Whirlpool TDLR 5040L EU/N Käyttöohje

Whirlpool Pesukone TDLR 5040L EU/N

Lue alta 📖 käyttöohje suomeksi merkille Whirlpool TDLR 5040L EU/N (20 sivua) kategoriassa Pesukone. Tämä opas oli hyödyllinen 2 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/20
1 Programme selector
2 “Start/Pause“ button
3 “Spin“ button
4 “Start delay“ button
5 “Reset“ button
6 Washing phase
INDICATORS
Lid open
Failure: Call Service
Failure: Water lter clogged
Failure: No water
In the event of any failure, refer to the
TROUBLESHOOTING“ section
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.
In order to receive a more complete assistance,
please register your product on
www.whirlpool.eu/register
CONTROL PANEL
PROGRAMME CHART
PRODUCT DESCRIPTION
1. Lid handle
2. Lid
3. Control panel
4. Detergent dispenser
5. Drum
6. Water lter - behind the cover
7. Mobility lever (depending on model)
8. Adjustable feet (x2)
5.
1.
6.
7.
2.
3.
4.
8.
DETERGENT DISPENSER
Main wash compartment
Detergent for the main wash, stain remover or
water softener.
Prewash compartment
Detergent for the prewash.
Softener compartment
Fabric softener. Liquid starch. Bleach.
Pour in softener, starch or bleach solution
only up to the max mark.
Release button
Press to remove tray for cleaning.
Max load 5,0 Kg
Power consumption in o-mode 0,11 W / in left-on mode 0,11 W Detergents and additives Recommended
detergent
Residual
dampness % *
Energy
consumption
kWh
Total water lt
Laundry
temperature °C
Programme
Temperatures Max, spin
speed
(rpm)
Max
load
(kg)
Duration
(h : m)
Pre-
wash
Main
wash Softener
Powder Liquid
Setting Range
Cotton 60°C 40 - 95°C 1000 5,0 2:40 64 0,950 46 55
Jeans 40°C 40°C 1000 4,0 1:30   – –
Hygiene 60°C 60°C 1000 5,0 2:30 – –
Synthetics 40°C 30 - 40°C 1000 3,0 2:15 47 0,630 40 40
Delicates 30°C 30 - 40°C 1000 1,5 0:45   – –
Mixed 40°C 40°C 1000 3,0 1:00 – –
Rapid 15’ 30°C 30°C 1000 3,0 0:15   66 0,150 30 20
Wool/Handwash 40°C 20 - 40°C 1000 1,0 0:35   – –
20°C 20°C 1000 5,0 3:05   62 0,250 46 20
40°C 40°C
951 5,0 3:05 60 0,611 45 34
951 2,5 2:30 62 0,411 36 31
951 1,5 2:30 66 0,455 36 32
Rinse + Spin 1000 5,0 – –
Spin 1000 5,0 – –
Drain – –
  Dosing required Dosing optional
water pressure etc. Approximate programme duration values refer to the default setting of
the programmes, without options. The values given for programmes other than the Eco 40-
60 programme are indicative only.
* After programme end and spinning with maximum selectable spin speed, in default
programme setting
6th Sense - The sensor technology adapts water, energy and programme duration to your
wash load.
Eco 40-60 - Test wash cycle in compliance with EU Ecodesign regulation 2019/2014. The most
ecient programme in terms of energy and water consumption for washing normally soiled
cotton laundry. Display only: spin speed values shown on the display can slightly diers from
the values stated in the table.
For all Test Institutes
Long wash cycle for cottons: set wash cycle Cotton with a temperature of 4C.
Synthetic program along: set wash cycle Synthetics with a temperature of 40°C.
This data may dier in your home due to changing conditions in inlet water temperature,
EN
Quick guide
Before using the appliance carefully read the Safety Instruction.
Before using the machine, it is imperative that the transport bracket is removed.
For more detailed instructions on how to remove it, see the Installation Guide.
1 2 3
54
6
PROGRAMMES
For choosing the appropriate programme for your kind of
laundry, always respect the instructions on the care labels
of the laundry. The value given in the tub symbol is the
maximum temperature possible for washing the garment.
Cotton
Normally to heavily soiled and robust cottons .
Jeans
Turn garments inside-out before washing and use a liquid detergent.
Synthetics
For washing soiled garments made from synthetic fibres (such as
polyester, polyacrylic, viscose, etc.) or cotton/synthetic blends.
Hygiene
This program removes 99 % of bacteria while washing normally to
heavily soiled bed linen, table linen and underwear, towels, shirts etc.
made of cotton and linen.
Delicates
For washing particularly delicate garments. Preferably turn garments
inside out before washing.
Mixed
For washing lightly to normally soiled resilient garments in cotton,
linen, synthetic fibres and mixed fibres.
Rapid 15’
