EMOS P5712 Käyttöohje

EMOS Ovikello P5712

Lue alta 📖 käyttöohje suomeksi merkille EMOS P5712 (52 sivua) kategoriassa Ovikello. Tämä opas oli hyödyllinen 3 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Sivu 1/52
3402012000_31-P5712_00_01_WEB 105 × 148 mm
www.emos.euwww.emos.eu
P5712
GB Wireless Doorchime
CZ Bezdrátový zvonek
SK Bezdrôtový zvonček
PL Dzwonek bezprzewodowy
HU Vezeték nélküli csengő
SI Brezžični zvonec
RS|HR|BA|ME Bežično zvono
DE Drahtlose Klingel
UA Бездротовий дзвоник
RO|MD Sonerie fără r
LT Belaidis durų skambutis
LV Bezvadu durvju zvans
EE Juhtmeta uksekell
BG Безжичен звънец
FR Sonnette sans fil
IT Campanello senza fil
ES Timbre inalámbrico
NL Draadloze deurbel
2
3
2
1
7
5
4
6
1
2
2
1
3
S2
3
3
GB | Wireless Doorchime
The set consists of a doorbell button (transmitter) and a chime (receiver). The chime is designed for
permanent placement in a room or can be used as a portable „pager“. Transmission between the
button and the chime is carried by 433.92 MHz radio waves. Range depends on local conditions and
reaches up to 100 m in open spaces without interference. For proper usage of the wireless doorchime,
read the instruction manual thoroughly.
Specications
Range: up to 100 m in an open area (can drop down to up to one fth in a busy area)
Pairing the chime with buttons: self-learning function
Pairing capacity: max. 8 buttons
Number of ringtones: 16
Ringtone volume: adjustable in 4 levels
Three dierent modes: audio signalisation only; light signalisation only; light and audio signalisation
Water-resistant button (transmitter) with IP44 enclosure
Working frequency: 433.92 MHz, 10 mW e.r.p.max
Button power supply: 1× 3 V (CR2032) battery
Chime power supply: 3× 1.5 V (AA) batteries
Chime Description (see Fig. 1)
1 – speaker
2 – ringtone change button
3 – bell LED
4 – ringing signalisation setting button
5 – volume setting button
6 – battery compartment
7 – hole for hanging
Button Description (see Fig. 2)
1 – ring button/button LED
2 – hole for opening the battery cover
3 – battery compartment CR2032 – battery for the button
S2 – button for erasing the doorchime‘s memory
Button Installation (see Fig. 3)
Pairing the Button with the Chime
1. Remove the rear cover by inserting a screwdriver into the hole on the side of the button. Insert a
3 V type CR2032 battery into the button. Make sure to observe the correct polarity!
2. Insert 3× 1.5 V AA batteries into the chime. Make sure to observe the correct polarity. Use 1.5 V
alkaline batteries only; do not use rechargeable 1.2 V batteries.
3. Once the batteries are inserted, the chime will switch to self-learning pairing mode, which lasts for
30 seconds. During this time, press the ring button. The LED on the doorbell will ash, the chime
will ring and the button is now paired with the chime. This automatically ends self-learning mode.
4. Re-assemble the button.
5. To pair additional buttons, repeat the process from step 1.
6. You can pair a maximum of 8 buttons this way.
7. Transmission range is 100 m in an open space without electromagnetic interference. The range is
inuenced by local conditions, such as the number of walls through which the signal has to pass,
metal door frames and other elements which aect the transmission of radio signals (presence
of other radio devices operating at a similar frequency, such as wireless thermometers, gate
controls etc.). Transmission range can decrease drastically due to these factors.
8. The chime (receiver) is designed for permanent placement in a room or can be used as a
portable „pager“.
Note: If you pair another button (9th and more), the memory of the rst buttons in descending order
will be automatically erased.

Tuotetiedot

Merkki: EMOS
Kategoria: Ovikello
Malli: P5712

Tarvitsetko apua?

Jos tarvitset apua merkille EMOS P5712 esitä kysymys alla ja muut käyttäjät vastaavat sinulle