Jilong JL027266NG Käyttöohje
Lue alta 📖 käyttöohje suomeksi merkille Jilong JL027266NG (34 sivua) kategoriassa ilmapatja. Tämä opas oli hyödyllinen 3 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/34
1
Important Safety Guideline
Please read, understand and follow all instructions prior to using.
To enhance the enjoyment of your Air Bed and protect the safety of the operator
using the product, ALWAYS STRICTLY OBSERVE the following important
safety points. The following important points should be read and understand before
using this product:
1. : To prevent possible electric shock, do not attempt to plug in power WARNING
cord with wet hands.
2. : To prevent possible electric shock, connect power cord into a WARNING
grounded receptacle protected by a ground-fault circuit interrupter (GFCI).
3. : To prevent possible electric shock, never use a damaged or frayed WARNING
power cord. If the supply cord is damaged, it must be replaced by the
manufactured or its service agent or a similarly qualified person in order to avoid
a hazard.
4. : Do not extension power cords with this product. WARNING
5. Only for indoor household use. Keep away from fire. WARNING:
6. In order to reduce the risk of electric shock, do not expose to rain. WARNING:
And store indoors.
7. RISK OF COMBUSTION: Do not place the airbed against or near any open
flames, heaters, furnaces or other hot objects.
8. IMPORTANT: Do not operate electric pump for more than 5 minutes at one
time (Generally, 5 minutes for each inflation or deflation is enough), take 20
minutes break between uses, as overheating may occur and pump will
automatically shut off. It will be ready to use after it has cooled down. This
automatic shut off is for your safety. Unplug electrical power cord when not in
use.
9. Do not obstruct the air passage opening or insert any objects into WARNING:
the opening at any time.
10. Do not stand, jump or use the airbed as a trampoline. Always WARNING:
supervise children near the airbed.
11. This product is not a raft or floatation device. Do not use near or WARNING:
on water.
12. Children must not be left unattended when using the airbed. Use WARNING:
only under adult competent supervision.
13. : The storage bag is not a toy. To avoid danger of suffocation, keep WARNING
the airbed storage bag or any other bags away from babies and children. Fold up
the bag and store away from children when not in use.
14. : Keep pets away from the airbed. Pets may tear or puncture the WARNING
airbed.
15. IMPORTANT: Make sure the area is flat, smooth, even and free of sharp
IPN2-13-E
Instruction Manual
Built-in Electric Pump
220 240V ~ 50 Hz 13 –0W
2
objects that can puncture the airbed. Do not set up the airbed nearby stairs, doors,
drops, sharp edges or breakables.
16. IMPORTANT: To minimize any chance of rolling, tipping or swaying, avoid
sleeping on the edge of the airbed. Edges provide less support than the middle of
the airbed.
17. IMPORTANT: This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their
safety.
18. IMPORTANT: Children should be supervised to ensure that they do not play
with the appliance.
Inflation instructions
1. Open the cord cover of pump first and make sure the optional inflation air valve is
securely closed.
2. Plug the AC electrical line cord into an AC electrical outlet (ground fault circuit
interrupter outlet). Please check the correct voltage! See Fig. (1)
3. Turn the control dial clockwise until the inflation mark ( ). arrow points to
See Fig. (2)
220 240V –
11 0 –120V
Fig.(1)
×
×
×
××
√
√
√
√√
Fig.(2)
3
4. When the airbed is fully inflated to the desired firmness, turn the control dial
counter-clockwise until arrow points to the “OFF”. See Fig. (3)
5. Lie down on the airbed to test the firmness.
6. If the sleeping surface is too hard, adjust the firmness by continuously turning the
control dial counter-clockwise gradually until air start to exit through the air
passage. Then turn the control dial clockwise until arrow points to the “ ”OFF
when the desired firmness is achieved. If the airbed becomes too soft, please repeat
step 3 thru 5 as necessary.
7. Disconnect the AC line cord from the wall socket and place it inside the cord
compartment.
Deflation instructions
1. Open the cord cover of pump first and make sure the optional inflation air valve is
securely closed.
2. Plug the AC electrical line cord into an AC electrical outlet (ground fault circuit
interrupter outlet). Please check the correct voltage! See Fig. (1)
3. Turn the control dial counter-clockwise until arrow points to the deflation mark
( ). See below Fig. (4)
4. When all air is removed from the airbed, turn the control dial clockwise until
arrow points to the . See below Fig. (3) “ ”OFF
5. When the airbed is completely deflated, begin rolling the airbed from the foot of
the airbed towards the head of the airbed where the pump is located. To ensure the
airbed is fully deflated, repeat steps 3 thru 4.
Fig.(3)
Tuotetiedot
| Merkki: | Jilong |
| Kategoria: | ilmapatja |
| Malli: | JL027266NG |
Tarvitsetko apua?
Jos tarvitset apua merkille Jilong JL027266NG esitä kysymys alla ja muut käyttäjät vastaavat sinulle
ilmapatja Jilong Käyttöohjeet
18 Lokakuuta 2024
18 Lokakuuta 2024
18 Lokakuuta 2024
18 Lokakuuta 2024
ilmapatja Käyttöohjeet
Viimeisimmät ilmapatja Käyttöohjeet
26 Lokakuuta 2024
26 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024