Refresh programme. Briefly worn clothing made of cotton, artificial
fibers and blends with cotton. Use lowest recommended detergent
amount.
Wool/Handwash
All wool garments can be washed using programme “Wool“ even
those carrying the hand-wash only“ label. For best results, use special
detergents and do not exceed max kg declaration of laundry.
Eco 40-60
For washing normally soiled cotton garments declared to be washable
at 40 °C or 60 °C, together in the same cycle. This is the standard cotton
programme and the most efficient in terms of water and energy
consumption.
20 °C
For washing lightly soiled cotton garments, at a temperature of 20 °C.
Rinse + Spin
Separate rinse and intensive spin programme. For robust
laundry.
Spin
Spins the load then empties the water. For robust laundry.
Drain
Drain only - no spinning.
FIRST TIME USE
To remove any manufacturing debris select the “Cotton“ programme
at a temperature of 95°C. Pour a small quantity of detergent powder
into the main wash compartment of the detergent dispenser
(maximum 1/3 of the quantity the detergent manufacturer
recommends for lightly soiled laundry). Start the programme without
adding any laundry.
DAILY USE
Prepare your laundry according to the recommendations in the HINTS
AND TIPS“ section. Load the laundry, close the drum door and check
that it is closed properly. Pour in the detergent and any additives.
Observe the dosing recommendations on the detergent pack. Close the
lid. Turn the programme selector to the desired programme and select
any option if needed. The indicator for the “Start/Pause button
flashes and the indicator for the preset spin speed lights up. The speed
can be changed by pressing the “Spin” button. Open the tap and
press the “Start/Pause” button to start the wash cycle. The “Start/
Pause indicator will lights up and the door will be locked. Due to
variations in load and temperature of inlet water, the remaining time is
newly calculated in certain programme phases.
PAUSE OR CHANGE A RUNNING PROGRAMME
To pause the wash cycle, press the Start/Pause“ button, the
indicator light blinks. Select any new programme, temperature, options
or spin speed if you wish to change those settings. Press the “Start/
Pause“ button again to start the wash cycle from the point at which
it was interrupted. Do not add detergent for this programme.
LID OPEN INDICATOR
Before starting and after the end of a programme, the “Lid open“
indicator lights to show that the lid can be opened. As long as a wash
programme is running, the lid remains locked and must on no account
be forced open. In case you have an urgent need to open it during a
running programme, for example to add more laundry, or to remove
laundry which was loaded by mistake, press the Start/Pause“
button. If the temperature is not too high, the Lid open“ indicator
light turns on. It may last a while until you can open the lid. Press “Start/
Pause“ to proceed with the programme again.
PROGRAMME END
The Lid open“ indicator lights up. Turn the programme selector to
the “O“ position and close the water tap. Open the lid and drum and
unload the machine. Leave the Lid open for some time to allow the
interior of the machine to dry. After about a quarter of an hour, the
washing machine will switch off completely to save energy.
To cancel a running programme before the end of cycle, press the
“Reset“ button for at least 3 seconds. The water is drained out. It may
last a while until you can open the lid.
OPTIONS
! When the combination of programme and additional option(s) is not
possible, the indication lights switch o automatically.
! Unsuitable combinations of options are deselected automatically.
Start delay
To set the selected programme to start at a later time, press the “Delay
Timer” button until the desired delay time indication is illuminated.
The lamp for the “Start delay“ option button lights up, and it goes off
when the programme starts. Once having pressed the “Start/Pause“
button, the countdown of the time delay begins. Number of hours pre-
selected can be reduced by pressing the “Start delay“ button again.
Do not use liquid detergent when activating this option. To cancel
the “Start delay“ turn the programme selector to another position.
Prewash
Only for heavily soiled loads (for example sand, granular dirt). Increases
the cycle time by approximately 15 min. Do not use liquid detergent for
