Extron FF 120T Käyttöohje
Lue alta 📖 käyttöohje suomeksi merkille Extron FF 120T (4 sivua) kategoriassa Kaiutin. Tämä opas oli hyödyllinen 5 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/4
1
Product Category
IMPORTANT:
Refer to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
FF 120T • Setup Guide
This setup guide contains installation information about the Extron FF 120T Flat Field® speaker. This speaker is designed for use
in plenum rated ceiling spaces and can be dropped into a standard 2 feet by 2 feet or 2 feet by 4 feet (with supplied cross bars)
false ceiling tile space on a T-bar grid.
WARNING: May result in serious injury. Installation and service must be performed by authorized personnel only.
Factors to Consider Before Installation
zAll wiring and electrical connections must conform to all applicable building codes and local ordinances.
zInstallation in a plenum-rated environment requires plenum rated cable or conduit.
Number of Wires
per Connection Point Maximum
Wire Gauge
1 12 GAW
2 14 GAW
1 14 GAW
2 16 GAW
Wire Gauge Table
8Ω
Configuration
70 V/100 V
Configuration
zIf using secondary support cables, the installer provides the cables.
Installation
1. Disconnect power — Power down all attached devices before proceeding.
2. Remove and cut ceiling tile — Remove the ceiling tile where the FF 120T will be installed. Cut out a 12-inch section from
either end of the tile where the speaker will be installed, as shown below.
48”
24”
12”
End Section
24” x 48” Ceiling Tile 24” x 24” Ceiling Tile
24”
24”
12”
Dr Lineaw
Cut Material
3. Install the T-rail — Install the T-rail crosspiece into the ceiling opening
up against the cut tile.
T-rail (1)
4. Transformer cover plate — Loosen, but do not remove, the two screws on the top of the
transformer cover plate, as shown at right. Next, slide and remove the transformer cover plate,
which is installed with the transformer side down.
Transformer
Cover Plate
Loosen, Do Not Remove
2
FF 120T • Setup Guide (Continued)
5. Using Flexible Conduit — When using exible conduit, insert the conduit into the cover plate opening using an appropriate
conduit adapter, and secure the conduit to the plate as shown below.
Flexible Conduit Adapter
Flexible Conduit
Transformer Cover Plate
Secondary Attachment
Point
Rear of Speaker
When using speaker wires without a conduit, secure the cable clamp
adapter (included) to the transformer cover plate and insert the wires
through the clamp. Tighten the screws as shown at right.
6. Distributed audio system (70 V or 100 V) or direct connection —
• if wiring a 100 V or 70 V distributed system and using the transformer, proceed to step 7.
• if bypassing the transformer and wiring directly from the amplier, proceed to step 9.
7. Connect cables from the amplier to the transformer on the FF 120T transformer cover plate.
Amplifier
70 V or 100 V Distribution System
(through the transformer)
FF 120T
Additional FF 120Ts
can be attached to
to the tap connector.
See step .7f
TransformerTransformer
FF 120T
Black (-)
To Additional
Speaker
Red (+)
Red (+)
Black (-)
From Amplifier
(70V/100V)
(Red) To Speaker
(+) Terminal
(Black) To Speaker
(-) Terminal
NC
1 W
2 W4 W8 W16 WCOM
70 V
100 V
COM NC 16 W 8 W 4 W W 1 W
a. Pull the wires from the amplier through and out of the conduit, if a conduit is used.
b. Route the two wires from the amplier through the cover plate hole to the transformer side. See the wire gauge table on
page .1
c. Strip 3/16" (5 mm) from the wire ends and keep the wire end strands together by twisting them. Do not tin the wires.
Cable Clamp Adapter
Transformer Cover Plate
Secondary Attachment
Point
Rear of Speaker
3
Product Category
d. Secure the wires to the appropriate taps on the captive screw connectors
of the 7-connector terminal block (on the transformer side of the cover plate)
as indicated on the tap label (see the note below). The black
negative (-) wire attaches to the “COM” terminal, and the red
positive (+) wire attaches to the desired terminal tap
(see the diagram at right).
