Extron DVI-RGB 200 Käyttöohje
Extron
Audio/video-muunnin
DVI-RGB 200
Lue alta 📖 käyttöohje suomeksi merkille Extron DVI-RGB 200 (2 sivua) kategoriassa Audio/video-muunnin. Tämä opas oli hyödyllinen 2 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/2
This guide provides instructions for an experienced installer to set up and operate Extron DVI-RGB 200 ®
DVI to Analog RGB Video Interface.
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources and mount the interface as required.
Step 2 — Connections and Initial Settings
a Connect a single link of direct DVI-D Input connector —
digital video to this DVI-I connector using the included cable.
b Buffered Loop-through connector — If desired, connect a
direct digital local monitor to this DVI-I connector.
NOTE: Use only cables specifically intended for DVI interfaces. Use of non-DVI cables or modified cables can cause
the DVI-RGB 200 to not operate correctly.
c Connect an RGB display to these female BNC connectors. Connect the Output connectors —
BNCs as shown at right for the desired RGB video format.
NOTE: Ensure that the SOG DIP switch (f) is turned off (down) for RGBHV and RGBS
video.
Ensure that the SOG DIP switch is turned on (up) for RGsB video.
d EDID Source switch —
Set this switch to the Monitor (up) position to connect the DDC channel between the direct
digital video source and the local monitor.
Set this switch to the Selector (down) position to connect the DDC channel between the
direct digital video source and the built-in DVI-RGB 200 EDID logic.
e If the EDID Source switch (EDID Select — d) is in the Selector (down) position, set this switch
to the appropriate position to select the desired video resolution. Use the Refresh DIP switch
(f) to select the refresh rate. The table at right identifies the
switch positions and the associated resolutions and vertical
refresh rates.
f DIP switches —
SOG (Sync on Green) On/Off switch — Set this switch to the
On (up) position to enable SOG for RGsB video. Set this switch
to the Off (down) position to disable SOG for RGBS or RGBHV
video.
Refresh switch —
If the EDID Source switch (d) is in the Selector position (down)
and the EDID select switch (e) is in position 1 through F
position, set this switch either up or down to select the refresh
rate of the selected output. See the table at right.
If the EDID Source switch (d) is in the Selector (down) position and the EDID select switch is in position 0, set this switch
up to capture the EDID data from the connected Buffered Loop-through monitor. See Capturing a User-recorder EDID.
g AC power connector — Plug a standard IEC power cord into this connector to connect the interface to a
100 to 240 VAC, 50 Hz or 60 Hz power source.
100-240V 0.4A
OUTPUT
DVI-D INPUT BUFFERED
LOOP-THROUGH
R
H
G
V
B
S
SO G O N/OFF
REFRESH
EDID
SO URCE
MONIT OR
HIG H
LO W
SELECT OR
EDID
SELECT
DVI-RGB 200
50/60 Hz
21 57 364
R
H
G
V
B
S
R
H
G
V
B
S
R
H
G
V
B
S
RGBHV
RGBS
RGsB
Pos. Resolution
EDID Select
Switch
Refresh
DIP Switch
0 User EDID EDID capture
1
2 1024x768
3 1280x720
50 Hz 60
50 Hz 60
50 Hz 60
4
5
1280x768
1280x800
50 Hz 60
50 Hz 60
800x600
< >
Dwn Up
8
9
A
B
1366x768
1400x1050
Pos. Resolution
50 Hz 60
50 Hz 60
C
D
1440x900
1600x1200
50 Hz 50
50 Hz 60
6
7
50 Hz 60
50 Hz 60
E
F
50 Hz 50
50 Hz 60
50 Hz 60
Refresh
DIP Switch
<
>
Dwn Up
EDID Select
Switch
1280x1024
1360x768
1680x1050
1920x1080
1920x1200
N/A
1
DVI-RGB 200 Setup Guide
Operation
Apply power to the devices in the following order: 1) DVI-RGB 200, 2) display device, 3) input device. After all devices are
powered up, the system is fully operational.
If any problems are encountered, verify that the cables are routed and connected properly. If your problems persist, call the
Extron S3 Sales & Technical Support Hotline that is closest to you, at the number shown below.
