Ambient UMP III Käyttöohje

Ambient Mikrofoni UMP III

Lue alta 📖 käyttöohje suomeksi merkille Ambient UMP III (4 sivua) kategoriassa Mikrofoni. Tämä opas oli hyödyllinen 6 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/4
Schleissheimer Straße 181 C | DE +49 89 360 55 10 80797 Munich | phone -0 | www.ambient.de/en | info@ambient.de
© 2020, Ambient Recording GmbH
Universal Microphone Power Supply
Instruction Manual
Schleissheimer Straße 181 C | DE +49 89 360 55 10 80797 Munich | phone -0 | www.ambient.de/en | info@ambient.de
© 2020, Ambient Recording GmbH
P reparing the UMP III
- P ush the battery lever on the bottom in and slide right (direction MIC connector)
- Insert battery with the polarity protection gap to the left when looking at the
front
- Close the door and push back to the left
Power on
Plug in the Mic In cable. The device can only be switched on with the Mic In cable
connected.
Press the button until the LED turns from red to green, release. The LED will now display
the current power setting.
Schleissheimer Straße 181 C | DE +49 89 360 55 10 80797 Munich | phone -0 | www.ambient.de/en | info@ambient.de
© 2020, Ambient Recording GmbH
Power settings LED color:
Blue (default): 48V Phantom
White: 12V Phantom
Yellow: 12V T- Power
Red: Low battery, approx. 15min operation left
Note: Default setting is 48V phantom, but the unit will retain a previously selected mode. To
prevent damage caused by improper power mode, check the current active setting matches
your microphone before connecting it.
Check the setting while unit is on briefly tap the button. The Led will blink in the color of
the active setting.
Changing the power setting
Alternate between 48V and 12V Phantom briefly tap the button twice. The unit will light :
up the setting it would switch to. If you want to confirm, tap while LED is lit, to cancel,
wait. The unit will now blink 3 times in the color of the now active mode.
Enabling T-Power: tap 3 times. The LED will light up yellow. To confirm, tap the button
while LED is lit yellow. The un will blink 3 times yellow to indicate Tit -Power is now
activated.
Disabling T-Power: tap button twice. The Led will light up blue. To confirm selection tap
button while LED is lit. The unit will blink 3 times blue to indicate 48V Ph is now
activated.

Tuotetiedot

Merkki: Ambient
Kategoria: Mikrofoni
Malli: UMP III

Tarvitsetko apua?

Jos tarvitset apua merkille Ambient UMP III esitä kysymys alla ja muut käyttäjät vastaavat sinulle




Mikrofoni Ambient Käyttöohjeet

Mikrofoni Käyttöohjeet

Viimeisimmät Mikrofoni Käyttöohjeet

Comica

Comica VP3 Käyttöohje

2 Huhtikuuta 2025
Atlas Sound

Atlas Sound MWHHM Käyttöohje

2 Huhtikuuta 2025
Synco

Synco G2A1 Käyttöohje

2 Huhtikuuta 2025
Synco

Synco PX Käyttöohje

2 Huhtikuuta 2025
Synco

Synco MC3 LITE Käyttöohje

2 Huhtikuuta 2025
Synco

Synco G2A2 Käyttöohje

2 Huhtikuuta 2025
Synco

Synco G1A1 Käyttöohje

2 Huhtikuuta 2025
Synco

Synco G1 Pro Käyttöohje

2 Huhtikuuta 2025