Whirlpool FFT D 8X3B EE Käyttöohje
Whirlpool
Kuivausrumpu
FFT D 8X3B EE
Lue alta 📖 käyttöohje suomeksi merkille Whirlpool FFT D 8X3B EE (24 sivua) kategoriassa Kuivausrumpu. Tämä opas oli hyödyllinen 3 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/24
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.
In order to receive a more complete assistance,
please register your product on
www.whirlpool.eu/register
EN
PLEASE SCAN THE QR CODE ON YOUR APPLIANCE IN ORDER TO REACH MORE INFORMATION.
Quick guide
Before using the appliance carefully
read the Safety Instruction.
Eco Monitor
This indicator shows the energy consumption level according to
the programme and the options set. The consumption is
proportional to the lines on the display,by the ecomonitor icon.
DAILY USE
Doing this will keep your machine working at its BEST:
- remember to empty your water tank after each drying
cycle.
- remember to clean your lters after each drying cycle.
Refer to the Care & Maintenance section.
1. Plug the dryer into the power supply socket.
2. Open the door and load garments; always refer to instructions on
clothing labels and the max loads indicated in the programme
section. Empty pockets. Make sure garments do not get caught
between the door and/or the door lter. Do not load items that
are dripping wet. Do not tumble dry large, very bulky items. For
optimal drying result, garments should be loaded one by one.
3. Close the door.
4. Press the "On/O" button.
5. Select the most suitable programme
for the type of fabric in
that load.
6. Select the options, if necessary.
7. Press the "
Start/Pause"
button to begin drying.
8. At the end of the drying cycle, a buzzer will beep. An indicator on
the control panel signals the end of the cycle. Turn the machine
o by pressing the "On/O" button, open the door and pull the
clothing immediately out to prevent the formation of creases on
laundry.
If the machine is not switched o manually, after about a quarter
of an hour from the end of the cycle , the appliance turns o
automatically to save energy.
Note that some models perform a nal cool tumble phase, for this
reason the fabrics may not feel hot.
In case of power failure, it is necessary to press the "Start/Pause"
button to restart the cycle.
CARE LABEL
Always check the care labels, especially when placing garments in
the tumble dryer for the rst time. Below are the most commonly
used symbols:
May be tumble dried.
Do not tumble dry.
Tumble dry – high heat.
Tumble dry – low heat.
NAVIGATION
The " " and " " buttons serve to navigate the available UP DOWN
menus.
• Press the button to conrm the selection.
• Press the option button at the symbol , where present on the
display, to return to the previous screen.
If no selection is conrmed, after about 10 seconds, the display
return to the main screen.
SETTINGS
To access the settings menu, keep the relevant button pressed for
some seconds.
• Set language shows the available languages on the display.
• Sounds allows to enable or disable the sounds (some sounds, as
warnings, will remain active anyway).
• Brightness allows to modify the display brightness.
• Factory Default allows to reset the default settings. After having
selected the setting, keep the button pressed for some
seconds.
Opening the door during the cycle
The tumble dryer door can be opened at any time during the cycle
to check progress and remove any garments already dry.
However, since opening the door can extend the drying time, the
recommendation is to keep the door closed throughout the cycle
process to save time and energy.
After closing the door, press the "Start/Pause" button within 15
minutes to resume the machine operation.
INDICATORS
Dryness level: Iron dry - Hanger dry - Cupboard dry - Extra dry
Cycle phase: Drying - Cool down - End of cycle.
Empty water tank - Clean door lter - Clean bottom lter - Eco Monitor
Refer to troubleshooting section: Failure: Call after sales service
FIRST TIME USE
When starting the appliance for the rst time, the control panel
will show the set language menu automatically. The UP and
DOWN buttons serve to show the languages available in the
machine. Press the button to conrm. The machine cannot
be used without having selected the language. Make sure that
the water tank is correctly inserted. Make sure that the drain
hose on the back of the dryer is xed correctly, either to the
dryer’s water tank, or to your domestic sewage system.
The dryer must be installed in ambient with a temperature
range between 5-35 °C to ensure its operation.
