Elmo MN400 Käyttöohje

Elmo Ei luokiteltu MN400

Lue alta 📖 käyttöohje suomeksi merkille Elmo MN400 (1 sivua) kategoriassa Ei luokiteltu. Tämä opas oli hyödyllinen 2 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Lataa PDF
Sivu 1/1
Symptom
Image does
not appear.
Image is dark.
Checking point
- Is the power being supplied normally?
- Is the lens aperture adjusted appropriately?
- Is the cable connected appropriately?
- Is the monitor TV adjusted appropriately?
- Is the Function setting switch set appropriately?
- Is the lens aperture been adjusted
appropriately?
- Is the shutter speed set appropriately?
3 4 Mode Contents
L L 1/60 sec Factory-set.
Decreases flickers when the camera is used in the
L H 1/100 sec illumination in an area with a power supply frequency
of 50Hz, but lowers the sensitivity.
Operates the electronic shutter automatically
AES according to the light intensity of the object and
adjusts the exposure appropriately.
28(1.10)
8(0.31)
80(3.15)
6.8(0.27)
8.9(0.35)
(In air 6.9(0.27))
19(0.75)
φ
21(0.83)
19(0 . 7 5)
CCD image pickup surface
Elmo Color Camera Module
Instruction Manual
Precautions for Installation and Use
•Handle with care. - Do not drop, shock or vibrate this product
excessively, or the product could go out of order. Do not handle
the camera cable roughly, or the camera cable could be
disconnected.
•Do not aim at an intense light. - Do not allow an intense light,
such as a spotlight, to come into the camera screen, blooming
or smearing could occur. Do not direct the camera to the sun,
either, or an intense light could come into the camera and
vertical stripes could appear on the camera screen, though this
is not a symptom of failure.
•Install this product in a place free from noise into the
camera screen. - If the camera is installed or the camera cable
is wired near a lamp line or a TV set, the camera screen could
suffer noise. If this is the case, relocate the camera or cable
routing.
•Keep the camera head and the protective cap from the
reach of infants. - Do not place the camera head or the
protective cap within the reach of infants, or they could
dangerously put it into their mouth or swallow it. The protective
cap is used to protect the CCD image pickup surface; do not
throw it away but safekeep it.
•When leaving the camera unused for a long time - When the
camera is left unused for a long time, shut OFF the power
supply for the safety purpose.
•When maintaining the camera - Shut OFF the power supply to
the camera, and wipe the camera with a dry cloth. If the stain
will not come off, wipe it off with a cloth soaked with a diluted
neutral detergent. Do not use benzine, alcohol or thinner, or the
coating could fall off or the indication could degenerate. For
cleaning the lens, use a lens cleaning paper or the like.
Name and Function of Each Part
Focus lock ring: Locks the
focus of the lens.
CCD
image
pickup
surface
Function setting switch: Sets the white balance
and the shutter speed.
Connection terminal: Use Hirose
HR25-7TP-8P (or equivalent).
Setting the white balance
The white balance can be set to any of the following 4 modes
according to the imaging conditions (light source):
1 2 Mode Contents
The camera checks the color temperature of the light
L L ATW source continuously, and adjusts the white balance
automatically.
H L 3200K For electric bulb (fixed value)
L H 4200K For fluorescent lamp (fixed value)
H H 6300K For outdoor light (fixed value)
Pin No. Contents
1 GND (VIDEO OUT)
2 VIDEO OUT
3 -
4 -
5 -
6 -
7 GND (DC IN)
8 DCIN
About the connection terminal
How to Connect
(1) Attach the lens (option) to the camera body.
(2) Attach the multi-cable (option) to the camera body and
connect the BNC connector of the multi-cable to the VIDEO IN
terminal of a monitor TV or the like.
(3) Connect the DC jack of the multi-cable to the DC plug of the
AC adaptor (option).
• For the information of the lens, multi-cable, AC adaptor,
etc., refer to "Option."
Lens (option)
DC jack
DC plug
AC adaptor
(option)
Monitor TV
BNC connector
Multi-cable
(option)
Camera body
Troubleshooting
5(0.20)
8(0.31) 21.5(0.85 )
9(0.35)
11(0.43)
25(0.98)
11.5(0.45)
11.6 (0.46)
12.5(0.49)
14(0.55)
10.5(0.41)
2-φ3(0.12)
hole
Outside Drawing
Camera body
Camera holder
Specifications
* The design, the specifications, etc. are subject to change
without notice due to continual improvements.
Model MN400
Power input 12VDC (11VDC - 15VDC)
Power consumption Approx. 1.5W (at 12VDC input)
Image pickup device
Type 1/2 color interline transfer system CCD
Effective image Horizontal 768, vertical 494
pickup pixels
Image pickup area Horizontal 6.54mm, vertical 4.89mm
Scanning system 2:1 interlace
