Whirlpool FWFP710521WH Käyttöohje
Lue alta 📖 käyttöohje suomeksi merkille Whirlpool FWFP710521WH (8 sivua) kategoriassa Pesukone. Tämä opas oli hyödyllinen 2 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/8
1 “ON/OFF” button
2 Programme selector
3 “Start/Pause” button
4 “Spin” button
5 “Start delay” button
6 “FreshCare+” /
“Key lock“button
7 “Temperature” button
DISPLAY INDICATORS
Door locked
FreshCare+ activated
Start delay activated
Key lock activated
Washing phase
Indicates washing phase of the cycle
Failure: Call Service
Refer to Troubleshooting section
Failure: Water lter clogged
Water cannot be drained; water lter
might be blocked
Failure: No water
No or not sucient inlet water.
In the event of any failure, refer to the
“TROUBLESHOOTING” section
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.
In order to receive a more complete assistance,
please register your product on
www.whirlpool.eu/register
CONTROL PANEL
PROGRAMME CHART
PRODUCT DESCRIPTION
1. Worktop
2. Detergent dispenser
3. Control panel
4. Door handle
5. Door
6. Water lter - behind plinth
7. Plinth (removable)
8. Adjustable feet (4)
1.
2.
7.
3.
4.
5.
6.
8.
DETERGENT DISPENSER
Main wash compartment
Detergent for the main wash, stain remover
or water softener. For a liquid detergent it
is recommended to use removable plastic
partition A (supplied) for a proper dosage.
If powder detergent is used, place the
partition into slot B.
Prewash compartment
Detergent for the prewash.
Softener compartment
Fabric softener. Liquid starch.
Pour in softener or starch solution only up to the “max” mark.
Release button
Press to remove tray for cleaning.
A
B
Max load 7 Kg
Power consumption in o-mode 0.5 W / in left-on mode 8.0 W Detergents and additives Recommended
detergent
Residual
dampness % *
Energy
consumption
kWh
Total water lt
Programme
Temperatures Max. spin
speed
(rpm)
Max
load
(kg)
Duration
(Minutes)
Prewash Main
wash Softener
Powder Liquid
Default Range
Mixed 40°C - 40°C 1000 3.5 ** — —— — —
White 60°C - 90°C 1000 7.0 ** (90°) — — —
Cotton 40°C - 60°C 1000 7.0 220 — 62 0.98 75
Cotton 60°C - 60°C 1000 7.0 275 — 62 0.89 49
Sport 40°C - 40°C 600 3.5 ** — —— — —
Duvet 30°C - 30°C 1000 2.0 ** — —— — —
Jeans 40°C - 40°C 800 3.5 ** — —— — —
Spin & Drain — — 1000 7.0 ** — — — — — — — —
Rinse & Spin — — 1000 7.0 ** — — — — — — —
Rapid 30’ 30°C - 30°C 800 3.0 ** — —— — —
Colours 15° 15°C 15°C 1000 3.5 ** — —— — —
Wool 40°C - 40°C 800 1.5 ** — —— — —
Delicates 30°C - 30°C — 1.0 ** — —— — —
Synthetics 40°C - 60°C 1000 4.0 195 — 33 0.75 72
Dosing required Dosing optional
This data may dier in your home due to changing conditions in inlet water
temperature, water pressure etc. Approximate programme duration values refer to the
default setting of the programmes, without options.
* After programme end and spinning with maximum selectable spin speed, in default
programme setting.
** The duration of the programme is shown on the display.
The washer adapts water, energy and programme duration to your wash load
Cotton - Test wash cycles in compliance with regulations 1061/2010
These are the reference programs for the energy label. Set this wash cycle with a
temperature of 60°C. They are the most ecient programmes in terms of energy and
water consumption for washing normally soiled cotton laundry. The actual water
temperature may dier from the declared one.
For all Test Institutes
Long wash cycle for cottons: set wash cycle with a temperature of 40°C.Cotton
Synthetic program along: set wash cycle Synthetics with a temperature of 40°C.
EN
Quick guide
Wool
CottonDelicates
Mixed
Synthetics
Duvet
Rinse & Spin Jeans
Rapid 30’
Spin & Drain
White
Cotton
Colours 15°
Sport
6.7.
