AXESS AXPIO-SIL1 Käyttöohje

AXESS Ei luokiteltu AXPIO-SIL1

Lue alta 📖 käyttöohje suomeksi merkille AXESS AXPIO-SIL1 (24 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 4 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/24
AXPIO-SIL1
I N S TA L L AT I O N I N S T R U C T I O N S
AxxessInterfaces.com © COPYRIGHT 2024 METRA ELECTRONICS CORPORATION REV. 7/30/24 INSTAXPIO-SIL1
ATTENTION: With the key out of the ignition,
disconnect the negative battery terminal
before installing this product. Ensure that all
installation connections, especially the air
bag indicator lights, are plugged in before
reconnecting the battery or cycling the ignition
to test this product.
NOTE: Refer also to the instructions included
with the aftermarket radio.
TABLE OF CONTENTS
Speaker Installation...............................................2
Dash Disassembly 2-3 ..............................................
Kit Preparation 4 .......................................................
Connections 5-6 ........................................................
Kit Assembly 7 ..........................................................
Radio Operations 8-9 ...............................................
Chevrolet GMC Silverado/ Sierra 2014-2019 (excluding 2019 WT Trim)
with RPO (I05/I06/I0B)
KIT FEATURES)
Designed for Pioneer DMH-W4600NEX/W4660NEX or DMH-WC5700NEX receivers
Allows for the retention and adjustment of the factory personalization menu
through the Pioneer radio
Provides a visual view of HVAC and gauges on the Pioneer screen (cannot be
adjusted via the screen) (cont. on page 2)
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets • C) Phillips screws 9/32" (4)
Not Shown: Radio Interface, LD-GMLAN09-PIO, LD-GMLAN10-PIO, AXEXH-GM09, AXEXH-GM10, LD-BACKCAM-MOST, LD-GMSWC, AD-EU5, 40-GPS-PIO, PR04AVIC-PIO /
PRO4-PIORCA, LD-AX-SPK, AXUSB-GM6
Visit for more detailed information about the product and up-to-date AxxessInterfaces.com
vehicle specific applications.
WIRING & ANTENNA CONNECTIONS (sold separately)
RGB Extension Cable: Pioneer part # CD-RGB150A
(not sold by Metra)
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• 9/32" socket wrench
A B C
2
KIT FEATURES (cont. from cover)
Complete Plug-n-Play installation
Includes dash kit with Axxess interface and
vehicle-specific T-harness
Includes a 3' USB/AUX/HDMI replacement
cable with panel
Includes radio antenna adaptor for GPS
Provides accessory power (12-volt 10-amp)
Provides NAV outputs (parking brake,
reverse, speed sense)
Retains audio controls on the steering
wheel
Works in both single and dual-zone vehicles
Retains safety chimes through an included
off-board speaker
USB Micro “B” USB updatable
• Dash kit is painted scratch-resistant matte
black to match the factory finish
• For non-amplified vehicles only
KIT FEATURES
(CONT.)
DASH DISASSEMBLY
1. Using the panel removal tool, carefully
unclip and remove the radio/climate
control trim panel. (Figure A)
2. Remove (4) 9/32” screws securing the
radio/climate control panel, then unclip,
unplug and remove the panel. (Figure B)
(Figure A)
(Figure B)
SPEAKER INSTALLATION
Install the provided speaker in the dash prior
to assembling the radio components.
Note: Make sure this is mounted in a location
suitable for the driver to hear. (Audio level
for the speaker can be changed via the radio,
once installed.)
3
REV. 7/30/24 INSTAXPIO-SIL1
DASH DISASSEMBLY
(CONT.)
Tuner box
Onstar module
(Figure C)
(Figure D)
3. Remove (2) 9/32" screws securing the
CD player. Slide the CD player out, then
unplug and remove the CD player.
(Figure C)
4. Unclip and slide out the Onstar module
and tuner box, then unplug and remove
them. (Figure D)
If using the LD-LAN09-PIO:
1. Using the panel removal tool, unclip the
plastic shroud around the steering wheel
column. (Figure E)
2. LD-GMSWC Connect the to the 10-pin
straight row connector located in the
steering column.
3. LD-GMSWC Route the cable through the
steering column into the dash and back
towards the radio area.
4. Remove (3) bolts from the lower trim
cover. Rotate the steering wheel to gain
access to the bolts, then remove the
forward facing bolts. (Figure F)
NOTE: LD-LAN09-PIO If RPO is IO5 or IO6, use the .
If RPO is IOB, use the .LD-LAN10-PIO
(Figure E)
3
2
1
(Figure F)

Tuotetiedot

Merkki: AXESS
Kategoria: Ei luokiteltu
Malli: AXPIO-SIL1

Tarvitsetko apua?

Jos tarvitset apua merkille AXESS AXPIO-SIL1 esitä kysymys alla ja muut käyttäjät vastaavat sinulle




Ei luokiteltu AXESS Käyttöohjeet

AXESS

AXESS AXDSPX-BM1 Käyttöohje

25 Lokakuuta 2024
AXESS

AXESS AXDIS-BW122 Käyttöohje

15 Lokakuuta 2024
AXESS

AXESS 99-3303 Käyttöohje

15 Lokakuuta 2024
AXESS

AXESS AXBT-MZ2 Käyttöohje

15 Lokakuuta 2024
AXESS

AXESS AX-ALOC618 Käyttöohje

15 Lokakuuta 2024
AXESS

AXESS ANC-GMH3 Käyttöohje

15 Lokakuuta 2024
AXESS

AXESS ANC-GMH2 Käyttöohje

15 Lokakuuta 2024
AXESS

AXESS ANC-CHH2 Käyttöohje

15 Lokakuuta 2024
AXESS

AXESS AX-AB-CH3 Käyttöohje

15 Lokakuuta 2024
AXESS

AXESS AX-AB-CH4 Käyttöohje

15 Lokakuuta 2024

Ei luokiteltu Käyttöohjeet

Viimeisimmät Ei luokiteltu Käyttöohjeet