Scanning frequency Horizontal 15.734kHz, vertical 59.94Hz
Synchronous system
Internal synchronization
Resolution Horizontal 480TV, vertical 350TV
SN ratio 50dB or more
Standard object 60 lx (F1.6 incandescent lamp)
illuminance
Minimum object 2 lx (F1.6 incandescent lamp)
illuminance
White balance ATW, 3200K, 4200K, 6300K
AGC Built-in (always ON)
Electronic shutter 1/60 sec, 1/100 sec, AES
AES 1/60 sec - 1/100,000 sec
Power terminal 8P round connector
Video terminal
8P round connector, output VBS 1.0V (p-p), 75
Ω
Dimensions Width:19mm (0.75"), height:19mm (0.75"),
depth:80mm (3.15")
Weight Approx. 50g
Ambient temperature
-10 - 40 (14℃ ℃ °F °F- 104 )
Ambient humidity 30 - 90%
Accessories Instruction manual, camera holder
Options
(1) Turn the lens to focus the camera, and then turn the focus lock
ring A counterclockwise to lock the lens.
(2) Turn the draw ring B to adjust the aperture.
CODE Model Length
9888 MNC-03A 3m
9888-1 MNC-10A 10m
Lens
Camera body
Lens mounting
thread portion
Focus lock
ring A
Draw ring B
(Focus unit)
CODE Model Input voltage Rated output
9894 GSU06-3-U 100-240V DC12V 0.5A
+
-φ5.5(0.22)
-
0.03
0
φ2.1(0.08) 0.03
+
-
1
8
234
567
Setting the shutter speed
*Notes for the AES mode
- Adequate light intensity is required.
- Flickers may occur in the fluorescent illumination.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not install near heat sources such as radiators, heat
registers, stoves or other apparatus (including amplifiers) that
produce heat.
8. Do not touch this apparatus during lightning storms.
9. Unplug when unused for long periods of time.
10. Refer all servicing to qualified personnel. Servicing is required
when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled
or objects have been fallen onto the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
WARNING:
Handling the cord on this product or cords associated with
accessories sold with this product, will expose you to lead, a
chemical known to the State of California to cause birth defects
or other reproductive harm.
Wash hands after handling.
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product s enclosure that may be of sufficient magnitude ’
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
CAUTION
• Do not use any power supply other than specified.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
* The CAUTION label is attached on the base of product.
INFORMATION
This equipment has been tested and found to comply with the
limits for Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, use, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to
correct the interference at his own expense.
USER-INSTALLER CAUTION: Your authority to operate this
FCC verified equipment could be voided if you make changes or
modifications not expressly approved by the party responsible for
compliance to Part of the FCC Rules.
WARNING:
Unauthorized recording of copyrighted, materials,
photographs, etc. may infringe on the rights of copyright
owners and be contrary to copyright laws.
Printed on recycled paper
6X1MCCB01
To AC
adaptor
Caution: Using any plug other than the specified could
cause intermittent contact.
Three-leg screw
(1/4-20UNC)
To camera
connecting
terminal Hirose HR25-7TP-8P
or equivalent
BNC
connector
DC jack
To VIDEO IN
terminal of a
monitor TV or
the like
To multi-cable DC jack
<Specified plug>
DC plug
To AC outlet
Model Slim Camera
MN400
All dimensions in mm(inch)
All dimensions in mm(inch)
Lens
Multi-cable
AC adaptor
All dimensions in mm(inch)
ELMO CO., LTD.
6-14, Meizen-cho, Mizuho-ku,
Nagoya, 467-8567 Japan
E-mail : foreign-div@elmo.co.jp
OVERSEAS SUBSIDIARY COMPANIES
and are registered trademarks of
ELMO COMPANY, LIMITED.
ELMO Mfg. Corp.
1478 Old Country Road, Plainview, NY 11803-5034 U.S.A.
Tel.
516-501-1400 Fax. 516-501-0429
E-mail:elmo@elmousa.com
Web:http://www.elmousa.com/
ELMO Canada Mfg. Corp.
44 West Drive, Brampton, Ontario, L6T 3T6, Canada
Tel.
905-453-7880 Fax. 905-453-2391
E-mail:info@elmocanada.com
Web:http://www.elmocanada.com/
ELMO (Europe) G.m.b.H.
Neanderstr. 18, 40233 Dusseldorf, Germany
Tel.
0211-376051-53 Fax. 0211-376630
E-mail:info@elmo.de
Web:http://www.elmo.de/
8771
9264
9250
9265
9266
9819
9267
8797
8797-1
8797-2
9271
9271-1
T183
T204D
T1675F
T2015D
T3124
T4536
T287P
T3425M
T3425MB
T3425MC
T416MA
T416MB
f=3.0mm
f=4.0mm
f=7.5mm
f=15mm
f=24mm
f=36mm
f=7mm
f=25mm close-up฀
f=25mm close-up
f=25mm close-up฀
f=16mm close-up฀
f=16mm close-up฀
1.8
2.0
1.6
2.0
3.1
4.5
2.8
*4.6 - 5.2
*4.3 - 6.0
*6.0 - 8.1
*8.4 - 12.2
*6.3 - 8.4
Max. relative aperture
(f-number)
CODE Model Focal length f
*The f-number represents effective f-number.
H L
H H