2.1. 3. 4. 5.
Before using the appliance carefully read the Safety Instruction.
Before using the machine, it is imperative that the transport bolts are removed.
For more detailed instructions on how to remove them, see the Installation Guide.
PROGRAMMES
For choosing the appropriate programme for your kind of
laundry, always respect the instructions on the care labels
of the laundry. The value given in the tub symbol is the
maximum temperature possible for washing the garment.
Mixed
For washing lightly to normally soiled resilient garments in cotton, linen,
synthetic bres and mixed bres.
White
For washing normally to heavily soiled towels, underwear, table and bed
linen, etc in resilient cotton and linen. Only when the temperature is
selected at 90°C the cycle is provided with a prewash phase before main
washing phase. In this case it is recommended to add detergent both, in
the prewash and main wash section.
Cotton
Normally to heavily soiled and robust cottons .
Cotton
For washing normally soiled cotton garments. At 60°C, this is the standard
cotton programme and the most ecient in terms of water and energy
consumption.
Sport
For washing lightly soiled sports clothing (tracksuits, shorts, etc.). For best
results, we recommend not exceeding the maximum load indicated in
the ‚‘‘PROGRAMME CHART‘‘. We recommend using liquid detergent , and
adding the amount suitable for half-load.
Duvet
Designed for washing eiderdown padded items such as double or single
duvets, cushions and anoraks. It is recommended to load such padded
items in the drum with the edges folded inwards and not to exceed ¾ of
the drum’s volume. For optimal washing, we recommend using a liquid
detergent.
Jeans
Turn garments inside-out before washing and use a liquid detergent.
Spin & Drain
Spins the load then empties the water. For resilient garments. If you
exclude the spin cycle, the machine will drain only
Rinse & Spin
Rinses and then spins. For resilient garments.
Rapid 30’
For washing lightly soiled garments quickly. This cycle lasts only 30
minutes, saving time and energy.
Colours 15°
This cycle helps protect colours by washing in cold water (15°C) and uses
less energy to heat the water while still oering satisfactory wash results.
Suitable for lightly soiled, unstained garments. This cycle oers wash
results comparable to 40°c mixed at just 15°C
Wool
All wool garments can be washed using programme ‚“Wool“ even
those carryng the “hand-wash only “ label. For best results, use special
detergents and do not exceed max kg declaration of laundry.
Delicates
For washing particularly delicate garments. Preferably turn garments
inside out before washing.
Synthetics
For washing soiled garments made from synthetic bres (such as
polyester, polyacrylic, viscose, etc.) or cotton/synthetic blends.
FIRST TIME USE
To remove any manufacturing debris select the “Cotton” programme
at a temperature of 60°C. Pour a small quantity of detergent powder into
the main wash compartment of the detergent dispenser (maximum
1/3 of the quantity the detergent manufacturer recommends for lightly
soiled laundry). Start the programme without adding any laundry.
DAILY USE
Prepare your laundry according to the recommendations in the “HINTS
AND TIPS” section. Load the laundry, close the door, open the water tap
and press the “ON/OFF” button to switch the wasching machine on,
the “Start/Pause” button ashes. Turn the programme selector to the
desired programme and select any option if needed. The temperature
and spin speed can be changed by pressing the “Temperature”
button or the “Spin” button. Pull out the detergent dispenser and
add the detergent (and additives/softener) now. Observe the dosing
recommendations on the detergent pack. Then close the detergent.
STARTING CYCLE
Press the “Start/Pause” button.
The machine will lock the door ( symbol on) and the drum will start to
rotate; the door will be unlocked ( symbol OFF) and then locked again (
symbol on) as preparation phase of each washing cycle. The “Clicking”
noise is part of the door locking mechanism. Water will enter the drum
and start the washing phase once the door is locked.
PAUSE A RUNNING PROGRAMME
To pause the wash cycle, press the “Start/Pause” ; the indicator light
will go o and the remaining time on display ash. To start the wash cycle
from the point at which it was interrupted press the button again.