Before you use your dryer ensure that it has been in a upright
position for at least 6 hours.
CONTROL PANEL
1 On/O button
2 Start/Pause button
Options Buttons
3 FreshCare+
4 Rapid (Add Favourite if long pressed)
5 Cycle Options (Setting if long pressed)
6 Dryness Level
7 Timed Drying
8 Start Delay
Navigation buttons and Key Lock
9 UP
10 DOWN'
11 CONFIRM (Key Lock if long pressed)
3
4
5
9
10
11
SYNTHETICS
1:35
-:-- -:--
6 7 8
1
2
PROGRAMS
The duration of these programs will depend on the size of the
load, types of textiles, the spin speed used in your washer and
any extra options selected. In machines equipped with display,
the duration of the cycles is shown on the control panel. The
remaining time is constantly checked and adjusted during the
drying cycle to show the best possible estimate.
Option to use - If all your loads on Automatic Cycles are
consistently less dry or more dry than you would like, you may
increase or decrease the dryness level using the specic option.
Eco kg Max*
This is the most ecient programme in terms of energy
consumption and is suitable for drying normal wet cotton
laundry. The values on the Energy Label are based on this
programme.
NOTE: For optimal energy eciency this cycle by default is set up to
"Cupboard Dry" level. For a higher dryness level we suggest using
the Cotton cycle.
Cotton kg Max* '
Cycle suitable for drying all types of cotton, ready to be placed
in the cupboard.
Mixed kg 4
This programme is ideal for drying cotton and synthetic
fabrics together.
Bed Linen kg Max*
This programme is intended for drying cotton sheets.
Duvet
Programme intended to dry bulky garments, as single duvet.
Shirts kg 3
This is a programme for Shirts made from cotton or cotton
blend/synthetics.
Easy Ironing
This cycle allows to extend the bres of garments thus
making ironing and folding easier. Do not use in case of garments
that are still wet. Suitable for small loads of cotton textiles or
cotton blends.
Refresh
A short programme suitable for refreshing bres and
garments by means of fresh air. Do not use with garments that are
still wet. It can be used on with any load size but is more eective
with small loads. The cycle duration is about 20 minutes.
Rapid 30' kg 0.5
Ideal for drying cotton garments spun at high speed in the
washing machine.
Sport kg 4
For drying sports garments made of synthetics or cotton.
Specials
This position allows to select among the various special
programmes. The UP/DOWN buttons serve to scroll the
programmes. Press the button to conrm the selected
programme.
• Jeans kg 3
For drying cotton jeans-wear and garments made of robust
cotton, like denim, such as trousers and jackets.
• Towel kg Max*
For drying robust laundry made of cotton, such as terry
towels.
• Tecnhical Wear kg 4
For drying technical wear made of synthetics or cotton.
• Down Jacket kg 2.5
To dry down jackets, giving their natural softness back
(2 jackets).
Favourite
This position allows to select among programmes and
corresponding options previously saved. The buttons UP/DOWN
allow to scroll the list of saved favourites. Press the button to
select and save the cycle. Use the relevant option to save the
programmes.
Wool kg 1
Programme for drying wool clothing. It is advisable to turn the
garments inside out before drying. Leave to dry naturally the
heaviest edges that are still damp.
Delicates kg 2
For drying delicate laundry which needs gentle treatment.
Synthetics kg 4
For drying laundry made of synthetic bres.
*MAX LOAD 8 Kg (Dry load)
OPTIONS
These buttons allow you to personalise the selected programme
according to personal requirements. Not all options are available
for all programmes. Some options may be incompatible with
ones you have previously set; if so, you will be alerted by the
buzzer and/or blinking indicators. If the option is available, the
option indicator will stay on. The programme may retain some
options selected in previous drying cycles.
Dryness Level
Press the relevant button several times to obtain a dierent
level of residual moisture on garments. The display will signal the
level being selected. After few seconds of inactivity, the display
returns to the main menu.
Iron Dry: a very delicate ironing. Suitable for making ironing
of garments easier immediately after the end of the cycle.
