AXESS AXUTR Käyttöohje

Lue alta 📖 käyttöohje suomeksi merkille AXESS AXUTR (8 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 4 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/8
Installation instructions for part AXUTR
REV. 2/3/2020 INSTAXUTR
axxessinterfaces.com metraonline.com © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION
Axxess Integrate
CAUTION!
All accessories, switches, climate controls panels, and
especially air bag indicator lights must be connected before cycling
the ignition. Also, do not remove the factory radio with the key in the
on position, or while the vehicle is running.
The AXUTR is a universal trigger output module that has various user programmable features
combined into one unit. The user programmable features are stored in non-volatile memory.
When triggered, the AXUTR can turn on the outputs as a pulsed, latched or timed.
KIT FEATURES
Features 2-4 .........................................................................
- Feature Chart 4 ................................................................
Wiring Instructions 5-6 ........................................................
Programming the AXUTR 7-8 ...............................................
TABLE OF CONTENTS
Black (-) Chassis ground
Red (+) 12-volt constant/switched
Green (+) 0.8 -16 volt input trigger
Brown (-) Input trigger
Blue (+) 12-volt output -2-amps max
White (-) Output -150 ma. max
Orange (-) Output - 150 ma. max
OFF-ON
Programming switch must be turned off after the AXUTR is programmed!
AXUTR
AXUTR
Basic Description of Features:
There are two inputs, the wire is a positive input that senses voltages as low GREEN
as 0.8-volt and the wire is a negative input, both are tied together internally BROWN
which is, essentially, ONE trigger input. There are 3 separate outputs; the wire is BLUE
a positive 12-volt output which has a maximum current rating of 2-amps. The WHITE
and wires are negative outputs which have a maximum of current rating of ORANGE
150-milliamps. The timed output is user adjustable and can be programmed up to
4 minutes and 15 seconds. What makes the AXUTR unique is that it does not use a
potentiometer to adjust the timer. The timer is set by programming AXUTR minutes
and seconds with a number. The time saved is accurate to the second +7% - 8%.
The basic descriptions below are the features that can be done with the AXUTR.
Each feature is assigned Feature#. Please make note of which Feature# you are
going to use. Other unique projects/installs can also be derived from the AXUTR, so
AXXESS leaves it to the installer’s imagination to experiment with these features.
#1 - Low voltage trigger:
Supplies a 12-volt remote output for an aftermarket amplifier when used with a
stock head unit that does not have a remote output. Use the AXUTR to supply a 12-
volt output from a 5-volt remote source, like from Ford radios. Use on some vehicles
that have a negative antenna output and convert to a positive output.
#2 - Alpine video bypass:
This will automatically bypass Alpine’s flip out monitor video procedure. WARNING!
It is dangerous (and illegal in most states) for the driver to watch the TV/Video
monitor while driving the vehicle. The driver may be distracted from looking ahead
and an accident could occur. Install the AXUTR only in RV and Marine applications
where there is no parking/hand brake to interface to. Do not install the AXUTR
where the driver may be able to view the monitor when driving.
#3 - Latch and unlatch output from a pulsed input:
Turn on headlights, neon lights or radio from an alarm with a momentary output or
from a momentary switch.
#4 - Double pulse output:
Pulses outputs twice when trigger from a constant or pulsed signal. Use for alarm
applications where the unlock wire needs 2 pulses to unlock all doors.
#5 - Closed loop circuit:
Good for monitoring trailers on hitches by triggering an aftermarket alarm if the
trailer is disconnected from the vehicles hitch. Also monitors stereo equipment in
vehicles.
#6 - Pulse extender/Delayed turnoff:
Upon a constant or pulsed trigger, the AXUTR will turn on the outputs. As soon as
the trigger is disconnected, turned off or at the end of a pulse, the timer will count
up to the number of seconds recorded, at which time the outputs will turn off. Good
for turning on headlights at night for convenience. Extend alarms output from 1
second to 3 seconds for Mercedes vacuum door locks. (rev.2)
#7 - Horn honking output:
On older, aftermarket alarms, it may have been difficult to disarm the alarm with the
RF remote when the horn was honking. This will give you a 2 second delay between
honks, allowing you to disarm the alarm. Unique horn honking to distinguish your
vehicle from others. Program between 1 and 5 honks before the 2 second delay.
Features
Continued on the next page
AXUTR
Features (Continued)
#8 - Linear Actuator Controller:
Open/close amplifier racks from a momentary source like from a alarm’s negative
output. Sequence is: Start, Stop, Reverse, and Stop.
#9 - Door lock Pulse generator:
Good for automatically locking and unlocking door locks when ignition is turned on
and off.
#10 - Channel Splitter:
Split 1 channel from an alarm to 2 outputs. Both outputs are user programmable for
pulse, latched or timed output.
#11 - Pulses to constant output:
Counts a number of user programmable pulses within a user programmed time to turn on
the outputs. Good for triggering Vehicle tracking devices that need a constant trigger but the
factory alarm only has a pulsed output when triggered like flashing lights or horn honking.
Keeps factory alarm from triggering Vehicle tracking device when arming or disarming
.
#12 - 3 timers in 1:
Upon a constant trigger, all 3 outputs are user programmable to delay before turning
on outputs or turning on instantly then delay before turning off outputs. Good for
situations where you need more than 1 timer but on a different timer period, without
having multiple modules.
#13 - Pulses to latch/unlatch outputs:
Upon a number of pulses within a user programmable time, the outputs will latch.
Upon a number of pulses within a user programmable time the second time, the
outputs will unlatch. You may program how many pulses to latch and unlatch. Use to
turn on aftermarket driving lights by using existing parking light switch.
#14 - Pulses to pulse output:
Upon number of pulses within a user programmable time, the outputs will pulse.
Example: if you programmed to see 4 pulses, for every 4 pulses the AXUTR sees
within a 5 second time period, the outputs will pulse once.
#15 - Pulses to timed output:
Upon a number of pulses within 5 seconds, the outputs will turn on and delay for the
amount of programmed time, then the outputs will turn off.
#16 - Latching outputs #2:
Good for turning on 2 sets of driving lights with one momentary switch. 1st pulse
will latch one wire. 2nd pulse will unlatch first wire and latch second wire. 3rd pulse
will latch both wires. 4th pulse turns off both wires.

