Alto Terminator II Käyttöohje
Alto
Prosessori
Terminator II
Lue alta 📖 käyttöohje suomeksi merkille Alto Terminator II (16 sivua) kategoriassa Prosessori. Tämä opas oli hyödyllinen 2 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/16
User's Manual
www.altoproaudio.com
Version 1.2 April 18, 2008
English
DIGITAL PROCESSOR
Automatic Feedback Killer
TERMINATOR II
c
All rights reserved to ALTO. All features and content might be changed
without prior notice. Any photocopy, translation, or reproduction of part of this
manual without written permission is forbidden. Copyright 2007 Seikaku Group
SEIKAKU TECHNICAL GROUP LIMITED
NO. 1, Lane 17, Sec. 2, Han Shi West Road, Taichung 40151, Taiwan
http://www.altoproaudio.com Tel: 886-4-22313737
email: alto@altoproaudio.com Fax: 886-4-22346757
NF02949-1.2
O FF
PO WER
O N
INPUT LEVEL dBu
CLIP+18+100
-
10
AUTOMATIC
FEEDBACK
KILLER
TERMINATOR II
CHANNEL 1
CHANNEL 2
BYPASS LIVE MODE VARIATIONS
1 2 3 4 5 6 7 8 9 10 11 1 2 13 14 15 16 17 18 1 9 20 21 2 2 23 24
MUSIC SP EECH MUSIC S PEECH
FILTERS
1/40
CH 1
1/51/80
1/40
CH 2
1/51/80
CH 1
CH 2
CAUTION
RISK OF ELECTRIC SHO CK
DO NOT OPEN
IMPORTANT SAFETY INSTRUCTION
TO REDUCE THE RISK OF ELECTRIC SHOCK
PLEASE DO NOT REMOVE THE COVER OR
THE BACK PANEL OF THIS EQUIPMENT.
THERE ARE NO PARTS NEEDED BY USER
INSIDE THE EQUIPMENT. FOR SERVICE,
PLEASE CONTACT QUALIFIED SERVICE
CENTERS.
WARNING
To reduce the risk of electric shock
and fire, do not expose this equipment
to moisture or rain.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Dispose of this product should
not be placed in municipal waste
and should be separate collection.
11.
12.
Move this Equipment only with a cart,
stand, tripod, or bracket,
specified by the
manufacturer, or
sold with the
Equipment. When
a cart is used, use
caution when
moving the cart /
equipment
combination to
avoid possible
injury from tip-over.
Permanent hearing loss may be caused by
exposure to \ extremely high noise levels.
The US. Government's Occupational Safety
and Health Administration (OSHA) has
specified the permissible exposure to noise
level.
These are shown in the following chart:
According to OSHA, an exposure to high SPL in
excess of these limits may result in the loss of
heat. To avoid the potential damage of heat, it is
recommended that Personnel exposed to
equipment capable of generating high SPL use
hearing protection while such equipment is
under operation.
This symbol, wherever used, alerts you to the
presence of un-insulated and dangerous voltages
within the product enclosure. These are voltages that
may be sufficient to constitute the risk of electric
shock or death.
This symbol, wherever used, alerts you to
important operating and maintenance instructions.
Please read.
Protective Ground Terminal
AC mains (Alternating Current)
Hazardous Live Terminal
ON: Denotes the product is turn ed on.
OFF: Denotes the product is turned off.
The apparatus shall be connected to a mains
socket outlet with a protective earthing
connection.
The mains plug or an appliance coupler is used
as the disconnect device, the disconnect device
shall remain readily operable.
CAUTION
Describes precautions that should be observed to
prevent damage to the product.
Read this Manual carefully before operation.
Keep this Manual in a safe place.
Be aware of all warnings reported
with this symbol.
Keep this Equipment away from water and
moisture.
Clean it only with dry cloth. Do not use
solvent or other chemicals.
Do not damp or cover any cooling opening.
Install the equipment only in accordance with
the Manufacturer's instructions.
Power Cords are designed for your safety. Do
not remove Ground connections! If the plug
does not fit your AC outlet, seek advice from
a qualified electrician. Protect the power
cord and plug from any physical stress to
avoid risk of electric shock. Do not place
heavy objects on the power cord. This could
cause electric shock or fire.
Unplug this equipment when unused for long
periods of time or during a storm.
Refer all service to qualified service personnel
only. Do not perform any servicing other than
those instructions contained within the
User's Manual.
To prevent fire and damage to the product,
use only the recommended fuse type as
indicated in this manual. Do not short-circuit
the fuse holder. Before replacing the fuse,
make sure that the product is OFF and
disconnected from the AC outlet.
HOURS X DAY
EXAMPLE
8
6
4
3
2
1,5
1
0,5
0,25 or less
SPL
90
92
95
97
100
102
105
110
115
Small gig
train
Subway train
High level desktop monitors
Classic music concert
Rock concert
Tuotetiedot
| Merkki: | Alto |
| Kategoria: | Prosessori |
| Malli: | Terminator II |
Tarvitsetko apua?
Jos tarvitset apua merkille Alto Terminator II esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Prosessori Alto Käyttöohjeet
16 Tammikuuta 2025
16 Tammikuuta 2025
16 Tammikuuta 2025
16 Tammikuuta 2025
16 Tammikuuta 2025
16 Tammikuuta 2025
16 Tammikuuta 2025
16 Tammikuuta 2025
16 Tammikuuta 2025
16 Tammikuuta 2025
Prosessori Käyttöohjeet
- Prosessori HP
- Prosessori Bose
- Prosessori Christie
- Prosessori Henry Engineering
- Prosessori Smart-AVI
- Prosessori Helix
- Prosessori SPL
- Prosessori QSC
- Prosessori Radial Engineering
- Prosessori MyMix
- Prosessori Atlas Sound
- Prosessori Allen & Heath
- Prosessori Ashly
- Prosessori MuxLab
- Prosessori Lectrosonics
- Prosessori TC Helicon
- Prosessori Bogen
- Prosessori ART
- Prosessori Decimator
- Prosessori Intel
- Prosessori Audibax
- Prosessori Sonifex
- Prosessori BSS Audio
- Prosessori Drawmer
Viimeisimmät Prosessori Käyttöohjeet
15 Tammikuuta 2025
15 Tammikuuta 2025
15 Tammikuuta 2025
15 Tammikuuta 2025
14 Tammikuuta 2025
11 Tammikuuta 2025
11 Tammikuuta 2025
9 Tammikuuta 2025
9 Tammikuuta 2025
9 Tammikuuta 2025