OPEN THE DOOR, IF REQUIRED
After starting a programme, the “Door locked” indicator lights up to
show that the door can not be opened. As long as a wash programme is
running, the door remains locked. To open the door while a programme
is in progress, press the “Start/Pause” to pause the programme.
Provided the water level and/or temperature is/are not too high, the
“Door locked” indicator light goes o and you can open the door.
For example to add or remove laundry. Press the “Start/Pause” button
again to continue the programme.
PROGRAMME END
The “Door locked” indicator light goes o and the display shows
“End”. To switch o the washing machine after programme ends press the
“ON/OFF” button, the lights goes o. If you do not press “ON/OFF”
button, the washing machine will switch o automatically after about
a half of an hour. Close the water tap, open the door and unload the
washing machine. Leave the door ajar to allow the drum to dry.
OPTIONS
! If the selected option is incompatible with the programme set,
the incompatibility will be signalled by a buzzer (3 beeps) and the
corresponding indicator light will ash.
! If the selected option is incompatible with another previously set
option, only the most recent selection will remain active.
Start delay
To set the selected programme to start at a later time, press the button
to set the desired delay time. Symbol lights on the display when this
fuction is enabled. To cancel the delayed start, press the button again
untile the value ‚‘‘0‘‘ is shown on the display.
FreshCare+
This option enhances washing performance by generating steam
to inhibit the proliferation of the main bad odour sources inside the
machine. After steam phase, the washing machine will perform gentle
tumbling through slow rotations of the drum. FreshCare+ option starts
after the cycle ends for a maximum duration of 6h and you can interrupt
it at any time by pressing any button on control panel or turning the
knob. Wait around 5 minutes before door can be opened.
Temperature
Every programme has a predened temperature. If you want to change
the temperature, press the “Temperature” button. The value appears
on the display.
Spin
Every programme has a predened spin speed. If you want to change the
spin speed, press the “Spin” button. The value appears on the display.
Demo mode
This appliance is equipped with Demo mode function. For more
information see the USER MANUAL/ Demo Mode.
KEY LOCK
To lock the control panel, press and hold the “Key lock” button for
approximately 3 seconds. When the display visualises a key symbol
, the control panel is locked (with the exception of the “ON/OFF”
button). This prevents unintentional changes to programmes, especially
with children near the machine. To unlock the control panel, press and
hold the “Key lock” button for approximately 3 seconds again.
BLEACHING
If you wish to bleach the laundry, load the washing machine and set the
“Rinse & Spin” programme .
Start the machine and wait for it to complete the rst water lling cycle
(roughly 2 minutes). Put the machine in pause mode by pressing the
“Start/Pause” button, open the detergent drawer and pour the bleach
(observe the recommended doses indicated on the package) into the
main wash compartment where the partition was previously mounted.
Restart the cycle by pressing the “Start/Pause” button.
If desired, it is possible to add fabric softener into the appropriate
compartment of the detergent drawer.
HINTS AND TIPS
Sort your laundry according to
Type of fabric/care label (cotton, mixed bres, synthetics, wool, handwash
items). Colour (separate coloured and white items, wash new coloured
items separately). Delicates (wash small items – like nylon stockings – and
items with hooks – like bras – in a cloth bag or pillow case with zip).
Empty all pockets
Objects like coins or lighters can damage your laundry as well as the
drum.
CLEANING & MAINTENANCE
For any cleaning and maintenance, switch o and unplug the washing
machine. Do not use ammable uids to clean the washing machine.
Cleaning the outside of the washing machine
Use a soft damp cloth to clean the outer parts of the washing machine.
Do not use glass or general purpose cleaners, scouring powder or similar
to clean the control panel – these substances might damage the printing.
Checking the water supply hose
Check the inlet hose regularly for brittleness and cracks. If damaged,
replace it by a new hose available through our After-Sales Service or
your specialist dealer. Depending on the hose type: If the inlet hose has
a transparent coating, periodically check if the colour intensies locally. If
yes, the hose may have a leak and should be replaced
Cleaning the mesh lters in the water supply hose
Close the tap and loosen the inlet hose on the tap. Clean the internal
mesh lter and screw the water inlet hose back onto the tap. Now
unscrew the inlet hose on the rear of the washing machine. Pull o the
mesh lter from the washing machine connection with universal pliers
and clean it. Ret the mesh lter and screw the inlet hose on again. Turn
on the tap and ensure that the connections are completely water-tight.
