Noise Engineering Sono Abitus Käyttöohje
Noise Engineering
Prosessori
Sono Abitus
Lue alta 📖 käyttöohje suomeksi merkille Noise Engineering Sono Abitus (3 sivua) kategoriassa Prosessori. Tämä opas oli hyödyllinen 3 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/3
1
Noise Engineering
Sono Abitus
Stereo balanced ¼” TRS output and ¼” headphone
output with separate level controls in 4 HP.
Type Headphone amplier and
balanced line output
Size 4 HP
Depth 1.5 inches
Power 2x5 Eurorack
+12 mA 50
-12 mA 50
+5 mA 0
Overview
Sono Abitus is a high-quality output module. It has a stereo pair of Eurorack-level ⅛”
inputs that feed a pair of ¼” TRS jacks for line output and a ¼” headphone output. The
headphone output and line outputs have separate level controls, making it easy to
monitor while performing or recording.
Etymology
Sono -- from Latin: “to make a noise”
Abitus -- from latin: “way out, exit”
“Make noises exit”
WARNING
The headphone output can be EXTREMELY loud. In a normal, quiet environment, the
rst 25% of the knob will probably cover all the volume range you’ll need. Use caution
when listening on headphones (or in general!) as high audio levels can cause
permanent hearing damage. Protect those earholes.
2
Power
To power your Noise Engineering module, turn o your case. Plug
one end of your ribbon cable into your power board so that the red
stripe on the ribbon cable is aligned to the side that says -12v and
each pin on the power header is plugged into the connector on the
ribbon. Make sure no pins are overhanging the connector! If they
are, unplug it and realign.
Line up the red stripe on the ribbon cable so that it matches the
white stripe and/or -12v indication on the board and plug in the
connector.
Screw your module into your case BEFORE powering on the
module. You risk bumping the module’s PCB against something
metallic and damaging it if it’s not properly secured when powered
on.
You should be good to go if you followed these instructions. Now
go make some noise!
A nal note. Some modules have other headers -- they may have
a dierent number of pins or may say NOT POWER. In general,
unless a manual tells you otherwise, DO NOT CONNECT THOSE
TO POWER.
Warranty
Noise Engineering backs all our products with a product warranty: we guarantee our
products to be free from manufacturing defects (materials or workmanship) for one year
from the date of the original retail purchase (receipt or invoice required). The cost of
shipping to Noise Engineering is paid by the user. Modules requiring warranty repair will
either be repaired or replaced at Noise Engineering's discretion. If you believe you have
a product that has a defect that is out of warranty, please contact us.
This warranty does not cover damage due to improper handling, storage, use, or abuse,
modications, or improper power or other voltage application.
Interface
Phones: Volume control for the headphone output.
Master: Volume control for the line outputs.
L/R (⅛”): Eurorack input; sent to both the headphone
output and the line output. The L input is normalized to the
R input if nothing is patched to R. Input levels are displayed
on corresponding LEDs.
Phones (¼”): TRS headphone output. Level is controlled
by Phones knob.
L/R (¼”): Stereo pair of balanced TRS outputs. Level is
controlled by Master knob.
Patch Tutorial
Patch a mix to the L/R input jacks. Connect your
headphones to the Phones output. Connect your speakers,
PA, audio interface, or mixer to the Master outputs with ¼”
TRS cables.
Patching caution
While dicult to do without the use of adapters, please take care not to patch signals
into the headphone and TRS outputs. We take care to protect all our modules from any
voltages that may be encountered in normal patching, but the drivers required in the ¼”
outputs are more delicate than the circuits we usually use and may be damaged from
incoming voltages. Noise Engineering is not responsible for damage caused by
incorrect patching.
Design Notes
When using our cases, both at home and at shows, we struggled to nd an output
module that suited our needs. While there are many options on the market, we needed
one that was small and had level controls for separate headphone and balanced line
outputs. After some searching, we decided to make our own, and Sono Abitus was born.
SA is designed to be a compact and straightforward output solution that will t most
connectivity needs.
3
Tuotetiedot
| Merkki: | Noise Engineering |
| Kategoria: | Prosessori |
| Malli: | Sono Abitus |
Tarvitsetko apua?
Jos tarvitset apua merkille Noise Engineering Sono Abitus esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Prosessori Noise Engineering Käyttöohjeet
19 Maaliskuuta 2025
Prosessori Käyttöohjeet
- Prosessori HP
- Prosessori Bose
- Prosessori Christie
- Prosessori Henry Engineering
- Prosessori Smart-AVI
- Prosessori Helix
- Prosessori SPL
- Prosessori QSC
- Prosessori Black And Decker
- Prosessori Radial Engineering
- Prosessori MyMix
- Prosessori Atlas Sound
- Prosessori Allen & Heath
- Prosessori Ashly
- Prosessori MuxLab
- Prosessori Lectrosonics
- Prosessori TC Helicon
- Prosessori Bogen
- Prosessori ART
- Prosessori Decimator
- Prosessori Intel
- Prosessori Tascam
- Prosessori Alto
- Prosessori Audibax
- Prosessori Sonifex
- Prosessori BSS Audio
- Prosessori Drawmer
Viimeisimmät Prosessori Käyttöohjeet
26 Helmikuuta 2025
16 Tammikuuta 2025
16 Tammikuuta 2025
16 Tammikuuta 2025
16 Tammikuuta 2025
16 Tammikuuta 2025
16 Tammikuuta 2025
16 Tammikuuta 2025
16 Tammikuuta 2025
16 Tammikuuta 2025