Tuotetiedot

Merkki: Elmo
Kategoria: Ei luokiteltu
Malli: MN400

Tarvitsetko apua?

Jos tarvitset apua merkille Elmo MN400 esitä kysymys alla ja muut käyttäjät vastaavat sinulle


Ei luokiteltu Elmo Käyttöohjeet

Elmo

Elmo Huddle Space HS-G2 Käyttöohje

16 Lokakuuta 2024
Elmo

Elmo P30 Käyttöohje

16 Lokakuuta 2024
Elmo

Elmo EV-200 Käyttöohje

16 Lokakuuta 2024
Elmo

Elmo Huddle Space HS-G1 Käyttöohje

16 Lokakuuta 2024
Elmo

Elmo PentaClass A Käyttöohje

16 Lokakuuta 2024
Elmo

Elmo HV-C1000XG Käyttöohje

16 Lokakuuta 2024
Elmo

Elmo TND4004 Käyttöohje

16 Lokakuuta 2024
Elmo

Elmo ESD-CC1 Käyttöohje

16 Lokakuuta 2024
Elmo

Elmo Chroma Quad4 Käyttöohje

16 Lokakuuta 2024
Elmo

Elmo EV-368 Käyttöohje

16 Lokakuuta 2024

Ei luokiteltu Käyttöohjeet

Viimeisimmät Ei luokiteltu Käyttöohjeet

IKEA

IKEA ÅGOTNES 004.808.58 Käyttöohje

27 Lokakuuta 2024
IKEA

IKEA ÅFJÄLL 605.686.50 Käyttöohje

27 Lokakuuta 2024
IKEA

IKEA ÅBYGDA 205.112.41 Käyttöohje

27 Lokakuuta 2024
IKEA

IKEA ÅFJÄLL 305.699.53 Käyttöohje

27 Lokakuuta 2024
IKEA

IKEA ÅBYGDA 204.814.80 Käyttöohje

27 Lokakuuta 2024
IKEA

IKEA ÅFJÄLL 405.686.46 Käyttöohje

27 Lokakuuta 2024
IKEA

IKEA ÅBYGDA 504.814.69 Käyttöohje

27 Lokakuuta 2024
IKEA

IKEA ÅFJÄLL 805.686.30 Käyttöohje

27 Lokakuuta 2024
IKEA

IKEA ÅKREHAMN 104.816.59 Käyttöohje

27 Lokakuuta 2024
IKEA

IKEA ÅNNELAND 004.817.30 Käyttöohje

27 Lokakuuta 2024