AXESS AX-BXLOC2-PRO Käyttöohje

AXESS Ei luokiteltu AX-BXLOC2-PRO

Lue alta 📖 käyttöohje suomeksi merkille AXESS AX-BXLOC2-PRO (8 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 3 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/8
AX-BXLOC2-PRO
I N S TA L L A T I O N I N S T R U C T I O N S
MetraOnline.com © COPYRIGHT 2023 METRA ELECTRONICS CORPORATION REV. 8/18/23 INSTAX-BXLOC2-PRO
TABLE OF CONTENTS
Quick Start Guide
Things to Know 2 .................................................
Connections .......................................................2
Gain setup
Basic setup 3 .........................................................
Advanced Setup 3 ................................................
Setting up Bass-X 4 ..................................................
Feature Breakdowns 5 .............................................
Quick Reference 6 .....................................................
Diagram 7 ..................................................................
Specifications 8 .........................................................
Premium Active LOC with Bass Restoration 2 IN - 4 OUT, Input Of 400 Watts Per Channel, 40v Max
TOOLS RECOMMENDED
• Digital Multi-meter
• Test Tones
Universal Premium LOC
The Axxess AX-BXLOC2-PRO is a compact premium line output converter with active input circuitry, which allows it to accept speaker-level signals
of up to 400 watts per channel from factory-installed source units or amplifiers. It converts them to high-quality pre-amp signals that can then
be directed to aftermarket amplifiers. The offers for those factory radios or amplifiers that stop passing AX-BXLOC2-PRO Built In Load Resistors
audio when OE speakers are disconnected. The built in load resistors trick the factory equipment to pass audio into the Axxess LOC allowing easy
audio upgrades. Many of these factory audio systems regulate lower frequencies to prevent potential damage to the OE speakers, which is not a
desirable feature when wanting to add subwoofers to your OE system. Some OE radios and amplifiers can reduce the output of low frequencies
as the volume is increased. Having a product with a Bass-X restoration circuit in the LOC will allow users to enjoy their music as it was recorded.
Users can enjoy maximum sound quality while maintaining the use of factory volume and steering wheel controls. A bass remote control with
digital voltmeter is included, so that you can monitor your car audio amplifier voltage to prevent damage to all your car audio equipment.
Bass Knob AX-BXLOC2-PRO Line Out Converter (LOC)
COMPONENTS
2
THINGS TO KNOW
1. This is an active LOC and MUST have constant 12 volt and a good ground to operate properly.
Having a poor ground can induce noise into your system, use the same gauge wire as the
12 volt line.
2. Determine a suitable mounting location. Make sure you can access all controls and
connections.
3. When ready to mount your LOC, check under your selected mounting location to make sure
it is clear of any wiring harnesses, fuel or brake lines, or anything else that may affect the
vehicle safety.
QUICK START GUIDE
CONNECTIONS
1. Connect your 12 volt and ground wires to the terminals. 14-16 gauge wire is recommended.
2. Turn On Mode DC Offset By default the LOCs is set to . Other turn on options are available
and described in the portion of this manual.Turn On Signal Feature Breakdown
3. Speaker Input Connecting your can happen in a few different places based on your factory
system.
If your vehicle doesn’t have an OE amplifier your best option is to use the speaker wires a.
located behind the radio. Your LOC only requires two inputs, we recommend a left
and right signal full range signal.
If your vehicle has an OE amplifier your best option is to use the speaker wires on b.
the output side of your factory amplifier, look for a full range signal.
4. Find a suitable mounting location of the and run the control wire to that location Bass Knob
in the vehicle. The included offers a voltage display and control ofBass Knob Bass Output
levels.
5. Red Black, Gray, White Connect your RCAs. RCAs are for the right channel. or are for the left
channels. An explanation of the RCA’s and are described in the Main Output Bass Output
Feature Breakdown portion of this manual.
3
REV. 8/18/23 INSTAX-BXLOC2-PRO
GAIN SETUP
Setting gains is very important, if done incorrectly you can damage your speakers. It is
recommended that all settings be adjusted by a professional. have a maximum Axxess LOCs
output of 9.5v RMS. On average aftermarket amplifiers have a maximum input voltage range of
3-6 volts.
When adjusting the gains it is important to understand the input sensitivity of your aftermarket
equipment and adjust the of the LOC to match. If the output levels of the LOC Output Levels
are increased beyond the input capabilities of the amplifier it will cause the input stage of the
aftermarket amplifier to clip, creating distortion. The fix would be to lower the output levels of
the LOC until the distortion is removed.
Basic Setup - No Tools Required
1. Before turning your system on, set all levels and gains to minimum. This includes the LOC
and all aftermarket amplifiers.
2. Bass, Treble, Balance Fade On your radio make sure all audio adjustments i.e. and are all
Centered Flat Loudness Flat and . Turn off and any preset EQ to .
3. While playing a Pink noise track or a song with dynamic sound, increase radio’s volume to
3/4 of the way up.
4. Adjust the output levels of the LOC slowly until the clipping indicator activates, then reduce
the levels so the indicator light doesn’t come on.
5. Do NOT adjust the amplifier’s gain.
Advanced Setup - Tools Required: Digital Multi-meter, Test Tones
1. During this setup process the RCAs between the LOC and aftermarket amplifier need to be
disconnected. They will be reconnected in .Step 11
2. Minimum Set all levels to on the LOC.
3. Bass, Treble, Balance, and Fade On your radio make sure all audio adjustments are all
Centered Flat Loudness Flatand . Turn off and any preset EQ to .
4. Line Input Maximum Sensitivity Open the manual for the aftermarket amplifier and look for
on the specifications page. This measurement will be in volts. (i.e. 3vrms 6vrms)
5. If setting gains for a full range system, play a 1 kHz tone through your radio into the LOC. If
setting levels for a subwoofer, play a 100 Hz tone from the factory radio into the LOC.
6. Turn the radio all the way up, you should not hear the tone playing.
7. Volts AC Black OUTPUT RCA Using a Digital Multi-meter set to , touch the lead to the shield
and insert the lead to the center of the . You will see a voltage reading Red RCA OUTPUT
show on the Multi-meter’s screen.
8. OUTPUT LEVEL Line Adjust the of the LOC until the voltage shown on the screen matches the
Input Maximum Sensitivity Maximized of the aftermarket amplifier. If the light comes on
before the level is reached reduce until the light is off. OUTPUT LEVEL
9. Repeat Steps 7 8 and for the rear output.
10. Turn the radio’s volume down
11. Connect the RCAs from aftermarket amplifier to the LOC.
12. Adjust the gain on your amplifier(s) to minimum.
13. Refer to the amplifier’s manual if additional adjustments are required.

