Luxul XAP-1240 Käyttöohje
Lue alta 📖 käyttöohje suomeksi merkille Luxul XAP-1240 (8 sivua) kategoriassa Tukiasema. Tämä opas oli hyödyllinen 2 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä
Sivu 1/8
READ ME FIRST
QUICK INSTALL GUIDE
High Power Wireless 300N
Outdoor Access Point
XAP-1240
Includes:
One: XAP-1240 Wireless Access Point
One: PoE Injector and Power Cord
One: Ethernet Cable
Two: Cable Ties
READ ME FIRST - AP COMPATIBILITY
This XAP-1240 is compatible with the Luxul XWC-1000 Wireless Controller for
fast, easy configuration and deployment of wireless networks with multiple APs.
nNote: If you’ll be using this AP with a Wireless Controller, refer to
the Quick Install Guide included with the Wireless Controller for
setup instructions.
If you’re using separately-purchased Luxul APs or installing this AP along
with a Wireless Controller in an existing Luxul deployment, you may
need to manually upgrade firmware for some of those APs before installing
the Wireless Controller.
Luxul APs running firmware version 5 or later (like the one in
this package) are Wireless Controller-compatible and can
be used with the Controller as-is. When purchasing Luxul
APs for use with the Wireless Controller, look for an orange
“Version 5 Firmware” sticker on the box to avoid the manual
upgrade process.
nNote: Visit http://luxul.com/ap-upgrade for help upgrading your AP’s
firmware to version 5 or newer.
AP SETUP AND CONFIGURATION
1 Physical Installation
The XAP-1240 access point is designed for simple and efficient installation.
Four keyholes allow for easy wall-mounting, or for mounting to a pole, use the
included cable ties (zip ties) to secure the AP to the pole. Loosely secure two
cable ties, one through each mounting flange slot, then tighten the cable ties.
C
O
N
T
R
O
L
L
E
R
R
E
A
D
Y
•
C
O
N
T
R
O
L
L
E
R
R
E
A
D
Y
•
VERSION
5
FIRM WARE
XSingle Access Point Placement: Because the signal generated by the
XAP-1240 is directional, the unit should be located at the perimeter
of the desired coverage area, with the large flat surface aimed toward
the center.
XAP-1240 Single AP Coverage Pattern
XMultiple Access Point Placement: You may need to experiment with
AP placement to optimize the roaming experience. Place APs to ensure
adequate coverage, but not so far apart that there is no signal overlap.
Adjacent APs should overlap enough that the client device has a good
connection to the AP to which it is currently attached, but also sees the
next-nearest AP. Ideally, roaming clients should see signal strength of
two overlapping APs in the range of -60 to -70 dBm at the midway
point between two APs. To learn more about AP placement, visit
luxul.com/ap-placement.
Ideally, roaming clients should see
signal strength of two overlapping
APs in the range of -60 to -70 dBm a
the midway point between two APs
XAP-1240 Multiple AP Coverage and Overlap
nNote: Consider using Ekahau HeatMapper to assist with this process,
available from www.ekahau.com. Luxul also offers an informative
“How-To” video on HeatMapper at luxul.com/how-to-videos.
Tuotetiedot
| Merkki: | Luxul |
| Kategoria: | Tukiasema |
| Malli: | XAP-1240 |
Tarvitsetko apua?
Jos tarvitset apua merkille Luxul XAP-1240 esitä kysymys alla ja muut käyttäjät vastaavat sinulle
Tukiasema Luxul Käyttöohjeet
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
16 Lokakuuta 2024
Tukiasema Käyttöohjeet
Viimeisimmät Tukiasema Käyttöohjeet
16 Lokakuuta 2024
15 Lokakuuta 2024
15 Lokakuuta 2024
15 Lokakuuta 2024
15 Lokakuuta 2024
15 Lokakuuta 2024