Hobart 403 Käyttöohje
Lue alta 📖 käyttöohje suomeksi merkille Hobart 403 (8 sivua) kategoriassa Lihamylly. Tämä opas oli hyödyllinen 2 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/8
701 S. RIDGE AVENUE
TROY, OHIO 45373
937 332-3000
www.hobartcorp.com
MODEL 403 TENDERIZER
ML-38763 403
FORM 37023 Rev A. (August 2024)
– 2 –
Installation, Operation and Care of
MODEL 403 TENDERIZER
SAVE THESE INSTRUCTIONS
GENERAL
The model 403 Tenderizer is designed to tenderize a variety of meat products. The tenderizer consists
of a set of roller units which contain knives that knit together and tenderize pieces of meat as they pass
through the blades. Optional Wide 3/8" or Narrow 3/16" Julienne Knife Lift-out units are available. They are
used to cut food products, such as meats and cheeses, into strips.
INSTALLATION
UNPACKING
Immediately after unpacking, check for possible shipping damage. If the tenderizer is found to be damaged,
save the packaging material and contact the carrier within 5 days of delivery.
Remove machine from the shipping carton and place in the operating location. Remove transparent guard
(4, Fig. 1), lift off motor housing (3, Fig. 1) and remove screw (1, Fig. 2) that plugs the vent hole (see label
taped to machine). Insert dip stick (taped to machine) in vent hole. Replace housing and guard.
A cord with plug is furnished as standard equipment.
Before making electrical connections, check the specications on the machine data plate to ensure they
agree with those of your electrical service.
This machine must be cleaned after installation and before being put into service. Refer to MAINTENANCE
for instructions.
© HOBART, 2024
Fig. 1
– 3 –
SAFETY
Safety devices incorporated in this machine MUST be in correct operating position anytime this machine
is in service. Both the transparent guard and the motor housing must be in place. The pilot light (2, Fig. 1)
will remain on when either the transparent guard or motor housing is removed and the switch is on. Motor
will start when the guard and housing have been replaced. DO NOT defeat any of the safety features.
OPERATION
Turn the switch (1, Fig. 1) to ON. The pilot light (2, Fig. 1) will illuminate indicating power is supplied to
the machine.
To tenderize meats, simply drop cuts into the top of transparent guard and receive them at the bottom.
Only boneless meats should be used. Choice or tender cuts should be run through several times at
different angles. Less tender cuts should be run through several more times at different angles to increase
tenderness. Pull out excess sinews to improve tenderness.
Various combinations of different meat types may be blended together. This is accomplished by running
the meat types through separately to tenderize, then together creating a rmly knit cut. Large slices should
be under 3/ " thick.4
MAINTENANCE
Unplug machine power cord before beginning any maintenance procedure.
Tuotetiedot
| Merkki: | Hobart |
| Kategoria: | Lihamylly |
| Malli: | 403 |
Tarvitsetko apua?
Jos tarvitset apua merkille Hobart 403 esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Lihamylly Hobart Käyttöohjeet
7 Maaliskuuta 2025
Lihamylly Käyttöohjeet
- Lihamylly Royal Catering
- Lihamylly Bartscher
- Lihamylly Philips
- Lihamylly Gorenje
- Lihamylly Panasonic
- Lihamylly RGV
- Lihamylly Scarlett
- Lihamylly Eldom
- Lihamylly Weston
- Lihamylly Ade
- Lihamylly Ardes
- Lihamylly Zelmer
- Lihamylly Catler
Viimeisimmät Lihamylly Käyttöohjeet
13 Tammikuuta 2025
10 Tammikuuta 2025
2 Tammikuuta 2025
1 Tammikuuta 2025
29 Joulukuuta 2024
16 Joulukuuta 2024
10 Joulukuuta 2024
10 Joulukuuta 2024
9 Joulukuuta 2024
7 Joulukuuta 2024