Luxul Apex XAP-1610 Käyttöohje
Lue alta 📖 käyttöohje suomeksi merkille Luxul Apex XAP-1610 (8 sivua) kategoriassa Tukiasema. Tämä opas oli hyödyllinen 2 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/8
READ ME FIRST
QUICK INSTALL GUIDE
Apex
Wave 2 AC3100 Dual-Band Wireless
Access Point
XAP-1610
Includes:
Wave 2 AC3100 Dual-Band Wireless AP
Mounting Brackets and Hardware
PoE Injector and Power Adapter
Ethernet Cables
™
READ ME FIRST - CONTROLLER COMPATIBILITY
This XAP-1610 is compatible with the Luxul Wireless Controller for fast, easy
configuration and deployment of wireless networks with multiple APs.
nNote: If you’ll be using this AP with a Wireless Controller, refer to
the Quick Install Guide included with the Wireless Controller for
setup instructions.
nNote: Please check to make sure this AP is running the latest version of
firmware (as indicated at https://www.luxul.com/firmware-updates.
aspx) before continuing onto the next steps.
AP SETUP AND CONFIGURATION
1 Physical Installation
The XAP-1610 access point is designed for simple and ecient installation and
can be located one of three ways. First, the included mount is designed to
attach directly to several dierent regions’ standard electrical boxes. Second,
the XAP-1610 may be mounted on a ceiling or wall without a box by using the
included mount as a guide to mark attachment locations. Finally, the XAP-1610
can be placed on a flat surface by attaching the included rubber feet
to the mount.
cCaution: Attach the rubber feet to the mount and attach the mount to
the AP for flat surface placement to avoid overheating and failure.
XSingle Access Point Placement: Because the signal generated by the
XAP-1610 is omnidirectional, the unit should be located as near as possible
to the center of the desired coverage area.
XAP-1610 Single AP Coverage Pattern
XMultiple Access Point Placement: You may need to experiment with
AP placement to optimize the roaming experience. Place APs to ensure
adequate coverage, but not so far apart that there is no signal overlap.
Adjacent APs should overlap enough that the client device has a good
connection to the AP to which it is currently attached, but also sees the
next-nearest AP. Ideally, roaming clients should see signal strength of
two overlapping APs in the range of -60 to -70 dBm at the midway
point between two APs. To learn more about AP placement, visit
luxul.com/ap-placement.
XAP-1610 Multiple AP Coverage and Overlap
nNote: Consider using Ekahau HeatMapper to assist with this process,
available from www.ekahau.com. Luxul also oers an informative
“How-To” video on HeatMapper at luxul.com/how-to-videos.
Tuotetiedot
| Merkki: | Luxul |
| Kategoria: | Tukiasema |
| Malli: | Apex XAP-1610 |
Tarvitsetko apua?
Jos tarvitset apua merkille Luxul Apex XAP-1610 esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Tukiasema Luxul Käyttöohjeet
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
Tukiasema Käyttöohjeet
Viimeisimmät Tukiasema Käyttöohjeet
16 Lokakuuta 2024
15 Lokakuuta 2024
15 Lokakuuta 2024
15 Lokakuuta 2024
15 Lokakuuta 2024
15 Lokakuuta 2024