of the
drying cycle, the drum rotates at regular intervals to prevent the
formation of creases.
In case of power failure, it is necessary to press the "Start/Pause"
button to restart the cycle.
CARE LABEL
Always check the care labels, especially when placing garments in
the tumble dryer for the rst time. Below are the most commonly
used symbols:
May be tumble dried.
Do not tumble dry.
Tumble dry – high heat.
Tumble dry – low heat.
FIRST TIME USE
Make sure that the water tank is correctly inserted. Make sure
that the drain hose on the back of the dryer is xed correctly,
either to the dryer’s water tank, or to your domestic drainage
system.
CONTROL PANEL
1 ON/OFF button (Reset if long pressed)
2 Programme selection Knob
3 Start/Pause
Options buttons*
4 Dryness level
5 Start delay
6 Timed drying
7 Cycle end
8 Rapid (Key lock if long pressed)
9 FreshCare+ (Mute if long pressed)
*Note: some models may have the wording in full instead of the icons.
INDICATORS
Dryness level: Iron dry - Hanger dry - Cupboard dry - Extra dry
Cycle phase: Drying - Cool down - End of cycle.
Empty water tank - Clean door lter - Clean bottom lter -
Refer to troubleshooting section: Failure: Call after sales service
DEMO
Demo mode
1
3
2
9
7
8
4 5 6
h
3’’
3’’
These buttons allow you to personalise the selected programme
according to personal requirements. Not all options are available
for all programmes. Some options may be incompatible with
ones you have previously set; if so, you will be alerted by the
buzzer and/or blinking indicators. If the option is available, the
option indicator will stay on. The programme may retain some
options selected in previous drying cycles.
PROGRAMS
Eco kg Max*
This is the most ecient programme in terms of energy
consumption and is suitable for drying normal wet cotton
laundry. The values on the Energy Label are based on this
programme.
NOTE: For optimal energy eciency this cycle by default is set up to
"Cupboard Dry" level. For a higher dryness level we suggest using
the Cotton cycle.
Cotton kg Max*
Cycle suitable for drying all types of cotton, ready to be
placed in the cupboard.
Mixed kg 4
This programme is ideal for drying cotton and synthetic
fabrics together.
Bed linen kg Max*
This programme is intended for drying cotton sheets.
Duvet
Programme intended to dry bulky items, such as a single duvet.
Shirts kg 3
This is a programme for Shirts made from cotton or cotton
blend/synthetics.
Jeans kg 3
For drying sturdy cotton including denim trousers and
jackets.
Easy ironing
This cycle relaxes bres, thus making ironing and folding
easier. Suitable for small load of damp or dry cotton and cotton
blend fabrics. Not for wet items.
Refresh
A short programme suitable for refreshing bres and
garments through the emission of fresh air. Do not use on wet
items. It can be used on with any load size but is more eective
with small loads. It lasts about 20 minutes.
Rapid 30' kg 0,5
Ideal for drying cotton garments spun at high speed in the
washing machine.
Sport kg 4
For drying synthetics or cotton sports garments.
Silk kg 0,5
Gentle drying of silk garments.
Wool kg 1
Programme for drying wool clothes. It is advisable to turn the
items inside out before drying. If heavy edges remain damp, leave
them to dry naturally.
Delicates kg 2
For drying delicate laundry requiring gentle treatment.
Synthetics kg 4
For drying synthetic fabrics.
OPTIONS
Dryness level
Press the related button several times to obtain a dierent
level of residual moisture on garments. An indicator signals the
level being selected.
Iron dry: very delicate drying. Items will be more easily
ironed immediately after the cycle.
Hanger dry: a level intended for delicate garments ready
to be hanged.
Cupboard dry: the laundry is ready to be folded and put
away.
Extra dry: for laundry intended to be worn at the end of the
cycle.
Timed drying
This option is to manually set the drying time. Press the
corresponding button to set the required time for drying. An
indicator on the control panel signals the time being selected.
h
Start delay
This option is for delaying the start of the cycle. Press the
corresponding button several times to nd the required delay. Once
the max time is reached, the option is reset by pressing the button
again. An indicator on the control panel signals the time being
selected. After pressing the "Start/Pause" button, the machine signals
the time remaining to the start of the cycle. If the door is opened,
press the "Start/Pause" button once the door has been closed.
Rapid
Enables quicker drying.
FreshCare+
If laundry is left inside of the drum once the cycle has
ended, it can be subjected to bacterial proliferation. This
option helps to prevent this from happening by controlling the
temperature and gently rotating the drum. This will continue for
up to 6 hours after the end of the cycle. This setting will remain in
the memory of the previous cycle. If this is used alongside Start
Delay, a crease treatment will be perfomed during this phase by
periodic rotations of the drum.
Key lock
This option makes all machine controls inaccesible, except
the "On/O" button. When the machine is on:
• to activate the option, keep the button pressed until the
machines signals that the option has been enabled.
• to disable the option, keep the button pressed until the machine
signals that the option has been disabled.
This option remains in memory if selected in previous drying.
Cycle end
This option activates a prolonged buzzer at the end of the
cycle. Enable it if you are not sure to hear the normal sound at the
end of the cycle. This option remains in memory if selected in the
previous drying.
Mute
This option turns o all sounds of control panel. Only
warnings remain active.
• to activate the option, keep the button pressed until the
indicator goes on.
• to disable the option, keep the button pressed until the indicator
goes o.