NOTE: Observe the 70 V or 100 V system designation
as indicated on the tap label.
NC1 W2 W4 W8 W16 WCOM
70 V100 V
COM NC 16 W 8 W 4 W 2 W 1 W
e. Use a small at blade screwdriver to tighten the terminal
block screws.
f. To wire additional speakers, route speaker wires
from the second speaker through the cover plate
hole to the transformer side. Twist the black negative (-)
wires together and the red positive (+) wires together before
inserting them into the terminal block. Additional speakers can be
daisy-chained this way, as shown at right.
8. Connect wires from the transformer to the speaker.
a. Keep the wire strands together by twisting them (do not tin the wires).
b. Connect the red positive (+) wire to the + speaker terminal and connect the black negative (-) wire to the - speaker
terminal as shown in step below.9b
c. Proceed to step .10
9. See the following block diagram.
a. Route the wires from the amplier to the speaker using the same procedure for routing speaker wire (and conduit if
applicable) through the transformer cover plate as described in steps through (see the wire gauge table on page 4 7b
1). Strip 3/16 inch (5 mm) from the ends of the two speaker wire leads (+ and -) coming from the amplier. Keep the wire
strands together by twisting them (do not tin the wires), and secure the wires to the input terminals of the speaker while
observing the correct polarity.
Direct Connection
(bypassing the transformer)
Amplifier
Transformer
FF 120T
b. Connect the red positive (+) wire to the + speaker terminal and connect the black negative (-) wire to the - speaker
terminal, depending on whether one or two speakers are being connected, as shown below.
Red Wire
Bla ireck W
From Amplifier
One Speaker
From Amplifier
Red Wire
Black Wire
To Second Spea rke
From Amplifier
To Second Spea rke
Two Speakers
10. Replace the transformer cover plate and tighten the two cover plate screws that were loosened in step .4
NC
1 W
2 W4 W16 WCOM
70 V
100 V
COM NC 16 W 8 W 4 W 2 W 1 W
8 W
Wiring to a Single Speaker
NC
1 W
2 W4 W16 WCOM
70 V
100 V
COM NC 16 W 8 W 4 W 2 W 1 W
8 W
Red Wires
Black Wires From Amplifier (+)
To Next Speaker (tap)
From Amplifier (-)
To Next Speaker (com)
Tuotetiedot
| Merkki: | Extron |
| Kategoria: | Kaiutin |
| Malli: | FF 120T |
Tarvitsetko apua?
Jos tarvitset apua merkille Extron FF 120T esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Kaiutin Extron Käyttöohjeet
12 Maaliskuuta 2025
23 Joulukuuta 2024
16 Lokakuuta 2024
15 Lokakuuta 2024
15 Lokakuuta 2024
