Infratech 21-5080 Käyttöohje
Lue alta 📖 käyttöohje suomeksi merkille Infratech 21-5080 (8 sivua) kategoriassa Lämmitin. Tämä opas oli hyödyllinen 4 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/8
TABLE OF CONTEN
RE MANUAL
Warnings
Installation Instructio
Wiring Instructions 3
Bracket Spacing 4
Mounting Instructions 4-5
Replacement Element Installation 5
Replacement Parts 5-6
Heater Coverage Areas 6
General Notes 6
Maintenance Instructions 6
Trouble Shooting 7
Location Suggestions 7
Warranty 8
SAVE THIS MANUAL FOR FUTURE REFERENCE
2
MIN. 18" (45.7cm)
FROM SIDES AND
ENDS OF HEATER
MIN. 36" (91.4cm)
IN FRONT OF HEATER
MIN. 6" (15.2cm)
CLEARANCE
BEHIND HEATER
READ ALL INSTRUCTIONS BEFORE USING HEATER. Unit may be a source of possible shock. NEVER attempt to
service heater without disconnecting its power source. Source of possible ignition.
WARNING: If not installed, operated and maintained in accordance with the manufacturer’s instructions,
this product can expose you to chemicals including nickel, which are known to the State of California to
cause cancer. For more information go to www.P65Warnings.ca.gov.
High Temperature, risk of fire, keep electrical cords, drapery, furnishings and other combustibles at least 3' (0.9m)
from the front of heater and away from sides and rear.
WARNINGS
CAUTION
MOUNTING HEIGHT/CLEARANCES
“IMPORTANT INSTRUCTIONS”
“SAVE THESE INSTRUCTIONS”
• For Wall-Mounting, do not install heater closer than
18" (45.7cm) from adjacent walls and 6" (15.2cm)
from ceiling and do not install less than 6' (1.8m)
if the heater is labeled as UL Listed and 8' (2.4m)
if the heater is labeled as UL/CUL Listed from floor,
while heater is set at a downward angle of 30 to
60 degrees.
• For Ceiling- Mounting, do not install heater closer
than 18" (45.7cm) from adjacent walls and 6"
(15.2cm) from ceiling and do not install less than 6'
(1.8m) if the heater is labeled as UL Listed and 8'
(2.4m) if the heater is labeled as UL/CUL Listed from
floor, while heater is at a maximum 30 degrees.
• Adjacent Heaters to be installed no less than 3'
(0.9m) apart.
• Do NOT operate within 25' (7.6m) of flammable/
explosive material.
• Never block heater.
• Heaters greater than 240 Volts are for “Commercial
Use Only. Risk of fire. Do not use as a residential or
household heater.”
• A means for disconnection of the appliance must
be incorporated in accordance with the local wiring
codes.
• Do not use if the heating element is damaged or
cracked.
• Not for use as a replacement for forced air/
ductless heating.
• Do not leave powered heaters unattended.
• Do not run heaters for more than 4 hours at a time
without a 15-minute cool down period between uses.
INSTALLATION INSTRUCTIONS
This heater must be permanently installed and hard wired by a licensed electrician in accordance with local electrical
codes. Assembly procedure must be performed with no electrical power to unit.
Step 1: Check UL/CUL/CE label on heater for proper voltage.
Step 2: Follow supplied wiring instructions (see wiring instructions below).
Step 3: Heater must be mounted with reflector angled down.
Step 4: All electrical connections must be in compliance with the National Electric Code (NEC) and local codes for
outdoor wiring.
Step 5: Use only wiring components UL/CUL/CE listed for outdoor use with IPX4 minimum rating.
3
1/2" NPT
If rotation is required,
push in the spring pin
located on the back
side of the heater
trim to disengage the
two pins from their
alignment hole and
rotate 180º.
Connect power with flexible
conduit or appropriate cord to
allow heater to be swiveled.
WIRING INSTRUCTIONS
The heater is drilled and threaded for standard 1/2" conduit fittings. The installing electrician will need to provide the
appropriate rigid metallic, flexible or liquid tight conduit for the installation location.
• Use only copper wire suitable for 90°C.
• Observe local electrical code regulations.
"T" slot allows the
mounting bracket
to slide for flexible
mounting options.
Logo plate (designed
to rotate if required).
TYPICAL WIRING OPTIONS
HEATING ELEMENT
OFF
ON
OFF
ON
HEATER
TOP
P L1 L2
H2H1
HEATER
FOR 115V. PILOT
LIGHT IF USED
REAR VIEW OF
CONTROLLER FOR
MAX. 15 AMP
LOAD ONLY
"TOP" MARKED ON
REAR OF CONTROL
MUST BE INSTALLED
IN AN UP POSITION
240 V.
240 V.
WHITE
BLACK 115 V.
TYPICAL 120V WIRING
FOR A SINGLE POLE SWITCH
TYPICAL 240V WIRING FOR
A TWO POLE SWITCH
WIRING FOR OPTIONAL 120V/240V CONTROLS
Tuotetiedot
| Merkki: | Infratech |
| Kategoria: | Lämmitin |
| Malli: | 21-5080 |
Tarvitsetko apua?
Jos tarvitset apua merkille Infratech 21-5080 esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Lämmitin Infratech Käyttöohjeet
5 Joulukuuta 2024
Lämmitin Käyttöohjeet
- Lämmitin NewAir
- Lämmitin Adler
- Lämmitin Electrolux
- Lämmitin AEG
- Lämmitin Delonghi
- Lämmitin Kogan
- Lämmitin Create
- Lämmitin Candy
- Lämmitin Sencor
- Lämmitin Orava
- Lämmitin Fluval
- Lämmitin Gude
- Lämmitin Brandson
- Lämmitin Ausclimate
- Lämmitin Ufesa
- Lämmitin Master
- Lämmitin Einhell
- Lämmitin Dometic
- Lämmitin Eldom
- Lämmitin Brentwood
- Lämmitin Korona
- Lämmitin Stanley
- Lämmitin Big Ass Fans
- Lämmitin Bionaire
- Lämmitin Herschel
- Lämmitin AustWood
- Lämmitin Mellerware
- Lämmitin Otsein-Hoover
- Lämmitin Perfect Aire
- Lämmitin LifeSmart
- Lämmitin EvoHeat
- Lämmitin Broan
- Lämmitin Yamazen
- Lämmitin Eurom
- Lämmitin Ravanson
- Lämmitin Eurotronic
- Lämmitin TANSUN
- Lämmitin Astralpool
- Lämmitin Global
Viimeisimmät Lämmitin Käyttöohjeet
20 Joulukuuta 2024
20 Joulukuuta 2024
19 Joulukuuta 2024
19 Joulukuuta 2024
18 Joulukuuta 2024
18 Joulukuuta 2024
18 Joulukuuta 2024
18 Joulukuuta 2024
18 Joulukuuta 2024
18 Joulukuuta 2024