the main wash when activating the Prewash option.
Rapid
Enables quicker washing by shortening the programme duration.
Recommendable for small loads or only lightly soiled laundry.
Intensive rinse
Helps to avoid detergent residues in the laundry by extending the
rinse phase. Particularly suitable for washing baby laundry, for people
suffering from allergies and for areas with soft water.
Energy saver
With a lower temperature and slightly modified washing duration, the
optimum combination of excellent washing results and even lower
energy consumption is achieved.
Spin
Every programme has a predefined spin speed. If you want to change
the spin speed, press the Spin“ button. If spin speed “0“ is selected,
the final spinning is cancelled but intermediate spin peaks remain
during the rinse. The water is drained out only.
BLEACHING
Wash your laundry in the desired programme, Cotton or Synthetics
, adding an appropriate amount of chlorine bleach to the Softener
chamber (close the lid carefully). Immediately after the end of
the programme, turn the “Programme selector” and start the desired
programme again to eliminate any residual bleach smell; if you want,
you can add softener. Never put both chlorine bleach and softener into
the softener chamber at the same time.
HINTS AND TIPS
Sort your laundry according to
Type of fabric/care label (cotton, mixed fibres, synthetics, wool,
handwash items). Colour (separate coloured and white items, wash
new coloured items separately). Delicates (wash small items – like nylon
stockings – and items with hooks – like bras – in a cloth bag or pillow
case with zip).
Empty all pockets
Objects like coins or lighters can damage your laundry as well as the
drum.
Appliance interior
If you never or seldom wash your laundry at 95°C, we recommend to
occasionally run a 95°C programme without laundry, adding a small
amount of detergent, to keep the interior of the appliance clean.
Follow the dosage recommendation / additives
It optimizes the cleaning result, it avoids irritating residues of surplus
detergent in your laundry and it saves money by avoiding waste of
surplus detergent
Use low temperature and longer duration
The most efficient programmes in terms of energy consumption
are generally those that perform at lower temperatures and longer
duration.
Observe the load sizes
Load your washing machine up to the capacity indicated in the
“PROGRAMME CHART table to save water and energy.
Noise and remaining moisture content
They are influenced by the spinning speed: the higher the spinning
speed in the spinning phase, the higher the noise and the lower the
remaining moisture content.
CLEANING & MAINTENANCE
For any cleaning and maintenance, switch off and unplug the washing
machine. Do not use flammable fluids to clean the washing machine.
Clean and maintain your washing machine periodically (at least 4 times
per year).
Cleaning the outside of the washing machine
Use a soft damp cloth to clean the outer parts of the washing machine.
Do not use glass or general purpose cleaners, scouring powder or
similar to clean the control panel – these substances might damage the
printing.
Detergent dispenser
Clean regularly, at least three or four times a year, to prevent detergent
build-up:
Press the release button to release the detergent dispenser and
remove it. A small quantity of water can remain in the dispenser, thus
you should carry it in an upright position. Wash the dispenser using
running water. You can also remove the siphon cap on the back of the
dispenser for cleaning. Replace the siphon cap in the dispenser (if
removed) Reinstall the dispenser by locating the dispensers bottom
tabs into the appropriate openings on the lid, and by pushing the
dispenser against the lid until it locks into place. Make sure that the
detergent dispenser is correctly reinstalled.
Checking the water supply hose
Check the inlet hose regularly for brittleness and cracks. If damaged,
replace it by a new hose available through our After-Sales Service or
your specialist dealer. Depending on the hose type: If the inlet hose has
a transparent coating, periodically check if the colour intensifies locally.
If yes, the hose may have a leak and should be replaced. For water stop
hoses (If available): check the small safety valve inspection
