MB Quart FA2-400.4 Käyttöohje

MB Quart Vastaanotin FA2-400.4

Lue alta 📖 käyttöohje suomeksi merkille MB Quart FA2-400.4 (2 sivua) kategoriassa Vastaanotin. Tämä opas oli hyödyllinen 4 henkilölle ja sai 4.5 tähden keskimäärin 2 käyttäjältä

Lataa PDF
Sivu 1/2
External 40A
External 100A
External 80A
External 100A
External 125A
Place terminal in a secure
position so that it won’t
accidentally contact the
negative battery post
Power cable size
and fusing
It is critical to use the proper power
and ground cable. Select the size
listed here for your amplier model.
Always use high quality copper
cable. Visit our website for multi amp
system cable recommendations.
Be sure to use the proper fuse size
for each model.
Properly route power,
speaker and RCA cables
through the vehicle.
Choose a mounting location
that will provide adequate air
ventilation. Mount the amplier to
a secure surface. Do not mount
the amplier upside down.
Attach the chassis ground
cable to the amplier
negative terminal. It is
important to make sure this
connection is very tight.
Bare metal
Attach the main power cable
to the amplier +12V. The
cable must run directly to
the battery and be properly
fused and be very tight.
Attach the remote turn on
wire to the amplier remote
output of the source unit.
Connect the RCA cables to the
coordinating RCA input number
that will match the speaker
outputs number.
Connect the power cable to the
positive battery terminal. The
power cable must be fused
within 18 inches of the battery
terminal.
Re-connect the negative
battery terminal making sure it
is securely tightened.
The chassis ground connection
is critical to the performance
of the amplier. Choose a
location that is close to the
amplier. Completely scrape
away the paint and use a nut
and bolt if possible.
DO NOT USE AN EXISTING
FACTORY BOLT!
Disconnect
negative battery
terminal
Run Cables
Mount Amplier
Negative Power
Connection
Positive Power
Connection
Remote Turn-on
Connection
Signal Input
Connection
Positive Battery
Connection
Re-connect
Negative Battery
Terminal
Chassis Ground
Be prepared to disarm your vehicle’s alarm and
to enter your radio / source unit code.
Installation
Before you start
CAUTION
Many new and factory radios require a reset code when
disconnected from battery power. This is an anti-theft
feature. Before unplugging power, you must determine if
your radio/source unit requires a reset code. Check the
operation manual for your vehicle or contact the dealer.
1
2
3
5
7
6
8
11
12
4
POWER
REM turn on (Remote wire turn on)
when using High Level Input
- DC turn on
- Signal Sense turn on
Auto-Sense
Technical Guide
Turn on Mode
9
Model Fuse Size Cable Size
4ga
FA2-400.4
FA2-900.5
FA2-1000.1
FA2-1500.1
FA2-2000.1
Using spade terminals,connect
the speaker cables to the speaker
output connectors. Follow the
diagram below that best ts your
speaker conguration.
Speaker
Connections
Stereo
Monoblock single woofer multiple woofersMonoblock
Bridged
10
CH1 CH2
SPE AK ER SPE AK ER
REM
ON
DC
ON
SIGNAL
ON
MODE
NOTE - If the RCA’s are plugged into the amplier and the TURN ON MODE is in the
DC ON position, the amplier will NOT turn on. Please re-read QR document above or
hire a professional installer.
Setup Common System Setup
Quick Start
Installation Guide
2CH-Input CH1/CH2
Output CH1/CH2/CH3/CH4 (FA2-400.4)
Output CH1/CH2/CH3/CH4/CH5 (FA2-900.5)
4CH-Input CH1/CH2/CH3/CH4
Output CH1/CH2/CH3/CH4 (FA2-400.4)
Output CH1/CH2/CH3/CH4/CH5 (FA2-900.5)
5CH-Input CH1/CH2/CH3/CH4/CH5
Output CH1/CH2/CH3/CH4/CH5 (FA2-900.5)
The Crossover Mode switch sets the type
of crossover that will be active. 4 channel
models will have two switches, one for each
set of channels.
The HPF(high pass lter) control will limit the
output below the selected frequency. This
is typically used to protect midrange and hi
frequency speakers from damage and to
allow a smooth transition from a subwoofer.
The LPF(low pass lter) control
will limit output above the selected
frequency. This is used to allow
a smooth transition to the higher
frequency speakers.
1. If possible, with the source unit off, conrm that the primary volume control is
turned down (counter clockwise).
2. Turn on the source unit (CD, or MP3 player). Re-conrm that the volume is
turned down. Make sure the source unit controls; balance, fader, bass and
treble are all set to center or “0” adjustment. Make sure that the green LED on
the end of the amplier is illuminated.
3. Play a clean musical selection of which you are very familiar. CD is preferred.
Do not use radio signals for level setting. Hit play and start turning the volume
of the source unit up.
4. Stop increasing the source unit volume when you reach 3/4 (about 75%) or until
you hear speakers begin to slightly start producing distortion.
5. Increase the amplier level (clockwise) until distortion is heard, then back
the level down (counter clockwise) until the distortion is eliminated. Small
adjustments may need to be made to balance the levels of multiple ampliers.
The Bass Boost control will increase the
power output at 45Hz for more pronounced
bass. Exercise caution when using this
control. Increase the level in small amounts
until distortion is noticed, then back off a little.
Some models include a bass
remote. Avoid adjusting the bass
remote while operating vehicle.
Input Mode
Crossover
Mode
High pass
Adjustment
Low pass
Adjustment
Bass Boost
Remote Level
Control
4ch - Full Range
4ch - Mixed Mono
Mono
5ch
A
B
C
D
E
F
This is a critical step to insure your amplier
is properly adjusted to match the signal
output level of your source unit.
THIS IS NOT A VOLUME CONTROL!
Level Setting
G
WARRANTY
Maxxsonics, LLC. warrants this product, to the original consumer purchaser, to be free from
defects in material and workmanship for a period of one (1) year from the date of purchase.
Maxxsonics, LLC. will, at it’s discretion, repair or replace defective products during the warranty
period. Components that prove to be defective in materials and workmanship under proper
installation and use must be returned to the original authorized Maxxsonics, LLC. retailer from
where it was purchased. A photocopy of the original receipt must accompany the product being
returned. The costs associated with removal, re-installation and freight are not the responsibility of
Maxxsonics, LLC. This warranty is limited to defective parts and specically excludes any incidental
or consequential damages connected therewith. To view the full warranty, please visit the website.
The information contained within this document is intended to offer some basic guidelines
for a few of the most common installations. More complex audio systems should be
installed by a competent professional. Additional installation information available at
www.maxxsonics.com
MB Quart products are designed and engineered in the USA by
www.maxxsonics.com
Congratulations on your choice of a MB Quart amplier.
This “Quick Start Installation” guide is meant to help you
“hook up” and play music. For more detailed information,
on system setting, speaker and subwoofer conguration
and full specications by model visit the website,
https://mbquart.com/product-manuals/
MBQ FA2 QSG 01 - rev1
FA2-400.4
FA2-900.5
FA2-1000.1
FA2-1500.1
FA2-2000.1
5CH2CH 4CH
INPUT MODE
2CH 4CH
INPUT MODE
FULLHPF LPF
X-OVER
HPF
40Hz 400Hz
SUBSONIC
10Hz 40Hz
LPF
40Hz 400Hz
BASS BOOST
0dB +12dB
LEVEL
12v 0.2v