Cleaning the water lter / draining residual water
If you used a hot wash programme, wait until the water has cooled down
before draining any water. Clean the water lter regularly, to avoid that
the water cannot drain after the wash due to obstruction of the lter. If
the water cannot drain, the display indicates that the water lter may be
clogged.
Remove the plinth by using the screwdriver: push downwards one side
of the plinth with your hand, then push the screwdriver into the gap
between plinth and front panel and pry open the plinth. Place a broad,
at container beneath the water lter, to collect the drain water. Slowly
turn the lter counterclockwise until water ows out. Let the water ow
out, without removing the lter. When the container is full, close the
water lter by turning it in clockwise. Empty the container. Repeat this
procedure until all the water has drained. Lay a cotton cloth beneath the
water lter, which can absorb a small amount of rest water. Then remove
the water lter by turning it out anti clockwise. Clean the water lter:
remove residues in the lter and clean it under running water. Insert
the water lter and reinstall the plinth: Reinsert the water lter again by
turning it in clockwise direction. Make sure to turn it in as far as it goes;
the lter handle must be in vertical position. To test water tightness of
the water lter, you can pour about 1 liter of water into the detergent
dispenser. Then reinstall the plinth.
ACCESSORIES
Contact our After-Sales Service to check if the following accessories are
available for your washing machine model.
Stacking kit shelf
By which your dryer can be xed on top of your washing machine to save
space and to facilitate loading and unloading your dryer in the higher
position.
TRANSPORT AND HANDLING
Never lift the washing machine by holding it at the worktop.
Pull out the mains plug, and close the water tap. Make sure that door
and detergent dispenser are properly closed. Disconnect the inlet hose
from the water tap, and remove the drain hose from your draining point.
Remove all rest water from the hoses, and x them so that they cannot
get damaged during transport. Ret the transport bolts. Follow the
instructions for removing the transport bolts in the INSTALATION GUIDE
in reverse order.
EN
Quick guide
Tuotetiedot
| Merkki: | Whirlpool |
| Kategoria: | Pesukone |
| Malli: | FWFP710521WH |
Tarvitsetko apua?
Jos tarvitset apua merkille Whirlpool FWFP710521WH esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Pesukone Whirlpool Käyttöohjeet
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
Pesukone Käyttöohjeet
- Pesukone Haier
- Pesukone LG
- Pesukone Bosch
- Pesukone BEKO
- Pesukone Grundig
- Pesukone Hisense
- Pesukone Electrolux
- Pesukone Siemens
- Pesukone Arcelik
- Pesukone Hoover
- Pesukone Hotpoint
- Pesukone Amica
- Pesukone AEG
- Pesukone Artusi
- Pesukone Samsung
- Pesukone Imarflex
- Pesukone Kogan
- Pesukone Midea
- Pesukone Candy
- Pesukone Panasonic
- Pesukone Kluge
- Pesukone Khind
- Pesukone Hitachi
- Pesukone Hyundai
- Pesukone Nevir
- Pesukone Infiniton
- Pesukone Indesit
- Pesukone Cylinda
- Pesukone Philco
- Pesukone ECG
- Pesukone Mx Onda
- Pesukone Meireles
- Pesukone Edesa
- Pesukone IFB
- Pesukone Profilo
- Pesukone Constructa
- Pesukone Tisira
- Pesukone Porter & Charles
- Pesukone LERAN
- Pesukone Zerowatt
- Pesukone Otsein-Hoover
- Pesukone Baumatic
- Pesukone Iberna
- Pesukone Otsein
- Pesukone Svan
- Pesukone Corberó
- Pesukone Pitsos
- Pesukone Eudora
- Pesukone Winia
- Pesukone Butler
Viimeisimmät Pesukone Käyttöohjeet
27 Lokakuuta 2024
27 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
24 Lokakuuta 2024
24 Lokakuuta 2024
24 Lokakuuta 2024
24 Lokakuuta 2024
24 Lokakuuta 2024