Glide Gear POV100 Käyttöohje
Glide Gear
Kolmijalka
POV100
Lue alta 📖 käyttöohje suomeksi merkille Glide Gear POV100 (3 sivua) kategoriassa Kolmijalka. Tämä opas oli hyödyllinen 3 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/3
POV 100
1 PLEASE NOTE:
For use with cameras weighing up to 2.5lbs or
1.15kg including the lens
The POV100 comes in 2 sizes: M (54 60cm/21.25- -
23.6”) and L (56 62cm/22 24.4- - ”)
Recommended use with wide angle lenses set to
innity focus for best results
For more informaon please visit our website: www.glidegear.net
2
Fig A
4
Mount your camera using the screw
inside the slot in the crossbar in the
front of the helmet. See Fig A.
Crossbar
Mounng
screw
3 Included with the POV 100 are 10 weight plates. With
the camera mounted in the front, your head will be
leaning forward. Add weight plates to the back of the
helmet to balance your head and ease the strain on
your neck. Use the supplied thumb nut to secure the
weight plates in an unloose posion. See Fig. B
Fig C
Hint: Weigh your camera and use the appropriate
number of plates to get as close as possible to the
camera weight knowing that 1 plate weighs about
4oz (or 100g).
Example: For a camera weighing 1.6lbs, add 6-7
plates to the back.
Thumb nut
In the rear inside of the helmet, you will nd a knob.
Use the knob to ghten or loosen the helmet s inside ’
frame so that the helmet ts ghtly on your head.
The knob in queson is circled on Fig. C.
Fig B
POV 100
5
Top Plate features:
1/4 20 female threaded holes to mount mic, lights, fricon arm etc..-
14/4 20 mounng screw to mount a GoPro, a 360 camera, light, mic, fricon -
arm etc..
For more informaon please visit our website: www.glidegear.net
Fig D
At this point, your setup should look like Fig. D. The POV 100 is a very exible head rig with mulple
adjustments and mounng possibilies. See the adjustments available below .
Front Plate features:
1/4 20 female threaded holes -
for accessories
14/4 20 mounng screw-
Crossbar Knobs:
Loosen up the knobs. Adjust the
angle of the camera. Tighten the
knobs when done.
Temple Plate:
Remove the 2 screws. While
keeping a 45 degree angle, move
the camera frame horizontally
and along the slot to adjust how
far from the face the camera will
be.
Lock in place using the 2 screws.
Use the other threaded holes to
mount accessories.
Mid –secon Knobs:
Loosen up the knobs. Adjust
the camera posion so you
can see clearly in front of
you. Tighten the knobs when
done.
POV 100
For more informaon please visit our website: www.glidegear.net
If any assembling is needed, please refer to the below secon:
BACK: Mount the plate with the longest
screw to the back of the helmet using 2 of the
supplied M3 screws. Fig E.
FRONT: Mount the curved rectangular plate
to the front of the helmet using 2 of the sup-
plied M3 screws and through the 2 slots on
the plate. Fig F.
SIDES: Mount the 2 idencal plates to the sides
of the helmet using 2 of the supplied M3 screws
and through the 2 slots on the plate. Each plate
should be oriented so that the plate s thicker end ’
faces the back of the helmet . Fig. H.
TOP: Mount the rectangular at plate to the
top of the helmet using 2 of the supplied M3
screws and through the 2 slots on the plate.
Fig G.
Thinner end
Thicker end
Fig F
Fig E
Fig G
Fig H
Tuotetiedot
| Merkki: | Glide Gear |
| Kategoria: | Kolmijalka |
| Malli: | POV100 |
Tarvitsetko apua?
Jos tarvitset apua merkille Glide Gear POV100 esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Kolmijalka Glide Gear Käyttöohjeet
27 Lokakuuta 2024
16 Lokakuuta 2024
Kolmijalka Käyttöohjeet
- Kolmijalka Neewer
- Kolmijalka Kogan
- Kolmijalka Manfrotto
- Kolmijalka Celly
- Kolmijalka Square Jellyfish
- Kolmijalka Proaim
- Kolmijalka Libec
- Kolmijalka Gravity
- Kolmijalka Celestron
- Kolmijalka Vanguard
- Kolmijalka Vinten
- Kolmijalka Stalco
- Kolmijalka SteadiCam
- Kolmijalka Fidlock
Viimeisimmät Kolmijalka Käyttöohjeet
27 Lokakuuta 2024
26 Lokakuuta 2024
25 Lokakuuta 2024
21 Lokakuuta 2024
21 Lokakuuta 2024
21 Lokakuuta 2024
21 Lokakuuta 2024
21 Lokakuuta 2024
21 Lokakuuta 2024
21 Lokakuuta 2024