window (see arrow). If it is red, the water stop function was triggered,
and the hose must be replaced by a new one. For unscrewing this hose,
press the release button (if available) while unscrewing the hose.
Cleaning the mesh filters in the water supply hose
Check and clean regularly (at least two or three times a year).
Close the tap and loosen the inlet hose on the tap. Clean the internal
mesh filter and screw the water inlet hose back onto the tap. Now
unscrew the inlet hose on the rear of the washing machine. Pull off the
mesh filter from the washing machine connection with universal pliers
and clean it. Refit the mesh filter and screw the inlet hose on again. Turn
on the tap and ensure that the connections are completely water-tight.
Cleaning the water filter / draining residual water
The washing machine is provided with a self-cleaning pump. The filter
keeps objects like buttons, coins, safetypins etc. which have been left in
the laundry. If you used a hot wash programme, wait until the water has
cooled down before draining any water. Clean the water filter regularly,
to avoid that the water cannot drain after the wash due to obstruction
of the filter. If the water cannot drain, the indicator indicates that the
water filter may be clogged.
Open the filter cover with a coin. Place a broad, flat container beneath
the water filter, to collect the drain water. Slowly turn the filter
counterclockwise until water flows out. Let the water flow out, without
removing the filter. When the container is full, close the water filter by
turning it in clockwise. Empty the container. Repeat this procedure until
all the water has drained. Lay a cotton cloth beneath the water filter,
which can absorb a small amount of rest water. Then remove the water
filter by turning it out anti clockwise. Clean the water filter (remove
residues in the filter and clean it under running water) and the filter
chamber. Make sure the pump impeller (in the housing behind the
filter) is not obstructed. Insert the water filter and close the filter cover:
Reinsert the water filter again by turning it in clockwise direction. Make
sure to turn it in as far as it goes. To test water tightness of the water
filter, you can pour about 1 liter of water into the drum and check that
water does not leak from the filter. Then close the filter cover.
Lid seal
Check the condition of the lid seal periodically and clean it from time to
time with a damp cloth.
Recovering an object that falls between the drum and the tub
If an object accidentally falls between the drum and the tub, you can
recover it thanks to one of the removable drum lifters.
Unplug the washing machine. Remove the laundry from the drum.
Close the drum flaps and turn the drum a half-turn (picture ). Using a a
screw-driver press on the plastic end, while sliding the lifter from left to
right (picture , ) by hand it will fall into the drum. Open the drum. You b c
can recover the object through the hole in the drum. Refit the lifter
from inside the drum: Position the plastic tip above the hole on the
right side of the drum (picture ). Then slide the plastic lifter from right d
to left until it clips. Close the drum flaps again, turn the drum through
half a turn and check the positioning of the blade at all its anchorage
points. Plug the washing machine in again.
TRANSPORT AND HANDLING
Pull out the mains plug, and close the water tap. Disconnect the inlet
hose from the water tap, and remove the drain hose from your draining
point. Remove all rest water from the hoses and washing machine
and fix hoses so that they cannot get damaged during transport. To
facilitate moving the machine, pull the mobility lever situated at the
bottom front (if available on your model) out a little by hand. Pull the
washing machine out to the stop with the foot. Afterwards push the
mobility lever back into the original stable position. Refit the transport
bracket. Follow the instructions for removing the transport bracket in
the INSTALATION GUIDE in reverse order.
abcd
EN
Quick guide

Tuotetiedot

Merkki: Whirlpool
Kategoria: Pesukone
Malli: TDLR 5040L EU/N

Tarvitsetko apua?

Jos tarvitset apua merkille Whirlpool TDLR 5040L EU/N esitä kysymys alla ja muut käyttäjät vastaavat sinulle




Pesukone Whirlpool Käyttöohjeet

Pesukone Käyttöohjeet

Viimeisimmät Pesukone Käyttöohjeet