15 Lokakuuta 2024
15 Lokakuuta 2024
15 Lokakuuta 2024
15 Lokakuuta 2024
15 Lokakuuta 2024
Kaiutin Käyttöohjeet
- Kaiutin Aiwa
- Kaiutin Bauhn
- Kaiutin Insignia
- Kaiutin LG
- Kaiutin Power Dynamics
- Kaiutin Vonyx
- Kaiutin Grundig
- Kaiutin Sharp
- Kaiutin Hama
- Kaiutin Vorago
- Kaiutin Jensen
- Kaiutin AOC
- Kaiutin Philips
- Kaiutin Avantree
- Kaiutin IKEA
- Kaiutin Edifier
- Kaiutin Reflexion
- Kaiutin Meridian
- Kaiutin Teufel
- Kaiutin Fender
- Kaiutin Axton
- Kaiutin Kogan
- Kaiutin Soundcore
- Kaiutin Turbosound
- Kaiutin Sony
- Kaiutin GoGEN
- Kaiutin Pro-Ject
- Kaiutin Yamaha
- Kaiutin Xiaomi
- Kaiutin Morel
- Kaiutin Trust
- Kaiutin Axis
- Kaiutin Media-tech
- Kaiutin Pioneer
- Kaiutin EarFun
- Kaiutin Ecler
- Kaiutin Audac
- Kaiutin Woxter
- Kaiutin KEF
- Kaiutin Audio-Technica
- Kaiutin Toa
- Kaiutin Metra
- Kaiutin Pyle
- Kaiutin Sencor
- Kaiutin Bose
- Kaiutin Orava
- Kaiutin Kanto
- Kaiutin Wet Sounds
- Kaiutin JVC
- Kaiutin Sharper Image
- Kaiutin Kicker
- Kaiutin Auna
- Kaiutin OSD Audio
- Kaiutin Fenton
- Kaiutin Bluesound
- Kaiutin Hertz
- Kaiutin Kenwood
- Kaiutin MB Quart
- Kaiutin Bigben
- Kaiutin Aplic
- Kaiutin CSL
- Kaiutin Bearware
- Kaiutin NUVO
- Kaiutin Infiniton
- Kaiutin Sennheiser
- Kaiutin Roku
- Kaiutin GPO
- Kaiutin Advance
- Kaiutin Sonance
- Kaiutin AXESS
- Kaiutin Artsound
- Kaiutin Denon
- Kaiutin Ion
- Kaiutin Elac
- Kaiutin Marshall
- Kaiutin Yorkville
- Kaiutin V-Tac
- Kaiutin MyDJ
- Kaiutin Braun
- Kaiutin Valcom
- Kaiutin Celly
- Kaiutin JBL
- Kaiutin Infinity
- Kaiutin Majority
- Kaiutin Helix
- Kaiutin Genesis
- Kaiutin Logilink
- Kaiutin Klipsch
- Kaiutin Worx
- Kaiutin Muse
- Kaiutin Ground Zero
- Kaiutin Karma
- Kaiutin Glemm
- Kaiutin Prixton
- Kaiutin Match
- Kaiutin Speed-Link
- Kaiutin Renkforce
- Kaiutin Definitive Technology
- Kaiutin QSC
- Kaiutin WHD
- Kaiutin Q Acoustics
- Kaiutin Karcher
- Kaiutin GoldenEar
- Kaiutin Pyramid
- Kaiutin FoneStar
- Kaiutin Apogee
- Kaiutin Trevi
- Kaiutin Monitor Audio
- Kaiutin Peavey
- Kaiutin Canton
- Kaiutin Fresh N Rebel
- Kaiutin Sven
- Kaiutin Craftsman
- Kaiutin Energy Sistem
- Kaiutin PSB
- Kaiutin Vizio
- Kaiutin Polk
- Kaiutin ESX
- Kaiutin Omnitronic
- Kaiutin Crestron
- Kaiutin Russound
- Kaiutin MEE Audio
- Kaiutin Monacor
- Kaiutin ModeCom
- Kaiutin Hercules
- Kaiutin Black Hydra
- Kaiutin Electro-Voice
- Kaiutin Proscan
- Kaiutin Wharfedale
- Kaiutin Monster
- Kaiutin Boss
- Kaiutin Tannoy
- Kaiutin JL Audio
- Kaiutin Atlas Sound
- Kaiutin Davis
- Kaiutin Mount-It!