Tuotetiedot

Merkki: MB Quart
Kategoria: Vastaanotin
Malli: FA2-400.4

Tarvitsetko apua?

Jos tarvitset apua merkille MB Quart FA2-400.4 esitä kysymys alla ja muut käyttäjät vastaavat sinulle


Vastaanotin MB Quart Käyttöohjeet

MB Quart

MB Quart FA2-2000.1 Käyttöohje

29 Maaliskuuta 2025
MB Quart

MB Quart FA2-1500.1 Käyttöohje

29 Maaliskuuta 2025
MB Quart

MB Quart FA2-1000.1 Käyttöohje

29 Maaliskuuta 2025
MB Quart

MB Quart FA2-400.4 Käyttöohje

29 Maaliskuuta 2025
MB Quart

MB Quart FA2-900.5 Käyttöohje

29 Maaliskuuta 2025
MB Quart

MB Quart GMR1.5 Käyttöohje

16 Lokakuuta 2024

Vastaanotin Käyttöohjeet

Viimeisimmät Vastaanotin Käyttöohjeet

QSC

QSC SPA-Qf 60x2 Käyttöohje

1 Huhtikuuta 2025
Streacom

Streacom TL1 Käyttöohje

30 Maaliskuuta 2025
Graupner

Graupner GR-8 Käyttöohje

30 Maaliskuuta 2025
Pro-Ject

Pro-Ject Stereo Box DS Käyttöohje

29 Maaliskuuta 2025
Futaba

Futaba R7108SB Käyttöohje

28 Maaliskuuta 2025
Bresser

Bresser T-16 Käyttöohje

27 Maaliskuuta 2025
ETON

ETON MA 1 Käyttöohje

19 Maaliskuuta 2025
Elipson

Elipson P1 Käyttöohje

14 Maaliskuuta 2025
Elipson

Elipson Stream S300 Xi Käyttöohje

14 Maaliskuuta 2025
Elipson

Elipson WIIM Mini Käyttöohje

14 Maaliskuuta 2025