Tuotetiedot

Merkki: AXESS
Kategoria: Ei luokiteltu
Malli: AXUTR

Tarvitsetko apua?

Jos tarvitset apua merkille AXESS AXUTR esitä kysymys alla ja muut käyttäjät vastaavat sinulle




Ei luokiteltu AXESS Käyttöohjeet

AXESS

AXESS AXDSPX-BM1 Käyttöohje

25 Lokakuuta 2024
AXESS

AXESS AXDIS-BW122 Käyttöohje

15 Lokakuuta 2024
AXESS

AXESS 99-3303 Käyttöohje

15 Lokakuuta 2024
AXESS

AXESS AXBT-MZ2 Käyttöohje

15 Lokakuuta 2024
AXESS

AXESS AX-ALOC618 Käyttöohje

15 Lokakuuta 2024
AXESS

AXESS ANC-GMH3 Käyttöohje

15 Lokakuuta 2024
AXESS

AXESS ANC-GMH2 Käyttöohje

15 Lokakuuta 2024
AXESS

AXESS ANC-CHH2 Käyttöohje

15 Lokakuuta 2024
AXESS

AXESS AX-AB-CH3 Käyttöohje

15 Lokakuuta 2024
AXESS

AXESS AX-AB-CH4 Käyttöohje

15 Lokakuuta 2024

Ei luokiteltu Käyttöohjeet

Viimeisimmät Ei luokiteltu Käyttöohjeet