- Kaiutin GMB Audio
- Kaiutin Mad Dog
- Kaiutin Ashly
- Kaiutin Origin Acoustics
- Kaiutin VTech
- Kaiutin Samson
- Kaiutin Memphis Audio
- Kaiutin Focal
- Kaiutin Alpine
- Kaiutin Boompods
- Kaiutin Kramer
- Kaiutin Genelec
- Kaiutin Bazooka
- Kaiutin KRK
- Kaiutin Lamax
- Kaiutin NGS
- Kaiutin Aiaiai
- Kaiutin RCF
- Kaiutin SVS
- Kaiutin N-Gear
- Kaiutin Vimar
- Kaiutin Phoenix Gold
- Kaiutin Aconatic
- Kaiutin Bogen
- Kaiutin Atlas
- Kaiutin PowerBass
- Kaiutin Manta
- Kaiutin Trendnet
- Kaiutin Prime3
- Kaiutin Duronic
- Kaiutin Harman Kardon
- Kaiutin Yamazen
- Kaiutin Lexibook
- Kaiutin Ibiza Sound
- Kaiutin Creative
- Kaiutin REL Acoustics
- Kaiutin Savio
- Kaiutin House Of Marley
- Kaiutin Klark Teknik
- Kaiutin Phonic
- Kaiutin Crosley
- Kaiutin Imperial
- Kaiutin BlueAnt
- Kaiutin Lexon
- Kaiutin Apart
- Kaiutin Magnat
- Kaiutin Hifonics
- Kaiutin Boston Acoustics
- Kaiutin Crest Audio
- Kaiutin Devialet
- Kaiutin AudioSource
- Kaiutin Taga Harmony
- Kaiutin SoundTube
- Kaiutin James
- Kaiutin Ruark Audio
- Kaiutin MB
- Kaiutin Antelope
- Kaiutin Lenco
- Kaiutin M-Audio
- Kaiutin Heco
- Kaiutin SureFire
- Kaiutin Dali
- Kaiutin Akai
- Kaiutin Metronic
- Kaiutin Berker
- Kaiutin LD Systems
- Kaiutin Xcellon
- Kaiutin Denon DJ
- Kaiutin Nikkei
- Kaiutin HK Audio
- Kaiutin Eve Audio
- Kaiutin Delvcam
- Kaiutin Grimm Audio
- Kaiutin Elbe
- Kaiutin DAP Audio
- Kaiutin Deaf Bonce
- Kaiutin Defender
- Kaiutin Adam
- Kaiutin Cerwin-Vega
- Kaiutin Ikegami
- Kaiutin Revel
- Kaiutin New One
- Kaiutin Mission
- Kaiutin Alto
- Kaiutin Califone
- Kaiutin Martin Logan
- Kaiutin Tangent
- Kaiutin Dynaudio
- Kaiutin Proel
- Kaiutin Mackie
- Kaiutin Bowers Wilkins
- Kaiutin Audibax
- Kaiutin PreSonus
- Kaiutin Dual
- Kaiutin Sonus Faber
- Kaiutin Magnavox
- Kaiutin OWI
- Kaiutin Fusion
- Kaiutin Titanwolf
- Kaiutin Weather X
- Kaiutin Krüger And Matz
- Kaiutin Indiana Line
- Kaiutin Blue Tees
- Kaiutin BASSBOSS
- Kaiutin Exagerate
- Kaiutin Ikarao
- Kaiutin FBT
- Kaiutin Transparent
- Kaiutin IHome
- Kaiutin Andover
- Kaiutin ILive
- Kaiutin Moonki
- Kaiutin Urban Revolt
- Kaiutin Audison
- Kaiutin Boynq
- Kaiutin Clarity
- Kaiutin VIETA PRO
- Kaiutin Potter
- Kaiutin Sonoro
- Kaiutin Nubert
- Kaiutin Amphion
- Kaiutin Naxa
- Kaiutin Induction Dynamics
- Kaiutin Paradigm
- Kaiutin Cyber Acoustics
- Kaiutin Audio Pro
- Kaiutin IPort
- Kaiutin ETON
- Kaiutin Ultimate Ears
- Kaiutin NEAR
- Kaiutin Irradio
- Kaiutin Rockustics
- Kaiutin Louroe Electronics
- Kaiutin Kalley
- Kaiutin MOOOV
- Kaiutin Elipson
- Kaiutin SOUNDBOKS
- Kaiutin Streetz
Viimeisimmät Kaiutin Käyttöohjeet
8 Huhtikuuta 2025
8 Huhtikuuta 2025
8 Huhtikuuta 2025
7 Huhtikuuta 2025
7 Huhtikuuta 2025
7 Huhtikuuta 2025
5 Huhtikuuta 2025
3 Huhtikuuta 2025
3 Huhtikuuta 2025
3 Huhtikuuta 2025