NOTES: • High-bandwidth Digital Content Protection (HDCP) is an encryption method that protects copyrighted digital
entertainment material that uses DVI video.
• The DVI-RGB 200 cannot respond to the HDCP decryption key. When the DVI input is HDCP encrypted, the
output of the DVI-RGB 200 RGB is blank.
• The computer reads the DDC on power up to determine the direct digital video resolution and refresh rate
to output. Ensure that the local DVI monitor and the RGBHV monitor can both display the selected resolution
and refresh rate, otherwise images may be distorted or missing.
• Ensure that the computer and local monitor are connected to the DVI-RGB 200, and the DVI-RGB 200 and
local monitor have power applied, before applying power to the computer. If the other devices are not
turned on before the computer is powered on, the image will not appear.
Front Panel Controls and Indicator
NOTE: Level Boost and Peaking have no affect on the DVI
output of the Buffered Loop-through connector.
h The two-color Power LED lights amber or Power LED —
green:
Amber when the DVI-RGB 200 is receiving power but no DVI input signal is applied.
Green when the DVI-RGB 200 is receiving power and a DVI input is present.
i Level Boost control — The Level Boost control alters the brightness of the picture on the RGB output. Judge the
adjustment visually by looking at the display.
• At the minimum level setting (the counterclockwise limit of this control), the interface outputs video at 0.7 Vp-p.
• At the maximum level setting (the clockwise limit of this control), the interface outputs video at 1.45 Vp-p.
Select a level setting of 0.7 V and above to compensate for the signal level decrease that occurs with long cables. Set
the level at the maximum setting for cable lengths over 500 feet.
j Peak(ing) control — The Peaking control affects the sharpness of the RGB output. Increased peaking can compensate
for detail (mid- and high-frequency) loss from low bandwidth or long cables. The minimum setting (counterclockwise
limit) provides no peaking. The maximum setting (clockwise limit) provides 100 percent peaking.
Capturing a User-recorded EDID
Record the EDID from a display connected on the Buffered Loop-through connector as follows:
1. Set the rear panel EDID Source switch to the Selector (down) position.
2. Set the Output Resolution switch to the 0 position.
3. Change the Refresh dip switch to on (up).
NOTE: The front panel Power LED lights amber whether the DVI-D Input connector is receiving a signal or not.
4. Connect the display device to Buffered Loop-through connector.unpowered
5. Power on the display device. The DVI-RGB 200 copies the EDID of the display connected in step to its memory.4
After the EDID is successfully copied, the front panel Power LED lights green.
6. Set the Refresh DIP switch to off (down).
68-1791-50
Rev A
10 10
DVI-RGB 200
DVI TO RGB CONVERTER
BOOST
LEVEL
CONT ROL
PEAK
8 9 10
SOG ON/OFF
REFRESH
DDC
SOURCE
MONITOR
HIGH
LOW
SELECTOR
EDID
SELECT
Extron USA - West
Headquarters
+800.633.9876
Inside USA/Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA/Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.833.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
© 2010 . All rights reserved. Extron Electronics www.extron.com
2
DVI-RGB 200 Setup Guide (Continued)
Tuotetiedot
| Merkki: | Extron |
| Kategoria: | Audio/video-muunnin |
| Malli: | DVI-RGB 200 |
Tarvitsetko apua?
Jos tarvitset apua merkille Extron DVI-RGB 200 esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Audio/video-muunnin Extron Käyttöohjeet
16 Lokakuuta 2024
Audio/video-muunnin Käyttöohjeet
- Audio/video-muunnin D-Link
- Audio/video-muunnin StarTech.com
- Audio/video-muunnin Sitecom
- Audio/video-muunnin INOGENI
- Audio/video-muunnin RME
- Audio/video-muunnin MuxLab
- Audio/video-muunnin Evolution
- Audio/video-muunnin PureLink
- Audio/video-muunnin ATen
- Audio/video-muunnin Blustream
- Audio/video-muunnin Trendnet
- Audio/video-muunnin Intellinet
Viimeisimmät Audio/video-muunnin Käyttöohjeet
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
26 Lokakuuta 2024
25 Lokakuuta 2024
25 Lokakuuta 2024
24 Lokakuuta 2024
24 Lokakuuta 2024
23 Lokakuuta 2024
22 Lokakuuta 2024