The duration of these programs will depend on the size of the
load, types of textiles, the spin speed used in your washer and
any extra options selected. In machines equipped with display,
the duration of the cycles is shown on the control panel. The
remaining time is constantly checked and adjusted during the
drying cycle to show the best possible estimate.
Option to use - If all your loads on Automatic Cycles are
consistently less dry or more dry than you would like, you may
increase or decrease the dryness level using the specic option.
*MAX LOAD 8 Kg (Dry load)
EN
Quick guide
Power consumption
o-mode (Po) - Watts 0.50
left-on mode (Pl) - Watts 1.00
Programs MinutesKg kWh
Eco Cotton * 8 4.74 130
Eco Cotton 4 2.59 80
Synthetics 4 1.84 90
*This is the reference programme for the energy label and suitable to
dry normal wet cotton laundry. This is the most ecient programme
in terms of energy consumption for drying wet cotton laundry.
(Standard/Default starting conguration).
Cleaning the tumble dryer
• The external metal, plastic and rubber parts can be cleaned
with a damp cloth.
• Clean the front air intake grille regularly (every 6 months) with
a vacuum cleaner to remove any lint, u or dust deposits.
Furthermore, remove any lint deposits from the lters area,
using a vacuum cleaner every so often.
• Do not use solvents or abrasives.
CARE AND MAINTENANCE
WARNI NG: unplug the dryer during the cleaning and
maintenance procedures.
Emptying the water tank after each cycle (see Fig. A).
Pull the container out of the dryer and empty it into a sink or other
suitable drain, then place it back properly. Do not use the dryer
without having inserted the container back in place.
Cleaning the door lter after each cycle (see Fig. B).
Pull the lter out and clean it by removing the lint from the lter
surface under running water or using a vacuum cleaner. For optimal
performance, dry up the lter before inserting it back in place.
Do not use the dryer without having reinserted the lter in place.
Remove the door lter as described below:
1. Open the door and pull the lter upwards.
2. Open the lter and remove the lint from all its parts. Replace the
lter correctly making sure it is fully seated.
Cleaning the bottom lter when the relevant indicator
turns on (see Fig. C).
Pull the lter out and remove the lint from its surface by washing
it under runing water or by using a vacuum cleaner.
However, it is advisable to clean this lter after each cycle to
optimise drying performance.
Do not use the dryer without having reinserted the lter in place.
Remove the bottom lter and the condenser as described
below:
1. Open the bottom cover.
2. Take the handle and pull the lter out.
3. Open the rear side of the lter and remove the lint from the
inner surface of the mesh.
4. Clean the lter chamber (there might be residual water: this is
normal).
5. Approximately every 3 months, clean the condensing unit
(gure D) situated behind the bottom lter.
• Lower the levers situated on the sides of the condenser.
Pull the handle to remove the condenser and clean it under
running water.
• Put the the condenser back in place and lift the levers.
6. Close the rear side of the lter and place it back by checking it
is perfectly integrated in place.
7. Lower the lter handle and close the bottom cover.
8. Make sure the air intake is free.
PRODUCT DESCRIPTION
1. Water Tank
2. Air Intake
3. Bottom lter and condenser
4. Door lter
The lters are essential parts for drying. They are intended
to collect the lint formed during drying process. In case
of clogged lters, the air ow inside the dryer would be
seriously aected: the drying times would be longer, the
energy consumption would increase and the dryer could be
damaged. If these procedures are not carried out properly,
the dryer may not start.
A B
1
42
3
C D
TRANSPORT AND HANDLING
Never lift the dryer by holding it at the worktop.
1. Unplug the dryer.
2. Remove the water from the water tank completely.
3. Make sure that door and water tank are properly closed.
4. If the drain hose is connected to your drainage system,
re-connect it to the back of the dryer (see "Installation" section
in the Safety Instruction guide).
Tuotetiedot
| Merkki: | Whirlpool |
| Kategoria: | Kuivausrumpu |
| Malli: | FFT CM11 8B |
Tarvitsetko apua?
Jos tarvitset apua merkille Whirlpool FFT CM11 8B esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Kuivausrumpu Whirlpool Käyttöohjeet
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
Kuivausrumpu Käyttöohjeet
- Kuivausrumpu Maytag
- Kuivausrumpu Haier
- Kuivausrumpu Bosch
- Kuivausrumpu BEKO
- Kuivausrumpu Grundig
- Kuivausrumpu Electrolux
- Kuivausrumpu Siemens
- Kuivausrumpu Arcelik
- Kuivausrumpu Smeg
- Kuivausrumpu Hoover
- Kuivausrumpu AEG
- Kuivausrumpu Kogan
- Kuivausrumpu Candy
- Kuivausrumpu Gemini
- Kuivausrumpu Panasonic
- Kuivausrumpu Hyundai
- Kuivausrumpu Ufesa
- Kuivausrumpu Blaupunkt
- Kuivausrumpu Eldom
- Kuivausrumpu Philco
- Kuivausrumpu Becken
- Kuivausrumpu Heinner
- Kuivausrumpu Gaggenau
- Kuivausrumpu Zerowatt
- Kuivausrumpu Otsein-Hoover
- Kuivausrumpu Baumatic
- Kuivausrumpu Iberna
- Kuivausrumpu KDK
Viimeisimmät Kuivausrumpu Käyttöohjeet
26 Lokakuuta 2024
25 Lokakuuta 2024
25 Lokakuuta 2024
24 Lokakuuta 2024
24 Lokakuuta 2024
24 Lokakuuta 2024
24 Lokakuuta 2024
24 Lokakuuta 2024
24 Lokakuuta 2024
24 Lokakuuta 2024