Hanger Dry: a level intended for delicate garments ready to
be hanged.
Cupboard Dry: the garments are ready to be folded and put
away.
Extra Dry: used for garments to be worn at the end of the
cycle.
Timed drying
This option allows to set the drying time. Press the
corresponding button to set the required time for drying. An
indicator on the control panel signals the time being selected.
h
Start Delay
This option allows you to set the delay of the cycle start. Press
the corresponding button several times to obtain the required
delay. After having reached the max. settable time, the option is
reset by pressing the button again. An indicator on the control
panel signals the time being selected. After having pressed the
button Start/Pause, the machine signals the remaining time for the
cycle start. In case of door opening, after closing, it is necessary to
press the button Start/Pause.
FreshCare+
If garments are left inside the drum after the end of the
cycle, they are subject to bacterial proliferation. This option allows
to prevent this proliferation by controlling the temperature and
the rotation of the drum. This treatment has a max. duration of 6
hours after the end of the programme set. This option remains
in memory if selected in the previous drying. If this option is
used together with the Start Delay, a crease treatment (a periodic
rotation of the drum) is added in the Start Delay phase.
Rapid
Enables quicker drying.
Add Favourite
This button allows to add the most used programmes (max.
6 - by entering the seventh one, one of the already saved
programmes will be cancelled) to “Favourite”, already inclusive of
options.
• Select the programme and the options to be saved.
• Keep the button pressed for some seconds.
• Saving is conrmed with a message on the display.
• The same programme cannot be saved twice with dierent
options.
Key Lock
This option makes all machine controls inaccessible, except the
button On/O. When the machine is on:
• to activate the option, keep the button pressed until the
machines signals that the option has been enabled.
• To disable the option, keep the button pressed until the machine
signals that the option has been disabled.
This option remains in memory if selected in the previous drying.
Cycle Option
This buttons serves to access a menu of available options (see
next options). The buttons “UP” and “DOWN” serve to scroll the
options and the button allows to conrm the selection.
EN
Quick guide
• Cycle End Signal
This option activates a prolonged buzzer at the end of the
cycle. Enable it if you are not sure to hear the normal sound at the
end of the cycle.
After having pressed the option button, it can be enabled or
disabled using the and buttons. Press the button UP DOWN to
conrm.
This option remains in memory, if selected in the previous drying.
• Gentle
Enables a more gentle treatment of the laundry by
reducing the drying temperature.
• Anti Tangle
This option has the drum movement modied to give a
tumbling action that reduces tangling and knotting of your clothes.
This option gives best results when used with smaller loads.
Heat Pump System
The heat pump contains uorinated greenhouse gases,
contained in a hermetically sealed unit. This sealed unit contains
0.43 kg of the R134a gas. GWP = 1430 (1 t CO2).
Power consumption
o-mode (Po) - Watts 0.50
left-on mode (Pl) - Watts 2.00
Programs MinutesKg kWh
Eco * 8 1.42 165
Eco 4 0.78 96
Synthetics 4 0.94 113
*This is the reference programme for the energy label and suitable to
dry normal wet cotton laundry. This is the most ecient programme
in terms of energy consumption for drying wet cotton laundry.
(Standard/Default starting conguration).
Cleaning the tumble dryer
• The external metal, plastic and rubber parts can be cleaned
with a damp cloth.
• Clean the front air intake grille regularly (every 6 months) with
a vacuum cleaner to remove any lint, u or dust deposits.
Furthermore, remove any lint deposits from the lters area,
using a vacuum cleaner every so often.
• Do not use solvents or abrasives.
CARE AND MAINTENANCE
WARNING: unplug the dryer during the cleaning and
maintenance procedures.
Emptying the water tank after each cycle (see Fig. A).
Pull the container out of the dryer and and empty it into a
sink or other suitable drain, then place it back. Do not use the dryer
without having inserted the container back in place.
Cleaning the door lter after each cycle (see Fig. B).
Pull the lter out and clean it by removing the lint from the
lter surface under running water or using a vacuum cleaner. For
optimal performance, dry up all the lters before inserting them
back in place. Do not use the dryer without having reinserted
the lter in place.