Tuotetiedot

Merkki: AXESS
Kategoria: Ei luokiteltu
Malli: AX-BXLOC2-PRO

Tarvitsetko apua?

Jos tarvitset apua merkille AXESS AX-BXLOC2-PRO esitä kysymys alla ja muut käyttäjät vastaavat sinulle




Ei luokiteltu AXESS Käyttöohjeet

AXESS

AXESS AXDSPX-BM1 Käyttöohje

25 Lokakuuta 2024
AXESS

AXESS AXDIS-BW122 Käyttöohje

15 Lokakuuta 2024
AXESS

AXESS 99-3303 Käyttöohje

15 Lokakuuta 2024
AXESS

AXESS AXBT-MZ2 Käyttöohje

15 Lokakuuta 2024
AXESS

AXESS AX-ALOC618 Käyttöohje

15 Lokakuuta 2024
AXESS

AXESS ANC-GMH3 Käyttöohje

15 Lokakuuta 2024
AXESS

AXESS ANC-GMH2 Käyttöohje

15 Lokakuuta 2024
AXESS

AXESS ANC-CHH2 Käyttöohje

15 Lokakuuta 2024
AXESS

AXESS AX-AB-CH3 Käyttöohje

15 Lokakuuta 2024
AXESS

AXESS AX-AB-CH4 Käyttöohje

15 Lokakuuta 2024

Ei luokiteltu Käyttöohjeet

Viimeisimmät Ei luokiteltu Käyttöohjeet