Remove the door lter as described below:
1. Open the door and pull upwards.
2. Open the lter and remove lint from all its parts. Replace it
correctly.
Ensure it is completely inserted ush with the dryer seal.
Cleaning the bottom lter when the relevant indicator
turns on (see Fig. C).
Pull the lter out and remove the lint from its surface by washing
it under runing water or by using a vacuum cleaner.
However, it is advisable to clean this lter after each cycle to
optimise drying performance.
Do not use the dryer without having reinserted the lter in place.
Remove the bottom lter as described below:
C1. Open the bottom cover; take the handle and pull the lter out.
C2. Open the rear side of the lter and remove the lint from the
inner surface of the mesh.
C3/C4. Check the bottom lter chamber every month. If you
see residual lint accumulated on the metal ns, clean it with a
vacuum cleaner, using a nozzle with a brush.
It's crucial to do vertical movements, you may destroy the
component if you try to clean it in horizontal direction. Avoid the
direct contact of the hand with the ns - risk of cut.
C5. Close the rear side of the lter and place it back by checking it
is perfectly integrated into its seat, then lower the lter handle.
C6. Close the bottom cover.
Make sure the air intake is free.
The lters are essential parts for drying. They are intended
to collect the lint formed during the drying process. In case
of clogged lters, the air ow inside the dryer would be
seriously aected: the drying times would be longer, the
energy consumption would increase and the dryer could be
damaged. If these procedures are not carried out properly,
the dryer may not start.
NOTE: After cleaning the lters the relevant indicator remains on;
this is normal, it will disappear when you start a new drying cycle.
PRODUCT DESCRIPTION
1. Water Tank
2. Air Intake
3. Bottom lter
4. Door lter
A B
1
42
3
C
C1 C2 C3
C4 C5 C6
TRANSPORT AND HANDLING
Never lift the dryer by holding it at the worktop.
1. Unplug the dryer.
2. Remove the water from the water tank completely.
3. Make sure that door and water tank are properly closed.
4. If the drain hose is connected to your drainage system,
re-connect it to the back of the dryer (see "Installation" section
in the Safety Instruction guide).
Tuotetiedot
| Merkki: | Whirlpool |
| Kategoria: | Kuivausrumpu |
| Malli: | FFT D 8X3B EE |
Tarvitsetko apua?
Jos tarvitset apua merkille Whirlpool FFT D 8X3B EE esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Kuivausrumpu Whirlpool Käyttöohjeet
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
Kuivausrumpu Käyttöohjeet
- Kuivausrumpu Maytag
- Kuivausrumpu Haier
- Kuivausrumpu Bosch
- Kuivausrumpu BEKO
- Kuivausrumpu Grundig
- Kuivausrumpu Electrolux
- Kuivausrumpu Siemens
- Kuivausrumpu Arcelik
- Kuivausrumpu Smeg
- Kuivausrumpu Hoover
- Kuivausrumpu AEG
- Kuivausrumpu Kogan
- Kuivausrumpu Candy
- Kuivausrumpu Gemini
- Kuivausrumpu Panasonic
- Kuivausrumpu Hyundai
- Kuivausrumpu Ufesa
- Kuivausrumpu Blaupunkt
- Kuivausrumpu Eldom
- Kuivausrumpu Philco
- Kuivausrumpu Becken
- Kuivausrumpu Heinner
- Kuivausrumpu Gaggenau
- Kuivausrumpu Zerowatt
- Kuivausrumpu Otsein-Hoover
- Kuivausrumpu Baumatic
- Kuivausrumpu Iberna
- Kuivausrumpu KDK
Viimeisimmät Kuivausrumpu Käyttöohjeet
26 Lokakuuta 2024
25 Lokakuuta 2024
25 Lokakuuta 2024
24 Lokakuuta 2024
24 Lokakuuta 2024
24 Lokakuuta 2024
24 Lokakuuta 2024
24 Lokakuuta 2024
24 Lokakuuta 2024
24 Lokakuuta 2024